Johnson Controls CIS01 Instruction Manual

P5415520
IMPORTANT:
READ AND UNDERSTAND
THIS MANUAL BEFORE
USING THIS CONTROLLER.
KEEP THIS MANUAL FOR
FUTURE REFERENCE.
Installation
&
Maintenance
Manual
Simplified Wired Controller
Model: CIS01

P5415520 1
TABLE OF CONTENTS
Important Notice ........................................................................................................................... 2
Product Inspection upon Arrival.................................................................................................... 2
1. Safety Summary ...................................................................................................................... 2
2. Brand Label.............................................................................................................................. 5
3. Installation Work....................................................................................................................... 5
4. Electrical Wiring ....................................................................................................................... 6
5. Checking Procedures............................................................................................................... 7
6 Function Selection and Input/Output Setting from Controller................................................... 8
7. Check Mode........................................................................................................................... 16
8. Reset of Controller ................................................................................................................. 16

2 P5415520
Important Notice
●Johnson Controls Inc. pursues a policy of continuing improvement in design and performance in its products.
As such, Johnson Controls Inc. reserves the right to make changes at any time without prior notice.
●Johnson Controls Inc. cannot anticipate every possible circumstance that might involve a potential hazard.
●This heat pump air conditioning unit is designed for standard air conditioning applications only.
Do not use this unit for anything other than the purposes for which it was intended for.
●The installer and system specialist shall safeguard against leakage in accordance with local pipefitter and
electrical codes. The following standards may be applicable, if local regulations are not available. International
Organization for Standardization: (ISO 5149 or European Standard, EN 378). No part of this manual may be
reproduced in any way without the expressed written consent of Johnson Controls Inc.
●This heat pump air conditioning unit is operated and serviced in the United States of America and comes with a full
complement of the appropriate Safety, Danger, and Caution, warnings.
●If you have questions, please contact your distributor or dealer.
●This manual provides common descriptions, basic and advanced information to maintain and service this heat
pump air conditioning unit which you operate as well for other models.
●This manual should be considered as a permanent part of the air conditioning equipment and should remain with
the air conditioning equipment.
Product Inspection upon Arrival
1. Upon receiving this product, inspect it for any damages incurred in transit. Claims for damage, either apparent or
concealed, should be filed immediately with the shipping company.
2. Check the model number, electrical characteristics (power supply, voltage, and frequency rating), and any
accessories to determine if they agree with the purchase order.
3. The standard utilization for this unit is explained in these instructions. Use of this equipment for purposes other
than what it designed for is not recommended.
4. Please contact your local agent or contractor as any issues involving installation, performance, or maintenance
arise. Liability does not cover defects originating from unauthorized modifications performed by a customer without
the written consent of Johnson Controls, Inc. Performing any mechanical alterations on this product without the
consent of the manufacturer will render your warranty null and void.
1. Safety Summary
Signal Words
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information considered important, but not hazard-related (for example,
messages relating to property damage).
General Precautions
To reduce the risk of serious injury or death, read these instructions thoroughly and
follow all warnings or cautions included in all manuals that accompanied the product and
are attached to the unit. Refer back to these safety instructions as needed.
●This system, including this controller, should be installed by personnel certified by Johnson Controls, Inc.
Personnel must be qualified according to local, state and national building and safety codes and regulations.
Incorrect installation could cause leaks, electric shock, fire or an explosion. In areas where Seismic Performance
requirements are specified, the appropriate measures should be taken during installation to guard against
possible damage or injury that might occur in an earthquake. If the unit is not installed appropriately correctly,
injuries may occur because of a falling unit.
●Use appropriate Personal Protective Equipment (PPE), such as gloves, protective goggles and electrical
protection equipment and tools suited for electrical operation purposes.

