Johnson Controls IQ Panel User manual

We hope you enjoy your new IQ Panel security and smart home platform. It will serve as the
“brain” of your home for many years to come. With it you can control your lights, locks,
thermostat, security and much more.
You won’t need a manual to operate your IQ Panel, but you can use this guide to learn more
about the features of this amazing new device. We hope it will add to your home’s decor and
make your home smarter and more energy efficient!
SECURITY&
SMARTHOME
Document: IQP23-8–18
Revised on: 09/29/2020
Software Version: 2.5.3
IQ PANEL USER GUIDE

GETTING STARTED
Start by connecting your power. (Note: If your panel has been professionally installed, skip this page
Plug in the power connector
Route the wire behind the
retainer clip
Insert the wire into the
strain-relief
Now put on your cover and attach the table stand.
Place the top of the cover onto
the panel’s back plate
Push the cover down until it
snaps in place
Insert the table stand into the
mounting holes and push
upward until it snaps into place
Plug in your panel, power it on
Plug in the power supply
provided with your panel
Push and hold the standby
button on the side of the panel
for 3 seconds
Once the panel powers up, the
home screen will appear.

USING YOUR SYSTEM: BASICS
Swipe down to
access settings
Touch an icon to
view its contents
Swipe left/right
to change pages
Swipe a page away
when you are done
Navigation
Move from page to page
and access information on
each page using finger
touches, swipes, and
scrolling.
Scroll up/down to reveal
additional content on a page
Dismiss
To dismiss a pop up when
you are done, swipe left or
right to dismiss.

USING YOUR SYSTEM: MESSAGE CENTER
Contact
Easy access to your provider’s contact information, including phone
number, email, and website.
Video Tutorials
Watch videos to help you understand your system and service better.
To watch a video, touch a thumbnail. Video will begin playing
automatically.
Video controls appear on screen, To exit, touch the “back” button.
Alerts/Alarms
Alerts and alarms from your system like low battery alerts, alarms, and
power failures.
To dismiss, touch the circle to the left of the message and touch “OK” to
remove it from your message center.
You can also remove all messages at once by touching “Acknowledge All”
11/11/20
Message Center
Access your message center by touching the icon in the upper right corner. Once its open you’ll
see three sections: Contact, Video Tutorials, Alerts/Alarms, and Messages.
(Note: This icon may appear different than shown, depending on your provider’s settings)
Messages
Messages from your provider will also appear here.
To dismiss, touch the circle to the left of the message and touch “OK” to
remove it from your message center.
You can also remove all messages at once by touching “Acknowledge All”

USING YOUR SYSTEM: EMERGENCY PANIC
Emergency Panic
If you have a police, fire, or medical emergency and your system is not armed or a sensor has not been triggered, you
can send a manual emergency panic by touching the icon in the bottom right corner and selecting the type of
emergency you are experiencing. (Note: based on your location, not all options may appear or be available to you.)
Two-Way Voice
If your provider offers Two-Way Voice
service you’ll be able to speak to the
monitoring agent from the speakers and
microphone built right into your panel.
There’s a
stranger in my
backyard!
To send a police or emergency panic
without sounding the siren, using the
“Silent Alarm” at the bottom of the screen
Alarm Types
Canceling an Emergency Panic
To cancel an emergency panic, touch the
“cancel” button and enter a valid user code.
X
Cancel
Police: When touched it triggers the “Police”
siren pattern and sends a police emergency
signal to your provider’s monitoring station.
Fire: When touched it triggers the “Fire” siren
pattern and sends a fire emergency signal to
your provider’s monitoring station.
Emergency: When touched it triggers the
“Emergency” siren pattern and sends an
emergency signal to your provider’s
monitoring station.

Sensor status:
USING YOUR SYSTEM: ARMING
Arming Options
Quickly choose from “stay” or “away”
Touch to access
arming options
Sensor List
Open or active sensors
appear in a scrollable list
on the right. Touch the
icons in the upper right
corner to switch your
view to either “Active”
or “All” sensors.
?
Open
Closed
Active
Idle
Unreachable
Tampered
Synchronizing
See add’l options by touching
the “>>” icon on the right
Additional Arming Options
Select these options before choosing your arming type
Arming Stay
Arms doors and windows only
Arming Away
Arms doors, windows and motions
Additional Options
View additional arming options by touching the “>>”
icon on the right side.
Bypass
Touch the circle next to a sensor to bypass it during
the arming sequence
Exit Sounds
The panel beeps as the timer counts down. Silence
these beeps before you choose the arming type.
Entry Delay
The panel will give you time to disarm once a “delay
door” has been opened. Turn this off with a touch.

