Johnson Controls Bentel Security tyco ABSOLUTA Plus User guide

ABSOLUTA Plus 4.00
Expandable Hybrid Control Panel
Installer Manual
Default Installer PIN: (A)0104 (00104 for Grade 3 Control Panels)
EN 50131 Grade 2 and Grade 3*

Always use the most recently BOSS console software to program the ABSOLUTA Plus control panel.
The programming of an ABSOLUTA control panel cannot be imported to an ABSOLUTA Plus control panel; therefore, if
you replace an ABSOLUTA motherboard with an ABSOLUTA Plus motherboard, you must re-set ALL control panel
options.
Installation of the system must be carried out strictly in accordance with the instructions described in this manual, and in
compliance with the local laws and bylaws in force.
The GSM,ABS-GSM and IP, ABS-IP modules must be installed by Service Persons only (service person is defined as a
person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be
exposed in performing a task and of measures to minimize the risks to that person or other persons).
The GSM,ABS-GSM and IP, ABS-IP modules must be installed and used within an environment that provides the pollution
degree max 2, over voltages category II, in non-hazardous, indoor locations only.
All instructions specified within this manual must be observed.
The ABSOLUTA Plus control panels have been designed and manufactured to the highest standards of quality and
performance.
The ABSOLUTA Plus control panels have no user-changeable components, therefore, they should be serviced by authorized
personnel only.
BENTEL SECURITY does not assume responsibility for damage arising from improper application or use.
The manufacturer recommends that the installed system should be completely tested at least once a month.
Hereby, BENTEL SECURITY, declares that ABSOLUTA Plus control panels comply with the essential requirements and
other relevant provisions of Directive:
2014/35/EU The Low Voltage Directive
2014/30/EU The Electromagnetic Compatibility Directive
MAINTENANCE
Please verify the correct operation of security system at least once a month.
Periodically, perform the steps below.
— Remove dust accumulation on the panel container, with a damp cloth without use any type of solvent.
— Check the status of the connections and wires.
— Check inside the panel there are no foreign bodies.
— For other security-system devices, such as smoke detectors, infrared and microwave detectors, and inertial detectors, refer
to the instructions for maintenance and testing.
RECYCLING INFORMATION
BENTEL SECURITY recommends that customers dispose of their used equipments (panels, detectors, sirens, and other
devices) in an environmentally sound manner. Potential methods include reuse of parts or whole products and recycling of
products, components, and/or materials.
For specific information see: http://www.bentelsecurity.com/index.php?o=environmental
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) DIRECTIVE
In the European Union, this label indicates that this product should NOT be disposed of with household waste. It should
be deposited at an appropriate facility to enable recovery and recycling.
For specific information see: http://www.bentelsecurity.com/index.php?o=environmental
BENTEL SECURITY S.r.l. reserves the right to change the technical specifications of this product without prior notice.
*) See Table 2 on page 7.

TABLE OF CONTENTS
INTRODUCTION 5
About the Control Panel 5
Features 6
Common Features for all versions 6
ABSOLUTA Plus 18 features 7
ABSOLUTA Plus 48 features 7
ABSOLUTA Plus 128 features 7
Control Panel versions 8
Grade 3 Control Panels 8
The boxes 8
The Main Boards 9
The Power Supplies 9
The Accessories 9
Plug-In Modules 9
Compatible items 9
Access Levels for panel management 11
Technical Specifications 12
IDENTIFICATION OF PARTS 15
MOUNTING THE COMPONENTS 19
Mounting the Metal Box 19
Mounting the Plastic Box 20
Installing the GSM Module 22
Installing the IP Module 23
INSTALLING 25
Mounting the Control Panel 25
Mounting the BPI Peripherals 25
Terminals 25
Wiring 27
Connecting BPI Bus Devices 27
BPI bus Wiring Limitations 28
Connecting Detectors 28
Connecting Motion Detectors 29
Connection of Grade 3 detectors 30
Connecting Roller-Blind and Vibration Detectors 31
Connecting Fire Detectors 31
Connecting Alarm Signalling Devices 32
Supervised Output 33
Connecting Tamper Terminals 33
Connecting the Telephone Line 34
Connecting the AS100 Audio Station 35
Connecting the transceiver 35
Power Supply 36
Power connection 36
Power disconnection 37
Wizard setup 37
Thermal Probe 39
Hardware Default 40

PROGRAMMING FROM THE PC 41
Options with requirements 41
Minimum system requirements 41
Configuration 42
Keypads 42
Expander In 43
Expander Out 43
Key Readers 43
Power station 44
Wireless Module 45
General 45
Wireless Detectors 46
Wireless Sirens 46
Wireless Repeaters 47
Zones 48
Partitions 53
Phonebook 55
Audio Session 55
Priority 56
Outputs 56
Voice Messages 58
System Options 59
General 59
Time 62
Received Call 63
Phone Options 63
Advanced Call Options 65
EN50131/EN50136 65
Installer 66
Events and Actions 67
OUTPUTS ACTIVATION 67
VOCAL ACTIONS/AS100 - CALLS 67
SMS 68
CENTRAL STATION ACTIONS 69
Event Description 70
Remote Command Events 70
Caller ID over GSM events 71
Default settings 71
Smart Actions 79
Smart SMS 79
Emails 82
APP Notification 82
Partitions 82
Emails 83
Addresses 83
Partitions 83
Users: Codes and Options 83
Users: Keys 85
Users: Keyfobs 86
Arming Schedule 87
Time Table 87
Partitions Event Editor 88
Perpetual Calendar 88
Timers 88
Time Table 88
Timer Event Editor 88
Perpetual Calendar 88
GSM 89
Pay As You Go 89
App/BOSS Cellular Communication 89
Cellular 90
Disabling event transmission to the receivers 91
IP 92
SMS Messages 94
Downloading/Uploading 95
Connecting the Control Panel to the PC 95
How Downloading/Uploading the Options 97
KEYPAD OPERATIONS 99
Using the keypad 99
Access to the operations 100
Quit from the Operations 102
1.1) Zone Test 103
1.2) Output Test 104
1.3) Changing the PIN 104
1.4) Firmware and Keypad Language Upgrade by
an USB key 105
1.6) Modify the Keypad language 106
1.7) Enabling Level 4 access 107
1.8) Clear Faults and Tampers 107
1.9) Option Programming by Keypad 108
Zones 108
Partition 108
User PINs 109
Keys 109
WLS Keys 109
System 109
Key Reader 109
Keypad 109
2.1) Voice Message Recording 110
2.2) BPI Device enrolling 110
2.3) Wireless Device enrolling 111
2.4) Key enrolling 112
2.5) Message Download/Upload via USB Key 113
2.6) Option Download/Upload via USB Key 114
2.7) Factory Default 115
2.8) Telephone Communicator 115
2.9) Key Disabling/Enabling 116
3.1) View Logger 116
3.2) View the Firmware Version 117
3.3) View Zone Status and Zone Bypassing 117
3.4) View GSM Module Status 118
3.5) View IP Module Status 119
APPENDIX 121
Quick guide for the LCD keypad menu 121
Wired zone automapping 121
Wireless device mapping 121
Reporting Formats 122
Contact ID 122
SIA 122
Options EN50131/EN50136 125
Connection via IP 126
Local IP connection (LAN) 126
Remote IP Connection (Internet) 126
Wireless device options 128