P5415520 3
●When transporting, be careful when picking up, moving and mounting these units. Although the controller may be
packed using plastic straps, do not use them for transporting from one location to another. Do not stand on or put
any material on the controller.
●When installing the controller cabling to the units, do not touch or adjust any safety devices inside the indoor or
outdoor units. All safety features, disengagement, and interlocks must be in place and functioning correctly before
the equipment is put into operation. If these devices are improperly adjusted or tampered with in any way, a serious
accident can occur. Never bypass, wire around, or jump-out any safety device or switch.
●Use only Johnson Controls recommended, provided as standardized, or replacement parts.
●Johnson Controls shall will not assume any liability for injuries or damage caused by not following steps outlined
or described in this manual. Unauthorized modifications to Johnson Controls products are prohibited as they…
◦May create hazards which could result in death, serious injury or equipment damage;
◦Will void product warranties;
◦May invalidate product regulatory certifications;
◦May violate OSHA standards;
Take the following precautions to reduce the risk of property damage.
●Do not touch the main circuit board or electronic components in the controller or remote devices.
Make sure that dust and/or steam does not accumulate on the circuit board.
●When installing the unit in a hospital or other facility where electromagnetic waves are generated from
nearby medical and/or electronic devices, be prepared for noise and electronic interference Electromagnetic
Interference (EMI). Do not install where the waves can directly radiate into the electrical box, controller
cable, or controller. Inverters, appliances, high-frequency medical equipment, and radio communications
equipment may cause the unit to malfunction. The operation of the unit may also adversely affect these
same devices. Install the unit at least 10 ft. (approximately 3m) away from such devices.
●Locate the controller at a distance of at least 3 ft. (approximately 1m) between the indoor unit and electric
lighting. Otherwise, the receiver part of the unit may have difficulty receiving operation commands.
●If the controller is installed in a location where electromagnetic radiation is generated, make sure that the
controller is shielded and cables are sleeved inside conduit tubing.
●If there is a source of electrical interference near the power source, install noise suppression equipment (filter).
●During the test run, check the unit’s operation temperature. If the unit is used in an environment where the
temperature exceeds the operation boundary, it may cause severe damage. Check the operation temperature
boundary in the manual. If there is no specified temperature, use the unit within the operation temperature
boundary of 35° to 104°F (0 to 40°C).
●Read this installation and maintenance manual for proper electrical wiring work.
Installation Precautions
Take the following precautions to reduce the risk of electric shock, fire or explosion
resulting in serious injury or death:
●If the remote sensors are not used with this controller, then do not install this controller…
▫In a room where there is no thermostat.
▫Where the unit is exposed to direct sunshine or direct light.
▫Where the unit is in close proximity to a heat source.
▫Where hot/cold air from the outdoors, or a draft from elsewhere (such as air vents, diffusers or grilles) can
affect air circulation.
▫In areas with poor air circulation and ventilation.
●Perform a test run using the controller to ensure normal operation. Safety guards, shields, barriers, covers, and
protective devices must be in place while the compressor/unit is operating. During the test run, keep fingers and
clothing away from any moving parts.
After installation work for the system has been completed, explain the “Safety Precautions,” use, and maintenance
of the unit to the customer according to the information in all manuals that accompanied the system. All manuals and
warranty information must be given to the user or left near the Indoor Unit.

4 P5415520
Electrical Precautions
Take the following precautions to reduce the risk of electric shock, fire or explosion
resulting in serious injury or death:
●Only use electrical protection equipment and tools suited for this installation.
●Insulate the controller against moisture and temperature extremes.
●Use specified cables between units and the controller.
●Communication cabling must be a minimum of 18-Gauge, 2-Conductor, Shielded Stranded Copper.
Shielded cable must be used in all areas to reduce the potential for communication errors.
When shielded cabling is applied, proper bonding and termination of the cable shield is required as per Johnson
Controls guidelines. Plenum and riser ratings for communication cables must be considered per application and
local code requirements.
●The polarity of the input terminals is important, so be sure to match the polarity when using contacts that have
polarity.
●Highly dangerous electrical voltages may be used in this system. Carefully refer to the wiring diagram and these
instructions when wiring. Improper connections and inadequate grounding can cause serious injury or death.
●Before installing the controller or remote devices, ensure that the indoor and outdoor unit operation has been
stopped. Further, be sure to wait at least five minutes before turning off the main power switch to the indoor or
outdoor units. Otherwise, water leakage or electrical breakdown may result.
●Do not open the service cover or access panel to the indoor or outdoor units without turning OFF the main
power supply. Before connecting or servicing the controller or cables to indoor or outdoor units, open and tag all
disconnect switches. Never assume electrical power is disconnected. Verify with a meter and equipment.
●Use an exclusive power supply at the controller’s rated voltage.
●Be sure to install circuit breakers (ground fault interrupter, isolating switch, molded case circuit breaker, and so
forth) with the specified capacity. Ensure that the wiring terminals are tightened securely to recommended torque
specifications.
●Clamp electrical wires securely with a cord clamp after all wiring is connected to the terminal block.
In addition, run wires securely through the wiring access channel.
●When installing the power lines, do not apply tension to the cables. Secure the suspended cables at regular
intervals, but not too tightly.
●Make sure that the terminals do not come into contact with the surface of the electrical box.
If the terminals are too close to the surface, it may lead to failures at the terminal connection.
●Do not clean with, or pour water into, the controller as it could cause electric shock and/or damage the unit.
Do not use strong detergent such as a solvent. Clean with a soft cloth.
●Verify that the ground wire is securely connected. Do not connect ground wiring to gas piping, water piping,
lighting conductor, or telephone ground wiring.