USING YOUR SYSTEM: DISARMING
Touch to disarm
panel manually
Disarming your System
When your system is armed, there are multiple ways to disarm:
Disarming Manually
To manually disarm your panel, touch the icon in the center of the
screen. You will be prompted to enter a valid code. Failure to
enter a valid code with the time required will trigger the alarm.
When someone manually disarms the panel the built in
camera will take a photo and save it on the camera page
along with the date, time, and name of the user.
Disarming Remotely
To remotely disarm your panel, login to your mobile app and touch
the “disarm” icon.
Disarming Automatically
You can connect your smartphone using Bluetooth and it will
automatically disarm your IQ Panel from an “Armed Away” state when it
comes within range. To connect a phone, follow the steps shown.
*You can connect up to five (5) smartphones for
touchless disarming. You may need to enable this
setting in your Bluetooth settings.
Bluetooth
Touchless
Disarming
Step 1:
Swipe down to
access settings
tray
Step 2:
Touch “SETTINGS”
Step 4:
Enter your code
Step 5:
Touch “BLUETOOTH DEVICES”
Step 3:
Touch “ADVANCED SETTINGS”
Pair
Step 7:
Touch “ADD DEVICE” The panel
will begin searching for new
devices in range (It may take up
to 60 seconds)
Step 9:
Touch “Pair”
Step 10:
When the messages appear on your
phone and IQ Panel, ensure the numbers
match and touch “Pair” on each.
Bluetooth Pairing Request
“IQ-Panel” would like to pair
with your phone. Confirm that
the code “12345” is shown on
the “IQ-Panel”.
Cancel
Pair
BLUETOOTH PAIRING REQUEST
CANCEL
PAIR
Device: My Phone
Pairing Code: 12345
Step 6:
Put your Bluetooth device in “pairing”
mode.
Step 8:
Select your device from the list
Download the
Alarm.com app
in the App store
or Google Play
Note: Remote disarming has not been evaluated by UL/cUL

ALARM EVENTS
Alarms
If the alarm is triggered the IQ Panel will sound
the siren and display a red alarm screen.
Police
When the system is armed and the
alarm is tripped or you touch the
“Police” emergency button the alarm
sounds with the “Intrusion” siren and
then activates the Two-Way Voice
microphone and speaker, if available.
Fire
When a Smoke or Carbon Monoxide
detector is triggered or someone
taps the “Fire” panic on the IQ Panel
the alarm sounds with the “Fire”
siren and then activates the Two-
Way Voice microphone and speaker,
if available.
Emergency
When you press an IQ Pendant or
trigger an emergency signal from the
IQ Panel, the alarm sounds with the
“Emergency” siren and then activates
the Two-Way Voice microphone and
speaker.
Speakers are located on each side of the panel
Microphones are located on the bottom of the panel
Two Way Voice
The built in microphones on the bottom of the
panel and the Two-Way Voice speaker on the
side of the panel activate after a connection to
the monitoring station has been made.
If your provider offers monitoring service, the
panel will automatically contact your monitoring
center using the dual path LTE and Wi-Fi
connection.
To disarm, touch the screen and enter your
passcode.
Preventing false alarms:
False alarms are a terrible waste of your public service
resources, and can erode your relationship with local
authorities. In some areas, authorities even charge a fee for
false dispatches.
Here’s some tips for avoiding false alarms:
-Use your system regularly, be comfortable with its operation.
-Make sure everyone who has access to your home has a valid
access code and is familiar with how to use the system.
-Ensure the doors you use the most are set up with delays to
give you enough time to disarm the system when you open a
door.
-Test your system regularly
-Develop a routine.
-Use alternative methods for arming and disarming (mobile
app, bluetooth disarming, etc.)
False Alarms
In the event of a false alarm, press disarm and
enter your user code. If your system is
monitored, be ready to provide your verbal
password to your security provider’s monitoring
agent if they contact you. If you are NOT able
to provide the correct verbal passcode, the
authorities may be contacted.