INTRODUCTION
About the Control Panel
The full-featured ABSOLUTA Plus security systems have
been especially designed to satisfy all security needs,
from residential to advanced industrial applications.
The objective of the ABSOLUTA Plus is to make
end-user operation simple and help the Installer im-
prove efficiency. This is achieved by simpler software
and firmware, and remote programming and diagnostic
facilities.
This system provides impressive application flexibility
and many interesting features such as monitoring facili-
ties and telephone access.
The ABSOLUTA Plus range of panels includes three
main models based on a common platform.
ABSOLUTA Plus 18 Expandable control panel up to
18 hardwired zones (wired plus wireless). This control
panel is suitable for basic applications in the residential
and small commercial sectors.
ABSOLUTA Plus 48 Expandable control panel up to
48 hardwired zones (wired plus wireless). This control
panel is suitable for middle to high level applications in
the residential sector and to the middle level installa-
tions in the commercial and enterprise sector.
ABSOLUTA Plus 128 Expandable control panel up to
128 zones (wired plus wireless). This control panel is
suitable for high level applications in the residential sec-
tor and to the middle to high level installation in the com-
mercial and enterprise sector.
Partitions ABSOLUTA Plus manages independent
partitions — all with stay and away control. Each Parti-
tion (group of zones) can be programmed with its own
Entry/Exit and Auto-Arm/Disarm Times, etc., and can
be controlled by digital Keys/Cards, Codes and/or Input
zones.
Events and Actions ABSOLUTA Plus manages
about 2000 events. The factory default settings have
been purpose programmed to require few or no
changes for standard applications. However, the pro-
gramming flexibility of the Events and Actions (Output,
Digital communicator and Voice Dialler Actions) will al-
low you to fully customize the system.
Communications The Communicator manages 32
telephone numbers for vocal communications and SMS
messages (through the optional GSM Module, the
ABS-GSM) and digital communications to Central Sta-
tions. Each Communicator number can have its own
Account Code and Reporting format (usually assigned
by the Central station).
3In order to comply with EN50131 Grade 3 stan-
dards, it is essential to use the ABS-IP IP module
for the notification of alarms: the built-in PSTN
communicator and GSM/GPRS ABS-GSM Module
can be used simultaneously.
Remote Service The Remote Service makes it possi-
ble to carry out actions on the Control Panel at a dis-
tance, without physically operating the components:
basically programming (downloading/uploading op-
tions) and diagnosing Control Panel status.
The Remote Service can be implemented via Internet
using the optional GMS module, ABS-GSM, and/or the
optional IP module, ABS-IP.
Voice Messages The ABSOLUTA Plus manages 206
recordable Voice Messages for the Voice Dialler, and
voice driven menu facilities.
Voice communications to and from the Control Panel al-
low operations such as: Listen-in, 2 Way Audio, Input
status enquiry (with Voice answer); Remote control of
appliances (Turn ON/OFF); Arm/Disarm Partitions;
Alarm Reset and Inhibit Calls.
Access to all the “over-the-phone” features requires a
Telephone Access Code which can be disabled
immediately after use.
Scheduler The Scheduler can be setup to Arm/Disarm
Partitions automatically (on a daily or weekly basis),
and to control 16 daily timer events.
Wireless Devices The ABSOLUTA Plus control
panel supports up to 128 BW wireless devices and up to
16 BW keyfobs, by using the BW-PGH transceiver (op-
tional).
Programming This Control Panel can be programmed
from the Keypad, or via the BOSS Software Application
and a computer. The Software Application (runs under
Windows) provides real-time supervisory facilities (via
connection to a RS232 or USB Interface, or
Teleservice), and will allow you to make the fullest use
of all the system features.
ABSOLUTA Plus INTRODUCTION 5

Features
nCommon Features for all versions
Zones/outputs dynamic allocation Each zone and
each output can be programmed as “Not used”. This
will allow the installer to have the maximum number of
zones even if an expander is not fully used. The panel
will build a correspondence between the number of a
zone and its physical location.
E.g. the zone nr. 7 can be located on expander nr. 1,
terminal T1, and the zone nr. 8 can be located on ex-
pander nr. 2, terminal T4.
On board Inputs
r4 zones.
r4 Programmable Terminals (Zones/Outputs).
rZones supervision (NC / NO / EOL / DEOL).
rFully-programmable input-zones.
r1 supervised (10 Kohm EOL) 24h Tamper Zone.
On board outputs
r1 Programmable Alarm Output 2 A relay (Bell output).
r2 Programmable Open-Collector Outputs (100 mA
each).
r4 Programmable Terminals (Zones/100 mA Outputs).
rFully Programmable Output options (polarity, Tim-
ing, Events, Timers).
rSupervised Bell circuit.
Peripherals ABSOLUTA M-Touch, ABSOLUTA
T-Line, LCD PREMIUM and CLASSIKA keypads, Ex-
pander M-IN/OUT module, PROXY2 and ECLIPSE2
Key readers, BXM12 Power supply stations.
+When using the M-Touch keypad with control pan-
els based on the ABS-128 motherboard, do not
use more than 104 zones. The M-Touch keypad
may give unreliable indications for the zones be-
yond the 104 recommended.
Wireless
r1 transceiver at 868 MHz.
Interfaces
rBPI Plus bus (+12 V only).
rBus for BW-PGH transceiver.
rPC-Link interface.
rUSB OnTheGo Device/Host.
Options AS100 2-way audio station for remote listen-
ing (speaker and microphone).
Communications
rIntegrated PSTN interface.
rPhone Line monitoring.
rDouble Call.
rLine-sharing Management.
rUp to 32 telephone numbers for Voice/SMS Dialler
and Central Station.
rSupports CONTACT ID and SIA Reporting Formats.
rProgrammable Test Call.
rRemote servicing.
rPeriodic Transmission Test.
rIntegrated Voice Calls.
rUp to 206 voice messages, total time 20.7 minutes.
rVoice Guide by Telephone, with Remote DTMF de-
vice management.
rDown-loadable Pre-Recorded Voice messages.
Features ABS-18 ABS-48 ABS-128
Zones on Board (Min/Max) 4/8
Outputs on Board: Relay 1
Outputs on Board: Open Collector (Min/Max) 2/6
Max number of Zones (Wired plus Wireless) 18 48 128
Max number of Wireless Sirens (1) 16 16 16
Max number of Repeaters 888
Max number of Outputs 16 20 50
Max Number of Input Expanders 32 32 32
Max Number of Output Expanders 16 16 16
Max Number of Keypads 8816
Max Number of User PINs 31 63 127
Installer PINs 1
Level 4 PINs 1
Max Number of Key Readers 16 32 32
Max Number of Keys 64 128 250
Max Number of Keyfobs 16 16 32
Max Number of Power Supply Stations 444
Max Number of Transceivers 1
Max Number of Audio Stations 1
GSM Module 1
IP Module 1
Partitions 8816
Max Number of Events in Logger 2,000
Timers 16
Voice Messages 1 x 12 seconds + 205 x 6 seconds
Telephone Numbers 32
Table 1 Characteristics of the various types of Control Panel: 1) Each wireless siren can take up to four logic outputs,
one output for each siren sound, so the maximum number of sirens is limited by the maximum number of outputs.

