Johnson Controls Tyco PowerSeries Pro HS2TCHPRO User manual

HS2TCHPRO/HS2TCHPROBLK
Installation Instructions
Warning: Please refer to the System Installation Manual for information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer. These instructions shall be used in con-
junction with the system Installation Manual of the Control Panel with which this equipment is intended to be used.
29010964R001

Contents
Safety Instructions 4
Installation Instructions 5
Specifications 5
Unpacking 5
Mounting 6
Wiring 7
Basic Setup 8
Setting the Keypad Language 8
Enrolling the Keypad 8
Keypad Display Symbols 9
Proximity (Prox) Tags Support 9
Assign Proximity Tags 9
Delete Proximity Tags 9
Function Key Assignment 9
Available Function Key Options 10
Programming Labels 10
Optional Settings 11
Enable/Disable Fire, Medical, Panic Buttons 11
Extra Power Option 11
Change the Background Image 11
Dark Text Enable/Disable 11
Performing a firmware upgrade 11
Keypad Programming 11
[000] Keypad Partition Assignment 12
[011] Keypad Input/Output Programming 12
[012] Local PGM Output Pulse Activation Time 12
[021] First Keypad Options 12
[022] Second Keypad Options 12
[023] Third Keypad Options 13
[030] Download LCD Messages 13
[031] Download LCD Message Duration 13
[041] Indoor Temperature Zone Assignment 13
[042] Outdoor Temperature Zone Assignment 13
[101] - [348] Door Chime for Zones 1 - 248 13
Valid Entries 13
[991] Reset Keypad Programming to Factory Defaults 14
- 2 -

- 3 -
Approvals 14
FCC Compliance Statement 14
Industry Canada Compliance Statement 14
Simplified Declaration of Conformity 14
EN50131-1 Grade 3/Class II 14
Limited Warranty 15
SOFTWARE PRODUCT LICENSE 16

Safety Instructions
Read the safety information before you install the equipment.
Important: This equipment must be installed by a skilled person only. A skilled person is an installer with appropriate
technical training. The installer must be aware of potential hazards during installation and measures available to min-
imize risks to the installer and other people.
lBefore you install this equipment, disconnect all power sources (for example mains, battery, and telephone
line) connected to the alarm panel.
lInstall the equipment indoors in a non-hazardous environment where the following conditions are met:
lPollution degree - Maximum 2
lOver voltages - Category II
lInternal wiring must be routed to prevent strain on wire and terminal connections, loose terminal connections,
and damage to conductor insulation.
lInstruct the user that there are no user serviceable parts in this equipment. All equipment must be serviced
by a skilled person.
- 4 -

Installation Instructions
- 5 -
Installation Instructions
The HS2TCHPRO/HS2TCHPROBLK keypad can be used on security systems with up to 248 zones. These keypads are
compatible with the PowerSeries Pro panel models HS3128, HS3032, HS3248.
Specifications
lTemperature range: UL/ULC: 0°C to +49°C (32°F to 120°F); EN: -10°C to +55°C (14°F to 131°F)
lWeight: 405 g
lHumidity (MAX): 93% R.H. non-condensing
lPlastic enclosure protection degree: IP30, IK04 (touchscreen excluded)
lVoltage rating: 11.3 VDC to 12.5 VDC nominal
lCorbus low voltage: 9 VDC
lConnects to control panel via 4-wire Corbus
lCorbus distance: 101 m (332 ft. max.). Corbus distance in Extra Power mode: 54 m (177 ft)
lUp to 32 keypads per system
lHS2TCHPRO/HS2TCHPROBLK current draw (at 12 VDC): 100 mA standby (screen off); 160 mA activated or alarm
(Regular. power mode); 230 mA activated or alarm (Extra Power mode).
Note: This does not include 50 mA (max) using PGM output.
lWall mount tamper
lFour programmable function keys
lReady (Green LED), Armed (Red LED), Trouble (Yellow LED), AC (Green LED), HOME (White LED)
lKeypad size: 191 mm x 126 mm x 20.35 mm
lDisplay area size: 155 mm x 86 mm
lSD card slot: holds any standard Secure Digital (SD) card* (32 mm x 24 mm x 2.1 mm). *If necessary, the SD card
can be formatted to file system FAT16 or 32 using a PC. The maximum size SD card supported is 32 GB.
lWiring: standard four-wire connection
lView angle: horizontal viewing angle: 70° left, 70° right
lVertical view angle: 70° top, 50° bottom
lBrightness: 280 cd/m2
Note: On the HS3248 panel, the maximum number of partitions is 32 and the maximum number of keypads is 32.
For more information on the system configurations, refer to the Reference Manual.
Unpacking
The keypad package includes the following parts:
lOne keypad
lFive mounting screws and five anchors for wall-mounting
lOne tamper switch (required for UL commercial burglary listed installations)
lInstallation instructions and User manual