USING YOUR SYSTEM: CAMERA
Camera Page
Your IQ Panel’s built in camera captures photos in a variety of situations:
Disarm Photos
When the panel is disarmed manually, the built in camera takes a
photograph and saves it in the “ARM/DISARM” section. These
photos are accompanied by the username of the individual who’s
code was used, the date, and the time.
Settings Photos
When someone attempts to access your panel settings with an
invalid code, the built in camera takes a photograph and saves it
in the “SETTINGS” section. These photos are accompanied by
the date and time.
Alarm Photos
When the alarm is triggered, the built in camera takes a
photograph and saves it in the “ALARMS” section.
1- View Photo
Touch a photo thumbnail on the right
to view it on the left.
2- Full Screen
Touch the photo on the left to view it
full screen. Touch it again to return
to the camera page.
Note: While viewing photos full
screen you can swipe left/right to
view additional photos
Alarm.com/Login
Get your username
and password from
your provider
Photos to your Phone
Click the “Image
Sensor” tab
Click “Rules &
Alerts”
Click “Capture Alarm And
Disarm Images” to customize
Note: For supplementary use only, not part of the Fire and Security system
Alarm Videos
When the alarm is triggered, the built in camera will record up to a
4 minute video clip. This video is stored locally on the panel only.
1
2
3
3- Saving Photos to a Micro SD Card
When a Micro SD card is inserted in the panel, a SD card icon
will appear. Tab that icon to see options that will allow you to
save your photos and videos to the SD card. You can select
individual photos and videos or choose to “Save All”. Once
you have selected your photos, select “Copy to SdCard”.

USING YOUR SYSTEM: SETTINGS
Settings Tray
Access common settings by swiping down
from the top of the screen.
Security Status
See your panel’s
security status in the
upper right. Touch it
to go directly to the
security page
Battery & Radios
Touch an icon to get
more information
-Battery level
-Wi-Fi connection
-Bluetooth status
-LTE connection
Volume
Slide left/right to adjust
the panel voice
Brightness
Slide left/right to
adjust the screen
brightness
Settings
Touch to access the
full settings page.
From there you can
also access
“Advanced
Settings” (which will
require a passcode)
Messages & Alerts
Touch to access the message
center including your
provider’s contact information,
video tutorials, and system
messages
Photo Frame
Touch to access the
photo frame where you
can customize the
panel’s screensaver
Clean Screen
Disables the screen for 30 seconds
to allow you to clean it without
accidentally touching anything.
(Touch the “standby” button on the
side of the panel to cancel)
Language
Touch to change
panel language
Close Tray
Swipe up to
close the tray
Settings Page
From here you can adjust individual sound
settings, change your weather temperature
from Fahrenheit to Celsius, see the status of
your security and smart home devices, and
more.
Advanced Settings
Only the Master code can access this area.
From here you can manage users, run system
tests, reboot your system, connect Bluetooth
and Wi-Fi and more.
HOW TO ACCESS:
SOUND
DISPLAY
SD CARD
WEATHER
TEMPERATURE
STATUS
Z-WAVE DEVICES
STATUS
OTHER Z-WAVE
DEVICES
AUTOMATION
ADVANCED
SETTINGS
ACTIVITY MONITOR

USING YOUR SYSTEM: ADVANCED SETTINGS
Advanced Settings: Can only be accessed using the Master code.
About
View important information
about your system such as:
current software version,
IMEI, hardware version, etc.
This is a great place to look
if troubleshooting an issue
with Tech Support.
System Tests
Perform various system test
to ensure your system is
working properly. This is
another great place to go if
troubleshooting an unknown
issue with the system.
Edit Sensor
Don’t like the names of your
sensors? Easily customize
your sensor names from
here. You can also adjust
the chime type and turn
Voice Prompts on and off
from here.
Panel Reboot
Use this option if needing
to restart your panel. If
you’re experiencing
problems with your
system, try performing a
panel reboot. Often times,
a system restart can help a
system run more smoothly.
Power Down
Use this option if needing
to shut the system down
for any reason. Shutting
the system down any
other way can cause
potential issues.
Bluetooth Devices
Easily turn on the bluetooth
radio from here. This allows
you to use the touch-less
disarming feature. You can
add, delete and edit your
devices from here.
Wi-Fi
Connect the system to an
internet connection to ensure
the panel has a second path of
communication. This will help
speed up the communication
time to the central station and
greatly improve speed when
controlling home automation.
Sound
From the sound menu,
you can adjust the
volumes to your panel
voices, beeps and
chimes, and video
tutorials. You can also
edit sensor chimes, Z-
Wave device prompts,
Trouble Beeps and
touch sounds.
Important Note
If for some reason you are unable to access the settings
screen and need to reboot the system, you can do a hard
reboot by holding the power button on the side for 30
seconds. This should only be done if absolutely necessary.
!
For additional help and questions
on Advanced Settings, please
reach out to your security dealer.
IQ Remote Devices
From here, you can test
Remote Wi-Fi signal
strength and rediscover
Remotes that have lost
connection.
Access Point Settings
Enable and disable access
point for use with Wi-Fi
devices. Check with your
dealer before enabling or
disabling or you could cause
devices to loose connection.
User Management
Program up to 242
individual user codes for
each person that needs
access to the system.
Assign a name to each
code so that you know
who disarmed the system.
Master Settings
Choose your first and
second preferred languages
to be toggled from the
settings tray (see previous
page) and require dealer or
installer permission to
access panel settings