Management
r127+1 Programmable Codes (from 4 to 6 digits).
rSupports a total of 250 SAT Keys and/or Proxy-Cards.
rProgrammable Automatic Arming/Disarming features.
rPartition Bypass for Patrol purposes with automatic
or manual re-arming.
r5 Partitions Arming Mode:
– Away arming;
– A, B, C, D modes (each mode can be programmed
for any action on partitions).
(Only A and B modes are available for key-readers)
rProgramming from a LCD or Touchscreen keypad.
rLocal programming from a PC via RS232/USB.
rLocal/remote downloading/programming.
rAccepts commands from touch-tone phones (Arm,
Disarm, Turn ON/OFF Outputs, Partition and Zone
status check).
rRemote Talk/Listen-in (requires optional AS100
2-way audio station).
rRemote Telephone Access via DIALLER or
ANSWER.
r2000 event memory with date and time details.
rPriority management of events (processing and re-
porting): 1) Alarm/Hold-up, 2) Tamper, 3) Trouble
and Bypass.
r3 function keys for immediate Alarm calls from Keypad.
GSM/GPRS Only with the optional ABS-GSM Module.
rQuad Band
rSupport for the GSM/GPRS channel
rMain or backup dialler
rTransmission of voice messages by GSM
rTransmission of Contact ID and SIA by GSM
rTransmission of events in Contact ID and SIA format
via GPRS to Sur-Gard SYSTEM II/III receivers
rReporting of events by SMS
rLibrary of 250 SMS messages: 1 heading message,
8 status messages, and 241 personal messages
r32 events controlled by SMS
r32 events controlled by caller ID (at no cost)
rChecks the control panel’s status by SMS
rArm/Disarm Partitions via SMS (ONLY Grade 2 Con-
trol Panels)
rChecks the credit left on the prepaid SIM card
rTeleservice by Internet (GPRS)
IP Only with optional ABS-IP module.
rEthernet interface
rTransmission of Contact ID and SIA events to IP re-
ceivers using FIBRO Protocol to Sur-Gard SYSTEM
I,II and III IP receivers
rProgramming and monitoring of the ABSOLUTA
Plus control panel on the LAN using BOSS
rProgramming and monitoring of the ABSOLUTA
Plus control panel via the internet, using BOSS
rManagement of the ABSOLUTA Plus control panel
via the internet, using the ABSOLUTA app
rEvent notification via e-mail and on the ABSOLUTA
app (push notifications)
rInterface for ABSOLUTA Plus integration with
third-party software
Power supply Deep discharge battery protection.
Housing
rmetal box for 17 Ah battery, with BAW35T12,
BAW50T12 or BAW75T12 power supply and 2
M-IN/OUT
rplastic box for 7 Ah battery, with BAQ15T12,
BAW35T12 or BAW50T12 power supply and 1
M-IN/OUT
nABSOLUTA Plus 18 features
rUp to 8 Keypads
rUp to 16 Key Readers
rUp to 32 Input Expanders (on the M-IN/OUT modules,
and PREMIUM and ABSOLUTA T-Line Keypads)
rUp to 16 Output Expanders (on the M-IN/OUT modules)
rUp to 18 fully-programmable wired zones
rUp to 16 Outputs
rUp to 18 wireless zones (with external receiver)
rUp to 18 total zones (wired + wireless)
rUp to 8 independent Partitions
nABSOLUTA Plus 48 features
rUp to 8 Keypads
rUp to 32 Key Readers
rUp to 32 Input Expanders (on the M-IN/OUT modules,
and PREMIUM and ABSOLUTA T-Line Keypads)
rUp to 16 Output Expanders (on the M-IN/OUT modules)
rUp to 48 fully-programmable wired zones (with exter-
nal Input Expanders)
rUp to 20 Outputs (with external Output Expanders)
rUp to 48 wireless zones (with external receiver)
rUp to 48 total zones (wired + wireless)
rUp to 8 independent Partitions
nABSOLUTA Plus 128 features
rUp to 16 Keypads
rUp to 32 Key Readers
rUp to 32 Input Expanders (on the M-IN/OUT modules,
and PREMIUM and ABSOLUTA T-Line Keypads)
rUp to 16 Output Expanders (on the M-IN/OUT modules)
rUp to 128 fully-programmable wired zones (with ex-
ternal Input Expanders)
rUp to 50 Outputs (with external Output Expanders)
rUp to 4 power Supply Stations
rUp to 128 wireless zones (with external receiver)
rUp to 128 total zones (wired + wireless)
rUp 16 independent Partitions
ABSOLUTA Plus INTRODUCTION 7
Versions Main
Boards Boxes Power Supplies
ABS18P15*ABS-18
ABS-P
BAQ15T12
ABS18P35*BAW35T12
ABS48P35*ABS-48 BAW35T12
ABS48P50*BAW50T12
ABS128P50*ABS-128 BAW50T12
ABS18M35 ABS-18
ABS-M
BAW35T12
ABS48M35*
ABS-48
BAW35T12
ABS48M50*BAW50T12
ABS48M75*BAW75T12
ABS128M50*
ABS-128
BAW50T12
ABS128M75*BAW75T12
ABS128M75-G3** BAW75T12
Table 2 *) Grade 2 control panels
**) Grade 3 control panels