P5415520 5
A. When Exposing Controller Cable
3) Attach the controller to the holding bracket and connect the cable as follows.
B. When Using Steel Box
2. Brand Label
Check the boxes below as you complete each item.
Secure the holding bracket with the cable (accessory) onto the wall using 2-M4 screws (accessory).
Prepare steel box (option).
Secure the holding bracket (accessory) on the wall
with 2-M4 screws (field-supplied).
C. When Using a Table
1. Cut an installation hole to expose the controller as shown
in the figure at the right.
2. Prepare the bolts.
3. Place the bolts on the holding bracket and secure the
spacers with the nuts.
- Bolt (field-supplied)
- Nut (field-supplied)
- Spacer (field-supplied)
4. Remove the front decorative cover and attach the
controller using the installation hole.
NOTE:
Determine the bolt layout depending on the
spacers (field-supplied).
NOTE:
Allow a distance of more than 2 inches (50mm)
between spacer holes.
Implanted Steel Box
(Option, S size)
Screws
Nut (Field-Supplied)
Bolt
(Field-Supplied)
Bolt
Spacer
(Field-Supplied)
or more
Nut
(Field-Supplied)
Spacer
4-R2
2-3/8 inch (61mm)
3-1/4 inch (81mm)
5-1/2 inch (140mm)
1-1/4 inch
(30mm)
[3.3 Installation Procedures]
1) Remove the controller from the holding bracket.
3. Installation Work
[3.1 Selection of Installation Place]
1) Select a suitable place for handling and determine the installation place of the controller
with the customer’s acceptance. Do not install the controller in locations such as:
●where children can touch ●where the air from the air conditioner is directly discharged
[3.2 Before Installation]
1) This packing contains the following parts.
- Simplified Wired Controller Qty: 1 - for operation control
- Screw <M4x16L> Qty: 2 - for securing the holding bracket onto the wall.
- Cable with Connector 8 inches (20cm)
2) Connection of cable:
Connect the accessory cable to the field-supplied cable by
soldering. Insulate the connecting part with tape.
More than
2 inch
(50mm)
Connection Part
Field-Supplied Cable Accessory Cable
Select the accessory brand label according to the
production order.
Attach the accessory brand logo label to “This Area”.
This Area

6 P5415520
4. Electrical Wiring
4) Attach the controller to the holding bracket and connect the
cable as shown in the figure.
5) Attach the controller onto the holding bracket.
Begin by attaching the upper side, and then the lower side.
Max. 16 Indoor Units
Controller Electrical Box
of Indoor Unit
Electrical Box
of Indoor Unit
Terminal Board Terminal Board
M3.5
Screws
M3.5
Screws
Communication Cable with Shield Tube: 1P- AWG 18 (0.82mm2) or more
AA
BB
CN1
●Communication Cable (Field-Supplied)
*Option 1:
Communication Cable 2 × AWG 18 (0.82mm2)
(Maximum Total Length: 656.2 ft. (200m))
*Option 2:
Standard Communication Shielded Cable 2 × AWG 18
(0.82mm2)
connecting the shield to the ground at the electrical box
side.
(Maximum Total Length: 656.2 ft. (200m))
Insert the connector.
Push the cable through
the groove.
(Terminal Board
Side)
Solderless Terminal
(x type 1.25-3X)
(Controller Side)
(Terminal Board
Side)
(Controller Side)
2 inch (50mm)
2 inch (50mm)
4 inches (100mm)
4 inches (100mm)
ATTENTION:
Always make sure to turn off the power of the indoor unit when performing electrical wiring work. Performing electrical
wiring work with the power ON can damage the circuit boards of the indoor unit and the controller.
Communication cabling must be a minimum of 18-Gauge, 2-Conductor, Stranded Copper. Shielded cable must be
considered for applications and routing in areas of high EMI and other sources of potentially excessive electrical noise
to reduce the potential for communication errors. When shielded cabling is applied, proper bonding and termination
of the cable shield is required as per Johnson Controls guidelines. Plenum and riser ratings for communication
cables must be considered per application and local code requirements.
Wiring Example (Using communication cable with shield tube)