Mounting
Mount the keypad near designated points of entry and exit. Once a dry and secure location is selected, do the fol-
lowing:
1. If there is an SD card in the keypad, remove the SD card before opening the touchscreen. See Figure 1.
Warning: Do not disassemble the touchscreen without removing the SD card first.
2. Remove screw at the bottom of the keypad.
3. Insert screwdriver into slots and pry up to remove.
Figure 1 - Removing the Backplate
4. Secure keypad backplate to the wall using mounting holes, see Figure 2. Use all 4 screws provided unless mount-
ing on a single gang box. Use the plastic anchors if the unit is to be mounted on drywall. If using the keypad
tamper, secure the tamper plate to the wall with a screw.
- 6 -

Wiring
- 7 -
Figure 2 - Mounting the Backplate
Callout Description
1 Mounting holes
2 Wiring slot
3 Hole for tamper screw
Note: For ULC fire installations, the keypad must be mounted on top of an electrical box and used with conduit.
5. Run wire through wiring slot. Connect Corbus wiring to the keypad. See the Wiring section.
6. Place keypad into backplate, ensuring that the wire is pushed back into the wall as much as possible. Route the
wire inside the keypad ensuring high components are avoided. Snap the front assembly closed, ensuring it fits
flush with the backplate.
If any tension is found between the front keypad assembly and wiring, open the keypad, re-route the wire and close
again. Repeat these steps until the keypad is closed properly.
Wiring
1. Before wiring the unit, ensure that all power (AC transformer, telecommunications network, and battery) is dis-
connected from the control panel.
2. Connect the four corbus wires from the control panel (green, yellow, black and red) to the keypad terminals.
3. If the P/Z terminal is programmed as an input, a device such as a door contact may be connected to the keypad.
This eliminates the need to run wires back to the control panel for the device. To connect the zone, run one wire
from the device to the ‘P/Z’ terminal and the other wire from the device to the B (black) terminal. For powered
devices, run the red wire to the R (positive) terminal and the black wire to the B (negative) terminal.

4. If the ‘P/Z’ terminal is programmed as an output, a small relay (such as DSC model RM-1 or RM-2), buzzer or other
DC operated device may be connected between the positive supply voltage and the ‘P/Z’ terminal (max.load is
50mA).
Note: P/Z terminal is not to be used for fire applications but can be used for low risk ULC commercial burglary
applications.
Figure 3 - Wiring
HS2TCHPRO/
HS2TCHPROBLK
RED R
BLK B
YEL Y
GRN G
To zone or P/Z
PGM output
____
____
____
____
____
Basic Setup
This section describes how to configure the keypad, including enrollment, proximity tag setup, function key assign-
ment and label programming.
Setting the Keypad Language
Enter [000][000] then the two-digit language number.
Languages
01 = English (default) 08 = Czech 15 = Greek
02 - Spanish 09 = Finnish 16 = Turkish
03 - Portuguese 10 = German 18 = Croatian
04 - French 11 = Swedish 19 = Hungarian
05 = Italian 12 = Norwegian 20 = Romanian
06 = Dutch 13 - Danish 21 = Russian
07 = Polish 14 = Hebrew
Enrolling the Keypad
Keypads can be enrolled automatically or manually. In either case, the serial number of the device is used as an iden-
tifier.
Note: If no keypad is enrolled on the system, the touchscreen displays the following message when powered up:
Press the Enroll button. Once the touchscreen is enrolled, use it to enroll other keypads and modules. The following
enrollment methods are available:
[902][000] Auto Enroll
- 8 -