Control Panel versions
You can create the Control Panels listed below, by assem-
bling the available components, as shown in the Table 2.
ABS18P15 Up to 8 Zone Control Panel, expandable
up to 18 zones, in Plastic Box with 1.5 A Power Supply.
ABS18P35 Up to 8 Zone Control Panel, expandable
up to 18 zones, in Plastic Box with 2.6 A Power Supply.
ABS48P35 Up to 8 Zone Control Panel, expandable
up to 48 zones, in Plastic Box with 2.6 A Power Supply.
ABS48P50 Up to 8 Zone Control Panel, expandable
up to 48 zones, in Plastic Box with 3.6 A Power Supply.
ABS128P50 Up to 8 Zone Control Panel, expandable
up to 128 zones, in Plastic Box with 3.6 A Power Supply.
ABS18M35 Up to 8 Zone Control Panel, expandable
up to 18 zones, in Metal Box with 2.6 A Power Supply.
ABS48M35 Up to 8 Zone Control Panel, expandable
up to 48 zones, in Metal Box with 2.6 A Power Supply.
ABS48M50 Up to 8 Zone Control Panel, expandable
up to 48 zones, in Metal Box with 3.6 A Power Supply.
ABS48M75 Up to 8 Zone Control Panel, expandable
up to 48 zones, in Metal Box with 5.4 A Power Supply.
ABS128M50 Up to 8 Zone Control Panel, expandable
up to 128 zones, in Metal Box with 3.6 A Power Supply.
ABS128M75 Up to 8 Zone Control Panel, expandable
up to 128 zones, in Metal Box with 5.4 A Power Supply.
nGrade 3 Control Panels
The Control Panels listed below are shipped partially
assembled and adopt some measures that make them
compliant with Grade 3 of the EN50131 standard.
3Since this manual is common to all Control Panel
versions, this note will be used to highlight the spe-
cific characteristics of Grade 3 Control Panels.
In addition, from time to time specific characteristics of
Grade 2 and Grade 3 Control Panels will be high-
lighted.
ABS128M75-G3 Up to 8 Zone Control Panel, expandable
up to 128 zones, in Metal Box with 5.4 A Power Supply.
The packaging of the ABS128M75-G3 control panel in-
cludes the following components:
Øthe backplate with tamper and wall-tamper switches
mounted
Øthe Cover
Øthe ABS-128 main board
Ø1 identification label of the type of Control Panel
Øthe BAW75T12 Switching Power Supply
ØFive 12 mm plastic supports for the Main board
ØEight 10 mm plastic supports for two input/output ex-
panders
ØOne 12 cm earth wire (Yellow-Green) with eyelet
Ø1 plastic wall-tamper bracket
ØTwo (1 x 3 mm) cogged metal washers
Ø1 self tapping screw 3 x 6 mm to secure the Earth
wire (Yellow-Green) with eyelet
ØOne (3 x 8 mm) screw to secure the power supply
Ø2 adapters for connecting the battery 17 Ah
ØOne 40 cm cable for connecting the battery
ØSeventeen 10 Kohm resistors (brown/black/or-
ange/gold), 16 for Single and Double Supervision of
the Zones and 1 for the Supervision of the Tamper Line
ØNine 2.2 Kohm resistors (red/red/red/ gold), 8 for triple
tupervision of the zone, 1 for supervision the +A output
ØEight 8.2 Kohm resistors (grey/red/red/gold) for triple
supervision of the zone
ØEight 22 Kohm resistors (red/red/orange/gold) for tri-
ple supervision of the zone
Ø1 Info sheet (Italian/English/French/Spanish/Portu-
guese/Dutch)
nThe boxes
The following Boxes are available for the ABSOLUTA
Plus control panels.
ABS-P Is a plastic box that supports the ABS-18,
ABS-48 and ABS-128 main boards, and the 1.5 A,2.6
and 3.6 A power supplies. In addition it can house a
backup battery up to 7Ahand an M-IN/OUT Input/Out-
put Expander Module. The Plastic Box package in-
cludes the following parts:
Øthe backplate with the tamper switch mounted
Øthe cover
ØOne 21 cm earth wire (Yellow-Green) without eyelet
Ø2 self tapping screws — 3.5 x 12 mm to secure the
cover
ØFive 3 x 8 mm Parker screws (2 to secure the main
board, 2 to secure the power supply and 1 to secure
the possible input/output expander
Ø2 “Premises protected” Labels (English and Italian)
ABS-M Is a metal box that supports the ABS-18,
ABS-48 and ABS-128 mother boards, and the 2.6 A,
3.6 A and 5.4 A power supplies. In addition it can house
a backup battery up to 17 Ah and up to two M-IN/OUT
Input/Output Expander Modules. The Metal Box pack-
age includes the following parts:
Øthe Backplate
Øthe Cover
ØFive 12 mm plastic supports for the Main board
ØEight 10 mm reverse locking supports for two In-
put/Output Expanders
ØOne 12 cm Earth wire (Yellow-Green) with eyelet
Ø1 plastic wall-tamper bracket
ØTwo (1 x 3 mm) cogged metal washers
ØTwo M4x8 mm metric screws to secure the Cover
ØOne 3 x 6 mm metric screw to secure the Earth wire
(Yellow-Green) with eyelet
ØTwo3x8metric screw to secure the power supply
Ø2 adapters for connecting the battery 17 Ah
Ø1 Tamper switch
8 Expandable Hybrid Control Panel