P5415520 7
A. Use AWG 22 (0.32mm2) to AWG 18 (0.82mm2) cable with a maximum total cable length 98.4 ft. (30m).
If the total cable length is longer than 98.4 ft. (30m), use communication cable of 1P to AWG 18 (0.82mm2)
Maximum total cable length 1640.5 ft. (500m). When using with the control timer, the maximum total cable length
is 328.1 ft. (100m).
Using other cables may cause a malfunction because of Electromagnetic Interference (EMI).
B. Maintain a distance of more than 12 inches (30cm) between the controller / indoor unit communication cables and
the power cables.
C. If installed within 12 inches (30cm), put the cables in a conduit tube and ground (type-D; ≤100Ω), one end of the
pipe. Without this procedure, malfunction or failure of the air conditioner because of EMI may occur.
D. When multiple indoor units are simultaneously controlled, set addresses for the refrigerant cycle and indoor units.
Specifically, when the indoor units from multiple refrigerant cycles are simultaneously controlled, a communication
issue may develop due to address duplication.
E. For more information about wiring controller-indoor units and setting indoor unit addresses, refer to “Unit No.
Setting” of each Installation and Maintenance Manual of indoor unit for details.
F. Do not leave any space at the cable opening of the remote controller case. If there is any space, cover it with,
for example, tape to avoid trouble caused by condensation or insects entering the controller case.
NOTICE
5. Checking Procedures
This controller is not equipped with the Test Run mode.
The test running must be performed from the outdoor units.
1. Turn ON the power for all indoor units.
2. Models with automatic addressing will take 3 to 5 minutes to complete the setting.
3. Set the Test Run mode from the outdoor units.
4. Cancellation the Test Run mode.
The Test Run mode can be canceled when:
- Test Run finishes automatically after 2 hours running time.
- Cancel Test Run from the outdoor units.
- Stop Test Run by pressing the On/Off switch at the controller.
The total number of the indoor units connected is
indicated on the temperature display.
NOTE:
Display indication
when one indoor unit is
connected.
If the indicated number of connected units is incorrect, any communication abnormality because of an incorrect wiring/
addressing or EMI issue may exist. In such a case, turn OFF the power supply and check the following.
(Do NOT repeat the ON/OFF operation at the main switch within 10 seconds).
(1) Indoor unit(s) power supply not turned ON, or incorrect wiring
(2) Incorrect wiring connection between indoor units or controllers
(3) Incorrect setting of rotary switch (overlapped setting)

8 P5415520
(1) Press and hold “ ” for “Temp” and “Fan” simultaneously
for at least 3 seconds during the normal mode (when unit
is not operated).
(2) Select the optional mode by pressing “ ” or “ ” for “Temp”
and press “Fan”.
(3) Select the indoor unit by pressing “ ” or “ ” for “Temp”
and press “Fan”.
(This screen is NOT displayed when there is only one
indoor unit connected with the controller.
In this case, (4) is displayed.)
Function Selection
(4) Press “ ” or “ ” for “Temp” and select the item.
(5) Press “Fan” and change the setting.
Input/Output Setting
(4) Press “ ” or “ ” for “Temp” and select the item.
(5) Press “Fan” and change the setting.
(6) Press “ ” and “ ” for “Temp” simultaneously to return to the normal mode.
6. Function Selection and Input/Output Setting from Controller
01: Function
Selection
02: Input/Output
Setting