SETTINGS: PHOTO FRAME
Photo Frame
When your panel is not in use, it turns into a
customizable photo frame.
Touch “ADD”
Delete
Touch a photo to select it. Touch
“Delete” to delete it from your panel
Add Photos
To add your own photos:
1
3
4
Touch each photo you wish to use or
choose “Select All”
3
4
Save your Photos onto a Micro SD card in
a folder called “Photos”
2
Insert your SD card into the slot on the
side of the panel
4
5
5
Choose either “Add” or “Replace”
Add: Does not delete the photos already on
the panel, only adds the photos you
selected
Replace: Deletes the photos already on
the panel and replaces them with the
new photos you selected
6
Wait at least 60 seconds after the photos
have copied to remove the SD Card
Settings
Inside settings you can choose whether you
want photos or a weather clock, if you want
the panel to turn itself off automatically in
the evenings, and more.

SETTINGS: ADDING A USER
Name
User Code
Confirm User Code
Type
Expiration Date
Add User
Enter Name
Please enter User Code
Please confirm User Code
User
Unlimited
Step 1:
Swipe down to access
settings tray
Step 2:
Touch “SETTINGS”
Step 4:
Enter your code*
Step 3:
Touch “ADVANCED
SETTINGS”
Step 5:
Touch “User Management”
Add User
Step 6:
Touch “Add User”
How to Add a New User
User Types
You can add up to 242 users to your
system, each with a custom name and
access level you allow.
Master: Access panel functions, camera,
and system settings.
User: Access panel functions, camera, but
NOT system settings.
Guest: Used to give arm and disarm
access to those users who will use the
panel on a temporary basis
Expiration Date: Choose a specific date
that will disable a user code
automatically.
Notifications
By creating individual users, you can set up custom text
notifications when they access or use your system,
keeping you connected no matter where you are.
Add User Screen
Once on the “Add User” screen you can create a custom
name and user code and indicate whether you want this
person to be a Master, User, or Guest.
*Default master code is 1234. For security purposes this code should be
changed once the system has been installed in your home

SETTINGS: TESTING YOUR SYSTEM
Testing Regularly
You should test your system regularly to ensure it is operating at peak efficiency. The IQ Panel has a
number of tests built in that are easy to perform:
Step 1:
Swipe down to access
settings tray
Step 2:
Touch “SETTINGS”
Step 4:
Enter your master code*
Step 3:
Touch “ADVANCED
SETTINGS”
Step 5:
Touch “System Tests”
How to Access System Tests
Wi-Fi Test
Run this test every 30 days or if the IQ
Panel’s Wi-Fi connection seems to be failing.
Encounter a Problem?
If you encounter a problem with
your system, contact your provider
right away.
Touch “Message Center” in the
upper right corner of your
panel to get your provider’s
contact information
Sensor Test
Run this test every 30 days. As you start
the test, open and close your doors,
windows, and move in front of your motion
sensors to ensure they work as expected.
Cellular/LTE Test
Run this test if your panel seems to have
lost its ability to send and receive signals.
Image Sensor Config
Run this test if your image sensors stop
working
Z-Wave Test
A series of Z-Wave tests to optimize your
smart home network. “Reconfigure
network” is your most useful test, repairing
your network for you.
Dual Path Test
Run this test if your panel seems to have
lost its ability to send and receive signals.
Panel Glass Break Test
Use this to test your panel’s microphone
Panel Test
Use this every 30 days to test a variety of
panel functions
*Default master code is 1234. For security purposes this code should be
changed once the system has been installed in your home
1

USING YOUR SYSTEM: LIGHTS
Light Control
You can add up to 80 Z-Wave lights, lamp modules, or lightbulbs to your IQ Panel. This will allow you to
control your lights locally on the panel and also from your mobile app. Once your first light is added to
your system, the lights page will appear. Simply swipe over to access it.
ON
Touch turn on all
selected lights
OFF
Touch turn off all
selected lights
GET STATUS
Touch to check the
status of all selected
lights
Select
Touch the circle next
to a light to select it
Energy
Touch the energy icon to see how much energy
the outlet is currently using
Dimmer
Touch the slider
from left to right
to adjust the
brightness of a
single dimmer
ON/OFF
Touch a bulb or
outlet icon to
turn it on or off
LIGHT ON
LIGHT OFF
SMART SOCKET ON
SMART SOCKET OFF
Mobile Access
You can also control your lights from your mobile
app.