ØTwo 3 x 5.5 mm nuts for fixing the tamper switch in
place
Ø2 “Premises protected” Labels (English and Italian)
nThe Main Boards
The following Main Boards are available for the
ABSOLUTA Plus control panels.
ABS-18 Up to 8 zone main board, expandable up to 18
zones.
ABS-48 Up to 8 zone main board, expandable up to 48
zones.
ABS-128 Up to 8 zone main board, expandable up to
128 zones.
The Main Board package includes the following parts:
Øthe Main Board
Ø1 identification label of the type of Control Panel
ØOne 40 cm cable for connecting the battery
ØSeventeen 10 Kohm resistors (brown/black/or-
ange/gold), 16 for Single and Double Supervision of
the Zones and 1 for the Supervision of the Tamper
Line
ØOne 2.2 Kohm resistors (red/red/red/gold) for super-
vision of Output +A
Ø1 Info sheet (Italian/English/French/Spanish/Portu-
guese/Dutch)
nThe Power Supplies
The following Power Supplies (Type A - EN50131-6)
are available for the ABSOLUTA Plus control panels.
BAQ15T12 1.5 A @ 13.8 Vdc Switching Power Supply.
BAW35T12 2.6 A @ 13.8 Vdc Switching Power Supply.
BAW50T12 3.6 A @ 13.8 Vdc Switching Power Supply.
BAW75T12 5.4 A @ 13.8 Vdc Switching Power Supply.
+Read the Power Supply’s instructions for more in-
formation.
nThe Accessories
The following accessories are available to improve the
performances of the ABSOLUTA Plus control panels.
MAXIASNC Switch for open/removal detection.
KST Thermal Probe.
nPlug-In Modules
The following plug-in modules can be installed inside
the ABSOLUTA Plus box to expand the capability of the
control Panel.
M-IN/OUT Input/Output Expander.
ABS-GSM GSM Module.
ABS-IP IP Module.
Compatible items
Following a brief description of the items supported by
the ABSOLUTA Plus, shown on the Table 3: refer to the
items instructions for further information.
ABSOLUTA Plus INTRODUCTION 9
ABS-IP IP Module
ABS-VAP11G WiFi Bridge
ABS-GSM GSM Module
BGSM-100CA GSM Antenna for metal box (ABS-M)
ABS-AK GSM Antenna for plastic box (ABS-P)
ANT-EU External GSM Antenna
M-IN/OUT 6 Input/Output Expander
ABSOLUTA
M-Touch Touchscreen Keypad
ABSOLUTA
T-Black
LCD keypad with Input/Output
Expander and Proximity Reader
on-board, black
ABSOLUTA
T-White
LCD keypad with Input/Output
Expander and Proximity Reader
on-board, white
PREMIUM LCD
LCD Keypad with Input/Output
Expander and Proximity Reader on
board
CLASSIKA LCD LCD Keypad
ECL2-UKR
(ECLIPSE2)
Recessed Universal Reader
Module for Proximity Key
ECL2-C
(ECLIPSE2)
Cover for ECL2-UKR Universal
Reader Module
PROXI2 Indoor/Outdoor Proximity Reader
(IP34), for Proximity Key
SAT2 Proximity Key
PROXI-CARD Proximity Card
MINIPROXI Proximity Tag
PROXI-TAG/B Black Proximity Tag
PROXI-TAG/G Gray Proximity Tag
PROXI-TAG/W White Proximity Tag
AS100 Microphone + Loudspeaker
Station
BRM04/12 4-Relay module for open-collector
outputs
BXM12/30-B 3.6 A BPI Power Supply Station
BXM12/50-B 5.4 A BPI Power Supply Station
BW-PGH 868 MHz transceiver
BW-REP 868 MHz repeater
MAXIASNC Big NC Tamper Switch
KST Thermal Probe
USB5M 5 m USB Cable
BOSS Console Software
Table 3 Compatible items.

ABS-IP This is an IP module that allows you to con-
nect the ABSOLUTA Plus control panel to a LAN
through the Ethernet interface or via WiFi, using the
WiFi bridge ABS-VAP11G supplied on request. This
makes it possible to:
Øprogram, monitor and check the control panel via the
BOSS application installed on a PC connected to the
same LAN as the control panel itself;
Øprogram, monitor and check the control panel via the
BOSS application installed on a PC connected to the
control panel via the Internet;
Ømonitor the control panel using receivers Sur-Gard
SYSTEM I,II and III, via IP;
Øcheck the control panel and report events notification
on iPhone and Android smartphones via the
ABSOLUTA app (push notifications);
Øreport events via e-mail (push notifications).
ABS-GSM This is a GSM module that can be used by
the control panel as a backup dialler if the internal
PSTN dialler malfunctions or is tampered or can re-
place it completely in areas accessed by mobile phone
services where a PSTN line is not available.
In that sense, the GSM Module is completely transpar-
ent to the control panel for the following functions:
Øtransmission of voice messages over a GSM chan-
nel;
Øtransmission of events with Contact ID and SIA pro-
tocol over a GSM channel;
Ømanaging the control panel by telephone.
3In order to comply with EN50131 Grade 3 stan-
dards, it is essential to use the ABS-IP IP module
for the notification of alarms: the built-in PSTN
communicator and GSM/GPRS ABS-GSM Module
can be used simultaneously.
The GSM Module also allows you to:
Øsend SMS messages to a series of telephone num-
bers in order to report events (alarms, tampers, trou-
bles, etc.);
Øactivate/deactivate the actions of the control panel
(outputs, voice messages, etc.) by sending SMS
messages to the number of the GSM Module;
Øactivate actions just by recognizing the number that
is calling the GSM Module (at no cost);
Øcheck the control panel’s status by phone by sending
and receiving SMS messages;
ØArm/Disarm the Partitions via SMS (ONLY Grade 2
Control Panels);
Øperform Teleservice (remote management and pro-
gramming of the control panel) over the Internet on a
GPRS channel.
M-IN/OUT The M-IN/OUT is an Input/Output Expander
which allows the number of zones and outputs of the
Control Panel to be increased. It can be programmed to
function as: 6-zone Input Expander; Output Expander
with 6 Outputs; Input/Output Expander with 4 zones
and 2 Outputs; Input/Output Expander with 2 zones and
4 Outputs. In this manual the term Input Expander will
be used to refer to the M-IN/OUT programmed to func-
tion as an Input Expander or Input/Output Expander;
the term Output Expander will be used to refer to the
M-IN/OUT programmed to function as an Output
Expander or Input/Output Expander.
+An M-IN/OUT programmed as an Input/Output Ex-
pander contributes both to the number of Input Ex-
panders and to the number of Output Expanders
connected to the Control Panel.
eIn order to comply with EN50131-1 and EN50131-3
standards, the tamper and wall-tamper contacts of
the M-IN/OUT installed outside of the panel con-
tainer, must be enabled: the M-IN/OUT’s TAMP
DIS jumper must be removed.
Access Control Devices The ABSOLUTA Plus sup-
ports ECLIPSE2 and PROXI2 digital key readers, and
M-touch, T-Black, T-White, PREMIUM LCD and
CLASSIKA LCD keypads.
The operating principles of the ECLIPSE2 and PROXI2
readers are the same, except:
ØECLIPSE2 reader accepts the proximity keys, cards
and tags listed in Table 3 on page 9, and are for in-
door use (unless mounted inside weatherproof
boxes);
eThe ECLIPSE2 Key Reader is classified by the
EN50131-3 standard as Auxiliary Control Equip-
ment (ACE), Type A.
ØPROXI2 reader has weather strips, and can be in-
stalled indoors or outdoors (IP34 Protection Class)
and accepts the proximity keys, cards and tags listed
in Table 3 on page 9.
ECLIPSE2 and PROXI2 readers operate without con-
tacts, therefore, are highly resistant to oxidization and
wear.
eThe PROXI2 Proximity Reader is classified by the
EN50131-3 standard as Auxiliary Control Equip-
ment (ACE), Type A.
ØThe operating principles of the T-Black,T-White,
PREMIUM and CLASSIKA Keypads are the same,
with a large display (2 lines of 16 characters); only
the T-Black,T-White and PREMIUM Keypads have
on-board proximity reader.
eThe T-Black,T-White and PREMIUM LCD
keypads, and the CLASSIKA LCD and M-Touch
keypads, are classified by the EN50131-3 stan-
dard as Auxiliary Control Equipments (ACE), re-
spectively Type B and Type A.
ØThe M-Touch keypad has a large display allowing
the graphical display of information about the system
in colour. In addition, the display is touch sensitive so
interaction with this keypad is easy and intuitive.
BW-PGH transceiver The ABSOLUTA Plus control
panel supports BW wireless devices using the
BW-PGH transceiver.
10 Expandable Hybrid Control Panel