P5415520 9
Table A Optional Setting Items for Function Selection
No. Items Optional Function Individual
Setting
Setting
Condition Contents Setting
1b1
Cancellation of Heating
Temperature Compensation
due to Uneven Heat Load
○
00
01
02
03
04
Standard (Set Temp. +7oF (+4oC))
Removal (Set Temp.)
Set Temp. +3oF (+2oC) (*1)
Set Temp. +5oF (+3oC)
Set Temp. +2oF (+1oC)
2b2
Circulator Function during
Heating Thermo-OFF ○00
01
Not Available
Available
3 b3 Not Prepared - - Not Used (Use as 00 setting conditions)
4 b4 Not Prepared - - Not Used
5 b5 Fixing of Operation Mode ×00
01
Standard
Fixed (Configured)
6 b6 Fixing of Setting Temperature ×00
01
Standard
Fixed (Configured)
7b7
Fixing of Operation as
Exclusive Cooling Unit ×00
01
Standard
Fixed (Configured)
8 b8 Automatic COOL/HEAT Operation ×00
01
Not Available
Available
9 b9 Fixing of Fan Speed ×00
01
Standard
Fixed (Configured)
10 bA Not Prepared - - Not Used
11 bb Cooling Temperature Compensation
due to Uneven Heat Load ×
00
01
02
Standard (No Compensation)
Set Temp. –2oF (–1oC)
Set Temp. –3oF (–2oC)
12 bC Not Prepared - - Not Used (Use as 00 setting conditions)
13 bd Not Prepared - - Not Used (Use as 00 setting conditions)
14 bE Not Prepared - - Not Used (Use as 00 setting conditions)
15 C1 Not Prepared - - Not Used (Use as 00 setting conditions)
16 C2 Not Prepared - - Not Used
17 C3 Not Prepared - - Not Used
18 C4 Not Prepared - - Not Used
19 C5
Hi Speed
(Except for Hi Speed during Heating
Thermo-OFF)
○
00
01
02
Not Available
Hi Speed 1 (*2)
Hi Speed 2
20 C6 Hi Speed during Heating Thermo-
OFF ○00
01
Not Available
Available
21 C7
Canceling of Enforced 3 Minutes
Minimum Operation Time of
Compressor
○00
01
Standard
Cancelation
22 C8 Thermistor of Wired Controller ○
00
01
02
00
01
02
< If Wired Controller Thermistor is Selected ˃
Not Available
Control by Thermistor of Wired Controller
Control by Average Value of Indoor Suction
Thermistor and Thermistor of Wired Controller
< If Remote Sensor is Selected ˃
Control by Average Value of Indoor Suction
Thermistor and Remote Sensor
Control by Remote Sensor
Same as "00"
23 C9 Not Prepared - - Not Used
24 CA Not Prepared - - Not Used
25 Cb Selection of Forced Stoppage Logic ○00
01
Forced Stoppage Input: A Contact
Forced Stoppage Input: B Contact
26 CC Not Prepared - - Not Used (Use as 00 setting conditions)
27 Cd Not Prepared - - Not Used (Use as 00 setting conditions)
28 CE Not Prepared - - Not Used (Use as 00 setting conditions)
29 CF Change of Louver Swing Angle ○
00
01
02
Standard (7-Step Operation)
Cold Draft Prevention
(5 Steps: lower 2 steps cut off)
High Ceiling (higher 2 steps cut off)
30 d1 Power Supply ON/OFF 1 ○00
01
Not Available
Available
31 d2 Not Prepared - - Not Used