Basic Setup
- 9 -
When this mode is selected, the total number of keypads currently enrolled is displayed.
1. Enter [902][000] to begin auto-enrollment of new keypads. Keypads are assigned to the next available slot.
[902][001] Manual Enroll
1. Enter [902][001] or use the [<][>] keys and press [*].
2. When prompted, enter the serial number of the keypad found on the back of the keypad.
3. Once enrolled, the keypad model, serial number and slot assignment are displayed. The slot assignment can be
changed using the [<][>] keys.
4. To cancel the enrollment of a module, press [#].
[902][101] Unenroll Keypads
1. Enter [902][101] or use the [<][>] keys and press [*].
2. Use the [<][>] keys to scroll to the specific keypad to delete.
3. Press [*] to select the keypad and, when prompted, press [*] again to delete it.
Keypad Display Symbols
Ready Light (green) – If the Ready light is on, the system is ready for arming.
Armed Light (red) – If the Armed light is on, the system has been armed successfully.
System Trouble – Indicates that a system trouble has been detected.
AC – Indicates that AC is present at the main panel.
Proximity (Prox) Tags Support
A Prox tag can be used in place of an access code to perform functions on the system. Present the tag to the tag
reader .
Assign Proximity Tags
Using the keypad:
1. Press [*][5] Master/Supervisor Code].
2. Enter a 2-digit user code.
3. Press 2.
4. Pass the enrolled tag near the tag reader.
Delete Proximity Tags
To delete a proximity tag:
1. Select Options, Access Codes [enter Master code].
2. Select a user to delete.
3. Select Prox Tag Prog then delete.
Function Key Assignment
The HS2TCHPRO/HS2TCHPROBLK has 7 buttons on the Home screen, four of them programmable by the installer.
Function key 2 must always be set to "Away Armed."

To program function keys 1,3,4,5:
1. On the keypad, press [*][8][Installer Code].
2. Enter [861]-[892] to program keypads 1-32 respectively.
3. Enter [001-[005] for function keys 1-5 or use the [<][>] keys and press [*].
4. Enter a 2-digit number to assign a function key operation - [00]-[68].
See Available Function Key Options below.
5. Repeat from step 3 until function keys 1, 3, 4, 5 are programmed.
Function Key Function Option
1 Stay Arm 03
2 Away Arm (Do not change) 04
3 Alarm Memory 40
4 Trouble Display 39
5 User Functions 35
To program function key 6:
1. Press Options, Installer Menu [Installer Code], Keypad Programming then Home Functions.
2. The default for the function key 6 Home Page display is Keypad Mode. To display the Photo button on the
Home page, press Photos.
Available Function Key Options
The following table describes the available function key options:
[00] Null [02] Instant Stay Arm [03] Stay Arm
[04] Away Arm [05] No-entry Arm [06] Chime ON/OFF
[07] System Test [09] Night Arm [12] Global Stay Arm
[13] Global Away Arm [14] Global Disarming [16] Quick Exit
[17] Arm Interior [21] Command Output 1 [22] Command Output 2
[23] Command Output 3 [24] Command Output 4 [29] Bypass Group Recall
[31] Local PGM Activate [32] Bypass Mode [33] Bypass Recall
[34] User Programming [35] User Functions [37] Time/ Date Program
[39] Trouble Display [40] Alarm Memory [61] - [92] Partition Select 1 - 32
Programming Labels
1. From the HS2TCHPRO/HS2TCHPROBLK keypad, press Options, press Installer Menu [Installer Code], then press
Label Programming.
2. From the Label screen, select the item you want to label (e.g., zones, partitions, etc.).
- 10 -

Optional Settings
- 11 -
3. Enter the label name for the selected item.
4. Press Save when complete.
Optional Settings
The following settings are available through the Options menu.
Enable/Disable Fire, Medical, Panic Buttons
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.
2. Enable/disable the desired Fire, Medical and Panic buttons.
Extra Power Option
The Extra Power option will increase the brightness of the display. To enable the option:
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.
2. Enable or disable the extra power option.
Note: Enabling the Extra Power option will put the keypad into a higher current mode and the keypad will draw 300
mA. In Extra Power mode, reduce the maximum wire length from 101 m (332 ft.) to 54 m (177 ft.)
Change the Background Image
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Background Image.
2. Select an image to use from the SD card.
3. To exit, press the Back or the Home button.
Dark Text Enable/Disable
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.
2. Select the desired text color by enabling or disabling Dark Text. (This will make the text white).
Note: This feature affects only the text on the Classic (square) button home page.
Performing a firmware upgrade
Note: Use downloading software (DLS) to upgrade the keypad's main ST software.
1. Insert an SDcard in the HS2TCHPRO/HS2TCHPROBLK with the new firmware.
2. Press Options, Installer Menu [Installer Code], Keypad Programming, then Firmware Upgrade.
3. Select OK to perform a firmware upgrade.
Keypad Programming
To enter keypad programming:
1. Press Options then Keypad Mode. The virtual keypad is displayed.
2. Press [*][8][Installer Code].
3. Enter one of the following keypad programming sections:
l[860] Keypad Slot Number. This section is for display only.
l[861]-[892] to program keypads 1-32 respectively.
Once a keypad is selected, the following programming options are available:

[000] Keypad Partition Assignment
Valid entries are 00-32. |___|___|
[011] Keypad Input/Output Programming
Zone or PGM Number Default 000 |___|___|___|
[012] Local PGM Output Pulse Activation Time
|___|___| Minutes (00-99) |___|___| Seconds (00-99)
[021] First Keypad Options
Default Value Option ON Off
OFF |__| 1 Fire Key Enabled Fire Key Disabled
OFF |__| 2 Medical Key Enabled Medical Key Disabled
OFF |__| 3 Panic Key Enabled Panic Key Disabled
ON |__| 4 Display Access Code When Programming Display Xs When Programming Access Codes
Note: For EN50131-1/EN50131-3 compliant systems, section [021], options 1 and 2 must be off..
[022] Second Keypad Options
Default Value Option ON Off
ON |__| 1 Local Clock Display ON Local Clock Display OFF
OFF |__| 2 Local Clock Displays 24-hr Clock Displays AM/PM
ON |__| 3 Auto Alarm Mem Scroll ON Auto Alarm Mem Scroll OFF
ON |__| 4 For Future Use For Future Use
OFF |__| 5 Power LED Enabled Power LED Disabled
ON |__| 6 Power LED - AC Present ON Power LED - AC Present OFF
ON |__| 7 Alarms Displayed While Armed Alarms Not Displayed While Armed
OFF |__| 8 Auto-Scroll Open Zones ON Auto-Scroll Open Zones OFF
- 12 -

Keypad Programming
- 13 -
Note: For UL/ULC installations, bit 5 (PowerLED) and bit 6 (Power LED Indicates AC Present) shall be ON.
[023] Third Keypad Options
Default Value Option ON Off
OFF |__| 1 Armed LED Power Save Armed LED Off in Sleep Mode
ON |__| 2 Keypad Status Shows Stay Arm Keypad Status Shows Stay/Away Arm
OFF |__| 3 5th Terminal Keypad PGM Output 5th Terminal is Keypad Zone Input
ON |__| 4 Prox tag will arm/disarm Prox tag does not arm/disarm
OFF |__| 7 Local Display of Temperature No Local Display of Temperature
OFF |__| 8 Low Temperature Warning Enabled Low Temperature Warning Disabled
[030] Download LCD Messages
|___|___|___|___|___|___|___|___|___|___|___|___|___| ___|
|___|___|___|___|___|___|___|___|___|___|___|___|___| ___|
[031] Download LCD Message Duration
Default: 000 |___|___|___|
(Valid entries are 000-255, 000=Unlimited Msg Display) This number represents the number of times the down-
loaded message must be cleared before it is permanently removed. This message can be cleared by pressing any
key.
[041] Indoor Temperature Zone Assignment
Default: 000 |___|___|___| (Valid entries are 000-248)
[042] Outdoor Temperature Zone Assignment
Default: 000 |___|___|___| (Valid entries are 000-248)
[101] - [348] Door Chime for Zones 1 - 248
The keypad can be programmed to make up to four different chime sounds for individual zones (e.g., for Zone 1,
enter section [101], for Zone 2 enter section [102]).
Default: 01 |___|___|
Valid Entries
01 6 Beeps
02 Bing-Bing tone
03 Ding-Dong tone