The BW-PGH transceiver supports wireless detectors,
wireless sirens, and keyfobs. The maximum number of
wireless devices supported depends on the
ABSOLUTA Plus control panel model, as indicated in
Table 1 on page 11.
For the complete and updated list of supported wireless
devices, see the Bentel Security website.
3In order to comply with EN50131 Grade 3 stan-
dards, Wireless Devices may NOT be used or, at
most, can be used in Grade 2 subsystems.
The ABSOLUTA Plus control panel can detect alarm,
tamper, low battery and lost wireless detectors.
When a wireless detector (assigned to a zone) detects
alarm conditions, the control panel will generate the re-
spective Alarm on zone event, and other events which
depend on the programmed type (refer to “Type” under
“Zones”).
When a wireless detector (assigned to a zone) detects
tamper conditions, the control panel will generate the
respective Tamper on zone event, and other events
which depend on the programmed type (refer to “Type”
under “Zones”).
When the battery of a wireless detector (assigned to a
zone) is low, the control panel will generate a Low bat-
tery on Wireless Detector event.
When a wireless detector fails to transmit a supervisory
signal within a certain time frame, the control panel will
generate a Lost of Wireless Detector event.
Some wireless devices can measure the temperature
and light intensity of the environment in which they are
installed. The control panel generates specific events
when the temperature and brightness thresholds are
exceeded; you can assign the desired actions to these
events. The LCD keypads show the average tempera-
ture measured by the devices.
Wireless sirens can emit different sounds to identify the
type of alarm (burglary, fire, gas, and flooding) or for
other applications.
The two-way keyfobs are able to show the status of the
security system.
Power station The power station has been especially
designed for Security system applications. The tamper
protected box (protected against opening and forced
removal) can house a backup battery for power supply
during black-out. The ABSOLUTA Plus control panel
supports BXM12/30-B 3.6 A power station and
BXM12/50-B 5.4 A power station.
BOSS The BOSS application (runs under Windows)
provides full Programming, Customer Database and
real-time Supervisory functions, and will allow you to
make the fullest use of all the system features.
Access Levels for panel management
Level 1 Access by any person: at this level you can ac-
tivate only the Super-keys (the keys 1, 2 and 3 pressed
for at least 3 seconds). Eg. 1: Emergency, 2: Fire,
3: Alarm.
Level 2 Access by the Master, Limited and Normal
user, after entering a PIN (see “Quick guide for the LCD
Keypad menu” in the “APPENDIX” section).
Level 3 Access by the Installer and Super User
(Grade 3 Control Panels ONLY), after entering a PIN
and having been enabled by a Master User (see
“KEYPAD OPERATIONS” section and “Quick guide for
the LCD Keypad menu” in the “APPENDIX” section).
Level 4 Access by the manufacturer’s qualified per-
sonnel, after entering a PIN and have been enabled by
the installer (see “KEYPAD OPERATIONS” section and
“Quick guide for the LCD Keypad menu” in the
“APPENDIX” section).
ABSOLUTA Plus INTRODUCTION 11

Technical Specifications
Table 4 on the following page shows the technical spec-
ifications of the ABSOLUTA Plus series.
The following table shows the current draw (I (mA) col-
umn) and size of the accessory components.
Components I
(mA)
Size
(WxHxD mm)
ABSOLUTA Plus Main
Board 200 175x99x17
ABS-GSM Module 250 99x65,5x12
ABS-IP Module 300 99x65,5x12
ABSOLUTA M-Touch keypad 300 195x127.9x20.3
ABSOLUTA T-Line Keypad
with proximity reader enabled
with proximity reader disabled
60
50
134x114x28,5
PREMIUM Keypadwith
proximity reader enabled
with proximity reader disabled
60
50
134x114x28.5
CLASSIKA Keypad 50 144.5x116x27.5
ECLIPSE2 Key Reader 30 —
PROXI2 Key Reader 30 78x108x22
M-IN/OUT Programmable
Input/Output Expander 20 108x101x34
BRM04/12 4 Relay Module 120
BXM12/30-B Power Station 10 240x348x97
BXM12/50-B Power Station 10 240x348x97
12 Expandable Hybrid Control Panel

ABSOLUTA Plus INTRODUCTION 13
Versions
ABS18P15 ABS18P35
ABS48P35
ABS48P50
ABS128P50
ABS18M35
ABS48M35
ABS48M50
ABS128M50
ABS48M75
ABS128M75
ABS128M75-G3
Voltage 230 V~
-15/+10%
50/60 Hz
110-230 V~-15/+10% 60-50 Hz
Max. Current Draw 0.42 A 0.75 A 1.1 A 0.75 A 1.1 A 1.7 A
Power Supply Battery-Charger
(Type A - EN50131-6)
13.8 V_
±2% 1.5 A
13.8 V_
±1% 2.6 A
13.8 V_
±1% 3.6 A
13.8 V_
±1% 2.6 A
13.8 V_±1%
3.6 A
13.8 V_±1%
5.4 A
Insulation Class I
Maximum ripple voltage on
the outputs 310 mV (2.25%)
Battery
(Brand and Type)
Lead Acid 12 V / 7 Ah
YUASA NP 7-12 FR or
similar Case Flame Class UL94-V2 or
higher
Lead Acid 12 V / 17 Ah
YUASA NP 17-12 FR or
similar Case Flame Class UL94-V2 or higher
Max. Current available for
peripherals and loads (Aux
Output)
380 mA
(7 Ah battery)
1200 mA*
(17 Ah battery)
Max. Battery Charge Current
(Battery capacity)
0.92 A
(7 Ah)
2.02 A
(7 Ah)
3.02 A
(7 Ah)
1.2 A
(17 Ah)
2.2 A
(17 Ah)
4.0 A
(17 Ah)
Maximum Battery Recharge
Time to 80% 24 h
Minimum Duration of
Alternative Power Supply 12 h
Low Battery Fault
Generated 11.4 V
Generation of Low Output
Voltage Fault, without
backup batteries
11.2 V
Overvoltage Protection N/A 16.7 V
Deep Discharge Protection 9.6 V
Digital Key Combinations 4,294,967,296
Alarm Transmission System
(ATS)
SP2 (with built-in PSTN communicator)
SP5 (with ABS-GSM or ABS-IP module)
DP1 (with integrated PSTN communicator and ABS-GSM or ABS-IP module)
DP4 (with ABS-GSM and ABS-IP modules)
Interface type between SPT
and AS** Proprietary
Alarm transmission operation
mode (acknowldgement) Pass-through
Delay for alarm messages
generation and
transmission
2s
Delay for fault detection and
visualization 2s
IP Protection Grade IP20
Security Grading 2(3forABS128M75-G3 control panel)
Environmental Class II
Operating Temperature -10 to +40 °C
Operating Humidity (not
condensed) 0 to 93% RH
Dimensions (WxHxD) 319x352x92 mm (without antenna) 310x403x103 mm (without antenna)
Weight 2.09 Kg (without battery) 4.89 Kg (without battery)
Complies with EN60950-1; EN50130-4; EN50131-1; EN50136-2
Table 4 Technical Specifications: *) 350 mA for Grade 3 Control Panels connected to a Central Station; 500 mA in or-
der to comply with the T 031 standard, for ABS128M50,ABS128M75-G3,ABS48M50, and ABS18M35 control pan-
els, that must be connected to a Central Station; **) Supervised Premises Transceiver (Communicator) and Alarm
System.