10 P5415520
No. Items Optional Function Individual
Setting
Setting
Condition Contents Setting
32 d3 Power Supply ON/OFF 2 ○00
01
Not Available
Available
33 d4 Not Prepared - - Not Used (Use as 00 setting conditions)
34 d5 Prevention for Heating Discharge Air
Temp. Decrease ○00
01
Not Available
Available
35 d6 Not Prepared - - Not Used (Use as 00 setting conditions)
36 d7 Not Prepared - - Not Used
37 E1 Not Prepared - - Not Used (Use as 00 setting conditions)
38 E2 Not Prepared - - Not Used (Use as 00 setting conditions)
39 E3 Not Prepared - - Not Used (Use as 00 setting conditions)
40 E4 Not Prepared - - Not Used (Use as 00 setting conditions)
41 E5 Not Prepared - - Not Used (Use as 00 setting conditions)
42 E6 Indoor Fan Operation Time After
Cooling Operation Stoppage ○
00
01
02
Not Available
60 min.
120 min.
43 E7 Not Prepared - - Not Used (Use as 00 setting conditions)
44 E8 Fan Operation Control during
Heating Thermo-OFF ○00
01
Not Available (LOW)
SLOW
45 E9 Not Prepared - - Not Used (Use as 00 setting conditions)
46 EA Not Prepared - - Not Used (Use as 00 setting conditions)
47 Eb Fan Operation Control during
Cooling Thermo-OFF ○
00
01
02
Not Available
LOW
SLOW
48 EC Forced Thermo-ON Stoppage during
Cooling ○00
01
Not Available
Available
49 Ed Not Prepared - - Not Used (Use as 00 setting conditions)
50 EE Automatic Fan Speed Control ○00
01
Not Available
Available
51 EF Automatic Fan Speed Control
(High 2) ○00
01
Not Available
Available
52 F0 Not Prepared - - Not Used
53 F1 Automatic OFF Timer Setting
* Do not set the functions “0C”~“0F”
when 2 (two) wired controllers are
used in the same controller group.
×
00
01
02
•
•
23
24
0A
0B
0C
0D
0E
0F
No Function
OFF Timer by 1 hr
OFF Timer by 2 hrs
•
•
OFF Timer by 23 hrs
OFF Timer by 24 hrs
OFF Timer by 30 min.
OFF Timer by 90 min.
OFF Timer by 40 min.
OFF Timer by 45 min.
OFF Timer by 50 min.
OFF Timer by 55 min.
}
Do not set them when
two wired controllers
are used.
54 F2 Wired Controller Primary-Secondary
Setting ×00
01
Primary
Secondary
55 F3 Automatic Reset of Setting
Temperature (*3) ×00
01
Not Available
Available
56 F4 Automatic Reset Time ×
00
01
02
03
30 min. (Factory-Setting)
15 min.
60 min.
90 min.
57 F5 Automatic Reset Temperature
for Cooling (*4) ×
66 (19)
68 (20)
70 (21)
72 (22)
74 (23)
76 (24)
77 (25)
78 (26)
80 (27)
82 (28)
84 (29)
86 (30)
66oF (19oC)
68oF (20oC)
70oF (21oC)
72oF (22oC)
74oF (23oC)
76oF (24oC)
77oF (25oC) (Factory-Setting)
78oF (26oC)
80oF (27oC)
82oF (28oC)
84oF (29oC)
86oF (30oC)

P5415520 11
No. Items Optional Function Individual
Setting
Setting
Condition Contents Setting
58 F6 Automatic Reset Temperature
for Heating (*5) ×
62 (17)
64 (18)
66 (19)
68 (20)
70 (21)
72 (22)
74 (23)
76 (24)
77 (25)
78 (26)
80 (27)
82 (28)
84 (29)
86 (30)
62oF (17oC)
64oF (18oC)
66oF (19oC)
68oF (20oC)
70oF (21oC) (Factory-Setting)
72oF (22oC)
74oF (23oC)
76oF (24oC)
77oF (25oC)
78oF (26oC)
80oF (27oC)
82oF (28oC)
84oF (29oC)
86oF (30oC)
59 F7
Operation Stoppage Prevention by
Wired Controller Operational Error
(*6) ×00
01
Not Available
Available
60 F8 Not Prepared - - Not Used
61 F9 Not Prepared - - Not Used
62 FA Not Prepared - - Not Used
63 Fb Not Prepared - - Not Used
64 FC Cooling Lower Limit for Setting
Temperature (*4) ×
00
01
02
03
04
05
06
07
08
09
10
66oF (19oC)
68oF (20oC)
70oF (21oC)
72oF (22oC)
74oF (23oC)
76oF (24oC)
77oF (25oC)
78oF (26oC)
80oF (27oC)
82oF (28oC)
84oF (29oC)
65 Fd Heating Upper Limit for Setting
Temperature (*5) ×
00
01
02
03
04
05
06
07
08
09
10
11
12
86oF (30oC)
84oF (29oC)
82oF (28oC)
80oF (27oC)
78oF (26oC)
77oF (25oC)
76oF (24oC)
74oF (23oC)
72oF (22oC)
70oF (21oC)
68oF (20oC)
66oF (19oC)
64oF (18oC)
66 FE Not Prepared - - Not Used (Use as 00 setting conditions)
67 FF Not Prepared - - Not Used (Use as 00 setting conditions)
68 H1 Maintenance Alarm ×00
01
Show
Hide
69 H2 No Indication of Auto Control ×00
01
Show
Not Show
70 H3 Operation Mode Change Restriction
(*7) ×
00
01
02
Unlimited operation (Factory Setting)
Operation mode set by central control equipment
+ “Fan” mode
Operation mode change not available
(Hide operation mode)
71 H4 Not Prepared - - Not Used (Use as 00 setting conditions)
72 H5 Not Prepared - - Not Used (Use as 00 setting conditions)
73 H6 °F/°C Lock (*8) ×00
01
Lock
Unlock
74 J1 Not Prepared - - Not Used (Use as 00 setting conditions)
75 J2 Not Prepared - - Not Used
76 J3 Run Indicator Color ×00
01
Green
Red