04 Alarm tone (4 second duration)
[991] Reset Keypad Programming to Factory Defaults
1. Press [*][8][Installer Code].
2. Enter [991].
3. Use the [<][>] keys to scroll to the applicable keypad.
4. Press [*] to select the keypad.
5. Re-enter [Installer Code].
6. Press [*] to reset the selected keypad to factory defaults.
Approvals
FCC Compliance Statement
Caution: Changes or modifications not expressly approved by DSC could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accord-
ance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type
tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of
Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any res-
idential installation. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to television or radio reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or more of the following meas-
ures:
lRe-orient the receiving antenna
lRelocate the alarm control with respect to the receiver
lMove the alarm control away from the receiver
lConnect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional sug-
gestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radi-
o/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington,
D.C. 20402, Stock # 004-000-00345-4.
Industry Canada Compliance Statement
CAN ICES-3(b)/NMB-3(b)
Simplified Declaration of Conformity
Hereby, Tyco Safety Products Canada Ltd. delares that the radio equipment type in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
HS2TCHPRO(BLK): http://dsc.com/1903007
EN50131-1 Grade 3/Class II
The Model HS2TCHPRO/HS2TCHPROBLK Keypad has been certified by Telefication according to EN50131-1:2006 +
A1:2009 + A2:2017, EN50131-3:2009 for Grade 3, Class II.
- 14 -

Limited Warranty
- 15 -
Note: For EN50131 compliant installations the following functions (initiated from the keypad emergency buttons)
have to be disabled:
lFire Alarm function
lAuxiliary (Medical) Alarm function
lPanic Alarm function
Limited Warranty
Digital Security Controls (DSC) warrants that for a period of 12 months from the date of purchase, the product shall
be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such war-
ranty, DSC shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair
depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or
handling, or damage due to causes beyond the control of Digital Security Controls such as lightning, excessive
voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the
equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all
other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security
Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to
act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning
this product. In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages,
loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase,
installation or operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system be completely tested on a regular basis.
However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is pos-
sible for this product to fail to perform as expected. Important Information: Changes/modifications not expressly
approved by DSC could void the user’s authority to operate this equipment.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copy-
righted and is purchased under the following license terms:
This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who
acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products
Canada Ltd. (“DSC”), the manufacturer of the integrated security systems and the developer of the software and any
related products or components (“HARDWARE”) which You acquired.
If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE,
and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The
SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials, and “online”
or electronic documentation.
Any software provided along with the Software Product that is associated with a separate end-user license agree-
ment is licensed to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the Software Product, You agree uncon-
ditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous
arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the Software
Product to You, and You have no right to use it.

SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intel-
lectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE - This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE
PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used
concurrently on or from different computers, including a workstation, terminal or other digital electronic device
(“Device”). In other words, if You have several workstations, You will have to acquire a license for each workstation
where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per
license installed at any given time. You may use the back-up copy solely for archival purposes. Except as expressly
provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed mater-
ials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer,
decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly per-
mitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Soft-
ware, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or
labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and
conditions of this EULA.
(b) Separation of Components - The Software Product is licensed as a single product. Its component parts may not
be separated for use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If you acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT
is licensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be
used with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or
post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent
sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (includ-
ing all component parts, the media and printed materials, any upgrades and this EULA), and provided the recipient
agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior
versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the
terms and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its
component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of
DSC or its suppliers.
- 16 -

Limited Warranty
- 17 -
3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited
to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed mater-
ials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed
materials accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which
may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may
be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights
to use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any coun-
try, person, or entity subject to Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding
arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The
place of arbitration shall be Toronto, Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT
THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED
OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the
operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-
DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE
IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER
ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY
PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF
ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON
THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER
PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT
ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY,
BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE,
BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT,
COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME,
PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.

WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite fre-
quent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this
SOFTWARE PRODUCT to fail to perform as expected.
Operating Instructions shall be made available to the user.
The trademarks, logos, and service marks displayed on this document are registered in the United States [or other
countries]. Any misuse of the trademarks is strictly prohibited and Tyco International Ltd. will aggressively enforce its
intellectual property rights to the fullest extent of the law, including pursuit of criminal prosecution wherever neces-
sary. All trademarks not owned by Tyco International Ltd. are the property of their respective owners, and are used
with permission or allowed under applicable laws. Product offerings and specifications are subject to change without
notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; con-
tact your sales representative.
This product contains open source components QT Version 4.7.3 and Linux Kernel License: Version 2.6. Both of these
components are protected by copyright and have terms and conditions associated with their use. The open source
software code and associated components used in this product are downloadable from the DSC website. Please visit
http://www.dsc.com/open-source-documentation for detailed information.
© 2020 Johnson Controls. All rights reserved. JOHNSON CONTROLS, TYCO and DSC are trademarks of Johnson Con-
trols. • www.dsc.com •
Tech Support: 1-800-387-3630 (Canada, US), 905-760-3000
- 18 -