14 Expandable Hybrid Control Panel

IDENTIFICATION OF PARTS
Read this section carefully to get an overall view of the
main components of the Control Panel.
The numbers in boldface (used in this text) refer to the
descriptions in the tables and figures in this section.
The components are generally numbered in clockwise
order. The outlined numbers refer to the common hard-
ware components of the devices and are described
once only — when first encountered.
+Figures 2 and 3 show the maximum configuration
of the ABSOLUTA Plus control panels, therefore,
some of the components may not be present on
your control panel.
N. DESCRIPTION
1Main board fixing holes
2Jumper to disable the activation of the Outputs
and Telephone Actions (Voice Calls, Voice Mes-
sages on AS100, Digital Calls and SMS):
= Actions Enabled (factory settings);
= Actions Disabled.
3Opening tamper switch connector
4Wall tamper switch connector
N. DESCRIPTION
5Holes to fit the IP Module
6Connector for the IP Module
7Holes to fit the GSM Module
8Connector for the GSM Module
9Microprocessor
10 RS232 Serial Port
11 Terminals for telephone line connection
12 Switching power Supply connector
13 Connector for backup Battery
14 Input terminals for detector connection
15 Programmable terminals as inputs or outputs
16 Terminals for transceiver connection
17 BPI BUS terminals for BPI peripheral connection
18 Terminals for Audio Station connection
19 Terminals for Tamper Line connection
20 Terminals for output device connection (Sirens,
etc.)
21 Diagnostic LED: see “Power connection” on
page 36
22 USB Serial Port for downloading/uploading on
USB pen and PC.
ABSOLUTA Plus IDENTIFICATION OF PARTS 15
12345 67 8 9 1 5 7 10 1
11
12
13
141516171819
22
20
11
21
Figure 1 ABSOLUTA Plus main board parts.

N. DESCRIPTION
Frontplate screws (2)
23 Surface Cable conduit entry
24 Wall tamper switch bracket
24a ABS-VAP11G Bridge WiFi
24b ABS-IP IP module
N. DESCRIPTION
25 Tamper switch
25a BGSM-100CA, Antenna with a magnetic base
and 25 cm cable
25b ABS-GSM, GSM Module
25c BGSM-100CA antenna cable
16 Expandable Hybrid Control Panel
AC/NFG+VGND
B+ L B– GND +V
AC/L
F3.15A/25ØV
F6.3A/25ØV
12345678
12345678
27
25c
23 24 25 24b 2625a 23
28
29
30
31
27
23
27
33
34
35
36
37
38
27
32
25b24a 43
Figure 2 Parts of the ABSOLUTA Plus in the metal box.

AC/NFG+VGND
B+
L
B–
GND
+V
AC/L
F 2A/25ØV
F6.3A/25ØV
1 2 3 4 5 6 7 8
27 61 24 39 26 36 27
27353227
29
30
40
31
38
37
25
37
38a 25b24b 39b39a61 62
24a 76
28
Figure 3 Parts of the ABSOLUTA Plus in the plastic box.
N. DESCRIPTION
26 Main Board (see Fig. 1)
27 Backplate anchor screw locations
28 Earth connection
29 Stranded wires: connect the Switching Power
Supply to the Main board
30 Cable for battery connection
31 Switching Power Supply
32 Thermal probe (accessory item)
33 Battery location
34 Location for second Input/Output Expander
N. DESCRIPTION
35 Main cable entry
36 Auxiliary cable entry
37 Wall tamper switch
38 Location for first Input/Output Expander
38a Bubble level
39 Hole for the antenna
39a ABS-AK GSM Antenna for plastic box
39b Connecting cable for the ABS-AK antenna
40 Cap to close the hole 39
ABSOLUTA Plus IDENTIFICATION OF PARTS 17

N. DESCRIPTION
41 Aperture for wall-tamper bracket
42 Two pivots for opening-tamper switch fixing
43 Hole for the GSM antenna wire
44 Five holes for Main Board fixing
45 Anchor for the GSM antenna wire
46 Hole for earth cable fixing
47 Anchor for the telephone line wires
48 Anchor for the power supply wires
49 Anchor for the battery wires on the Main Board side
50 Anchor for the Main wires on the BAW75T12
N. DESCRIPTION
51 Hole for BAW75T12 fixing
52 Anchor for the Main wires on BAW35T12 and
BAW50T12
53 Hole for BAW35T12 and BAW50T12 fixing
53a Hole for BAW35T12 fixing
54 Arrester for the Power Supplier
55 Anchor for the battery wires on the battery side
56 Four holes to fix the second M-IN/OUT
57 Two pivots for wall-tamper switch fixing
58 Four holes to fix the first M-IN/OUT
BAW75T12
BAW35T12
BAW50T12
27
23323
2727
35
36
57
27
41 454342 44 4642
47
48
49
50
52
53
54
58
56 51
55
53a
Figure 4 Mounting the Metal Box.