12 P5415520
No. Items Optional Function Individual
Setting
Setting
Condition Contents Setting
77 J4 Remote Control Run/Stop
Prohibit by Central Controller (*9) ×
00
01
02
No Setting (Factory Default)
RC Run/Stop Operation Prohibited
RC Run Operation Prohibited
78 J5 Not Prepared - - Not Used (Use as 00 setting conditions)
79 J6 Not Prepared - - Not Used (Use as 00 setting conditions)
80 J7 Not Prepared - - Not Used (Use as 00 setting conditions)
81 J8 Eco-operation (*10) ×00
01
Not Available
Available
82 J9 Not Prepared - - Not Used (Use as 00 setting conditions)
83 JA Not Prepared - - Not Used (Use as 00 setting conditions)
84 Jb Not Prepared - - Not Used (Use as 00 setting conditions)
85 JC Calibration for Thermistor of Wired
Controller ×
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
0°F ( 0°C)
–1°F (–0.5°C)
–2°F (–1.0°C)
–3°F (–1.5°C)
–3°F (–2.0°C)
–4°F (–2.5°C)
–5°F (–3.0°C)
–6°F (–3.5°C)
+1°F (+0.5°C)
+2°F (+1.0°C)
+3°F (+1.5°C)
+3°F (+2.0°C)
+4°F (+2.5°C)
+5°F (+3.0°C)
+6°F (+3.5°C)
0°F ( 0°C)
86 K1 Not Prepared - - Not Used (Use as 00 setting conditions)
87 K2 Not Prepared - - Not Used (Use as 00 setting conditions)
88 K3 Not Prepared - - Not Used (Use as 00 setting conditions)
89 K4 Not Prepared - - Not Used (Use as 00 setting conditions)
90 K5 Motion Sensor Detection Level ○
00
01
02
Standard
High
Low
91 K6
Operation Setting during
Thermistor of Wired Controller
or Remote Sensor
○
00
01
02
03
ALL
COOL/DRY
HEAT
ALL
92 K7 Radiation Temperature Sensor
Calibration ○
00
01
02
03
Normal
Upper
Lower
Normal
93 K8
Control of Dew Condensation
Prevention
(Only for Mini Cassette Type)
○00
01
Not Available
Available
94 K9 Not Prepared - - Not Used (Use as 00 setting conditions)
95 KA Not Prepared - - Not Used (Use as 00 setting conditions)
96 L1 Setting Position of Motion Sensor ○
00
01
02
03
A
B
-
D
97 L2 Not Prepared - - Not Used (Use as 00 setting conditions)
98 L3
Louver Setting during Energy-Saving
Forced Thermo-OFF
(Only for Mini Cassette Type)
○
00
01
02
03
Recive Air: Low (Standard)
Recive Air: Medium
Recive Air: High
Not Available
99 L4 Fan Speed during Energy-Saving
Forced Thermo-OFF ○00
01
Not Available (Standard)
Available
100 L5 Louver Swing Operation
Energy-Saving Forced Thermo-OFF ○00
01
Not Available
Available