USING YOUR SYSTEM: LOCKS
Lock Control
You can add up to 6 Z-Wave locks to your IQ Panel. This will allow you to control your locks locally on
the panel and also from your mobile app. Once your first lock is added to your system, the lock page
will appear. Simply swipe over to access it. If you have more than one lock swipe up and down to
access each one.
UNLOCK ALL
Touch to unlock all
your locks at once
LOCK ALL
Touch to lock all
your locks at once
Get Status
Touch the refresh
icon to check the
lock’s current status
ON/OFF
Touch the key
icon to unlock
or lock it
Change Locks
If you have
more than
one lock,
swipe up and
down to
access each
one.
UNLOCKED
Mobile Access
You can also control
your locks from your
mobile app.
LOCKED

USING YOUR SYSTEM: THERMOSTAT
Mode
Touch to change this
thermostat from heat to cool
(or off) or use “automatic”
which switches from heat to
cool as needed to maintain
your target temperature.
Current Temp
Displays the
current
temperature in
your home
Fan
Touch to
change to “On”
or “Automatic”
Up/Down
Touch the
arrows to
adjust the
target
temperature
Switch
If you have
more than
one
thermostat,
swipe up and
down to
access each
Mobile Access
You can also control your
thermostat from your mobile
Thermostat Control
You can add up to 6 thermostats to your IQ Panel. This allows you to control the temperature in your
home locally on the panel and also from your mobile app. Once your first thermostat is added to your
system, the thermostat page will appear. Simply swipe over to access it. If you have more than one
thermostat swipe up and down to access each one.
Battery level
Displays how
much battery is
left in your
thermostat

USING YOUR SYSTEM: GARAGE DOOR
Garage Control
You can add up to 10 Z-Wave overhead garage door controllers to your IQ Panel. This allows you to
control the door from your panel and also from your mobile app. Once your first garage opener is added
to your system, the garage page will appear. Simply swipe over to access it. If you have more than one
overhead garage door swipe up and down to access each one.
GARAGE CLOSED
GARAGE OPEN
Open/Close
Touch the icon
to open or
close the
garage door
Switch
If you have
more than
one garage
door, swipe
up and down
to access
each one.
Open
Touch the icon to
open the garage
door (not available
when the garage
door is already
closed)
Close
Touch the icon
to close the
garage door (not
available when
the garage door
is already
closed)
OPEN ALL
CLOSE ALL

USING YOUR SYSTEM: LIVE VIEW
Live View
Easily view the live video feed from your Alarm.com video cameras on the 7” panel screen. This page
will appear automatically if cameras are added to the account and the authorization has been given on
the Alarm.com customer website. Supports live view of up to 40 cameras. Supported models: ADC-
V521IR, ADC-V522IR, ADC-V622, ADC-V722W, ADC-VC725, ADC-VC726, ADC-VC825 & ADC-VC826.
Camera
View
A thumbnail of
the camera will
be displayed for
the highlighted
camera. Click
the play button
to view full
screen.
Cameras List
All supported
cameras that are on
the account and
have been
authorized will
show here. Click
the camera you
would like to view.
Exit
Click on the
red X icon to
exit full screen
mode.
Camera View
Full screen mode
can be activated
by clicking on the
play button for
each individual
camera.
Important Note
Cameras will only
push to your panel if
you have authorized
them to do so from
your Alarm.com
customer website.
This can be found
under Video Settings.

USING YOUR SYSTEM: LIVE VIEW WITH AUDIO
Live View with Audio
Listen in and speak to any room in the house using the Qolsys Live View with Audio feature. This can be
done from your mobile app or right from the 7” touch screen. If your camera supports two-way audio,
the talk button will automatically appear on the live view page.
Talk
Press and hold while
talking to to use the
two-way audio feature
built into your camera.
Listen
Press to turn
on audio.
End
Press this
button to exit.
Hold To
Talk
Press and hold
to talk.
LIVE VIEW
~ with Audio ~
ON PANEL