MOUNTING THE COMPONENTS
Mounting the Metal Box
Please read the following instructions, to get an overall
view of the steps involved in the control panel mounting
with the ABS-M Metal Box: refer to Figure 4 and Figure
2 on page 16.
Installing ABSOLUTA Plus Main Board
1. Insert the five reverse locking supports into the
holes 44 on the backplate.
2. Place the Main Board on the supports, then press it
down until blocks in its position.
3. Secure the Earth wire (Yellow-Green) eyelet to the
hole 46 on the backplate, by means the screw
M3x8 and washer.
4. Connect the other end of the earth wire (Yel-
low-Green) 28 to terminal -on the ABSOLUTA
Plus main board.
!The Main Board must be earthed in order to pro-
tect it from electrical surges from the Telephone
Line, and comply with Safety Regulations.
Installing the Power Supply You can install the
Switching Power Supply BAW35T12, BAW50T12 or
BAW75T12 into the Metal Box, as shown in Figure 2 on
page 16 (part nr. 31).
5. Cut the battery cables on the power supply.
+The backup battery must be connected to the con-
nector 13 on the Main Board. It can NOT be con-
nected directly to power supply.
6. BAW50T12/BAW75T12: slide the Power Supply
tab under the hook 54.
BAW35T12: screw a M3X8 screw on the hole 53a,
loosely, then slide the Power Supply tab in the
screw and tighten it.
7. Secure the BAW75T12 to the hole 51, the
BAW50T12 and the BAW35T12 to the hole 53,by
means the washer and screw (M3x8).
8. Insert the Power Supply plug into the connector 12
on the Main Board.
9. Secure the exceeding wires to the anchor 48 on the
backplate.
Installing the Tamper Switch You can install the
MAXIASNC switch (accessory item required to comply with
the EN50131-1 and EN50131-3 standards) to detect the box
opening, as shown in Figure 2 on page 16 (part nr. 25).
10. Secure the MAXIASNC switch to its location using
the two hexagonal nuts.
11. Connect the wire to the connector 3(T) on the Main
Board.
Installing the Wall-Tamper Switch You can install the
MAXIASNC switch (accessory item required to comply with
the EN50131-1 and EN50131-3 standards) to detect the box
removal, as shown in Figure 2 on page 16 (part nr. 37).
12. Place the Wall-Tamper Bracket 24 into the opening
41 on the backplate.
13. Secure the MAXIASNC switch to its location using
the two hexagonal nuts.
14. Connect the wire to the connector 4(S) on the Main
Board.
Installing the Input/Output Expander Module You
can install up to two Input/Output Expander Modules
M-IN/OUT into the Metal Box, as shown in Figure 2 on
page 16 (parts nr. 34 and 38).
15. Insert four reverse locking supports into the holes 58
and/or into the holes 56 on the backplate, depending
on if you are installing one and/or two Modules.
16. Place the Module PCB on the supports, then press
it down until blocks in its position.
17. Disable the tamper and wall-tamper contacts by in-
serting (closing) the jumper on the Input/Output Ex-
pander Module (TAMP DIS).
Marking Label Once you have assembled the compo-
nents, specify on the data label (which is located on the
outer right side of the box) the type of Control Panel that
you have constructed.
18. Using an indelible pen, tick the relevant box on the
Marking Label according to the following table.
ABS-M Power Supplies
Main Boards BAW35T12 BAW50T12 BAW75T12
ABS-18 ABS18M35 N/A N/A
ABS-48 ABS48M35 ABS48M50 ABS48M75
ABS-128 N/A ABS128M50 ABS128M75
ABSOLUTA Plus MOUNTING THE COMPONENTS 19

Mounting the Plastic Box
Please read the following instructions, to get an overall
view of the steps involved in the control panel mounting
with the ABS-P Plastic Box: refer to Figure 5 and Fig-
ure 3 on page 17.
eTo comply with the EN50131-1 and EN50131-3
standards, detach the cap 40 from the bottom, and
insert it into the hole 39.
Installing ABSOLUTA Plus Main Board
1. Slide the Main Board under the 2 tabs 67.
2. Secure the Main Board to the holes 60 on the
backplate using the two self tapping screws .
Installing BAQ15T12 Power Supply Read the fol-
lowing steps to install the BAQ15T12 Power Supply,
otherwise skip to “Installing BAW35T12 and
BAW50T12 Power Supply”.
3. Cut the battery cables on the power supply.
+The backup battery must be connected to the con-
nector 13 on the Main Board. It can NOT be con-
nected directly to power supply.
4. Using the 2 self tapping screws (3 x 8), secure the
BAQ15T12 to the holes 71 on the backplate..
5. Connect one end of the earth wire (Yellow-Green)
28 to the Earth terminal -on the ABSOLUTA Plus
mainr board, and the other to terminal Qon the
BAQ15T12 Switching Power Supply.
!The Main Board must be earthed in order to pro-
tect it from electrical surges from the Telephone
Line, and to comply with Safety Regulations.
6. Plug the Switching Power Supply into the connec-
tor 12 on the ABSOLUTA Plus Main Board.
Installing BAW35T12 and BAW50T12 Power Supply
Read the following steps to install the BAW35T12 or
BAW50T12 Power Supply or skip to “Installing the Tam-
per Switch”.
7. Cut the battery cables on the power supply.
+The backup battery must be connected to the con-
nector 13 on the Main Board. It can NOT be con-
nected directly to power supply.
8. BAW50T12: slide the Power Supply tab under the
hook 72.
BAW35T12: screw a self tapping screw 3 x 8 mm
on the hole 71, loosely, then slide the Power Supply
tab in the screw and tighten it.
9. Using the self tapping screw (3 x 8), secure the
power supply to the hole 75.
10. Connect one end of the Earth wire (Yellow-Green)
to terminal -on the ABSOLUTA Plus Main Board,
and the other to terminal Qon the BAQ35T12
Switching Power Supply.
!The Mother Main must be earthed in order to pro-
tect it from electrical surges from the Telephone
Line, and comply with Safety Regulations.
11. Insert the Switching Power Supply plug into the
connector 12 on the ABSOLUTA Plus Main Board.
Installing the Tamper Switch You can install the
MAXIASNC switch (accessory item required to comply
with the EN50131-1 and EN50131-3 standards) to de-
tect the box opening, as shown in Figure 3 on page 17
(part nr. 25).
12. Insert the MAXIASNC switch into its location.
13. Connect the wire to the connector 3(T) on the Main
Board.
Installing the Wall-Tamper Switch You can install
the MAXIASNC switch (accessory item required to
comply with the EN50131-1 and EN50131-3 standards)
to detect the box removal, as shown in Figure 3 on page
17 (part nr. 37).
14. Insert the MAXIASNC switch into its location.
15. Connect the wire to connector 4(S) on the Main
Board.
Installing the Input/Output Expander Module You
can install one Input/Output Expander Module
M-IN/OUT into the Plastic Box, as shown in Figure 3 on
page 17 (part nr. 38).
16. Slide the Module PCB under the tab 78.
17. Secure the PCB to the hole 79 on the backplate, us-
ing the self tapping screw.
18. Disable the tamper and wall-tamper contacts by in-
serting (closing) the jumper on the Input/Output Ex-
pander Module (TAMP DIS).
Marking Label Once you have assembled the compo-
nents, specify on the data label (which is located on the
battery holder shelf) the type of Control Panel that you
have constructed.
19. Using an indelible pen, tick the relevant box on the
Marking Label according to the following table.
ABS-P Power Supplies
Main Boards BAQ15T12 BAW35T12 BAW50T12
ABS-18 ABS18P15 ABS18P35 N/A
ABS-48 N/A ABS48P35 ABS48P50
ABS-128 N/A N/A ABS128P50
20 Expandable Hybrid Control Panel