P5415520 13
No. Items Optional Function Individual
Setting
Setting
Condition Contents Setting
101 L6 Not Prepared - - Not Used (Use as 00 setting conditions)
102 L7 Not Prepared - - Not Used (Use as 00 setting conditions)
103 L8 Not Prepared - - Not Used (Use as 00 setting conditions)
104 L9 Auxiliary Heater at Defrosting
Operation ○00
01
ON
OFF
105 LA Not Prepared - - Not Used (Use as 00 setting conditions)
106 Lb Not Prepared - - Not Used (Use as 00 setting conditions)
107 P1 Setting Temperature ×00
01
Every 1oF (0.5oC)
Every 2oF (1oC)
108 P2 Not Prepared - - Not Used (Use as 00 setting conditions)
109 P3 Not Prepared - - Not Used (Use as 00 setting conditions)
110 P4 Not Prepared - - Not Used (Use as 00 setting conditions)
111 P5 Temperature While FAN Mode ×00
01
Show
Hide
112 P6 Not Prepared - - Not Used (Use as 00 setting conditions)
113 P7 Not Prepared - - Not Used (Use as 00 setting conditions)
114 P8 Not Prepared - - Not Used (Use as 00 setting conditions)
115 P9 Not Prepared - - Not Used (Use as 00 setting conditions)
116 PA Not Prepared - - Not Used (Use as 00 setting conditions)
117 Pb Not Prepared - - Not Used (Use as 00 setting conditions)
118 PC Not Prepared - - Not Used (Use as 00 setting conditions)
119 q1 Auxiliary Heater Setting ×00
01
Not Available
Available
120 q2 Auxiliary Heater ON Compensation ×
-3(-1.5)
-4(-2.5)
-5(-3.0)
-6(-3.5)
-7(-4.0)
-8(-4.5)
-9(-5.0)
-1(-0.5)
-2(-1.0)
-3oF (-1.5oC)
-4oF (-2.5oC)
-5oF (-3.0oC)
-6oF (-3.5oC)
-7oF (-4.0oC)
-8oF (-4.5oC)
-9oF (-5.0oC)
-1oF (-0.5oC)
-2oF (-1.0oC)
121 q3 Auxiliary Heater OFF Compensation ×0(0.0)
1(0.5)
0oF (0.0oC)
1oF (0.5oC)
122 q4 Ambient Temperature Restriction
Setpoint ×
-4
2
8
14
20
26
32
-13
-8
(-20.0)
(-17.0)
(-13.0)
(-10.0)
(- 7.0)
(- 3.0)
( 0.0)
(-25.0)
(-22.0)
-4oF (-20.0oC)
2oF (-17.0oC)
8oF (-13.0oC)
14oF (-10.0oC)
20oF (- 7.0oC)
26oF (- 3.0oC)
32oF ( 0.0oC)
-13oF (-25.0oC)
-8oF (-22.0oC)
123 q5 Ambient Temperature Restriction
Setpoint Compensation ×
4(2.5)
5(3.0)
6(3.5)
1(0.5)
2(1.0)
3(1.5)
4oF (2.5oC)
5oF (3.0oC)
6oF (3.5oC)
1oF (0.5oC)
2oF (1.0oC)
3oF (1.5oC)
124 q6 Not Prepared - - Not Used (Use as 00 setting conditions)
125 q7 Not Prepared - - Not Used (Use as 00 setting conditions)
126 q8 Not Prepared - - Not Used (Use as 00 setting conditions)
127 q9 Not Prepared - - Not Used (Use as 00 setting conditions)
128 qA Not Prepared - - Not Used (Use as 00 setting conditions)
129 qb Not Prepared - - Not Used (Use as 00 setting conditions)
130 qC Not Prepared - - Not Used (Use as 00 setting conditions)
131 qd Not Prepared - - Not Used (Use as 00 setting conditions)
132 r1 Dual Setpoint ×00
01
Not Available
Available

14 P5415520
(*1): The “02”, “03”, “04” settings may not be available depending on the type of indoor unit.
When connecting multiple indoor units, do separate settings.
(*2): If Duct type models, 00: Increasing fan speed 1 (standard), 01: Increasing fan speed 2 (high static pressure),
02: Standard (low static pressure).
(*3): If the set temperature is changed and kept within the set time at “F4”, the temperature is automatically changed to
“F5” and “F6”. (If the set temperature is out of range at “F5” and “F6”, it is applied within the upper and lower limits
for the set temperature.)
(*4): Applicable to the fan, cooling and dry operation modes.
(*5): Applicable to the heating operation mode.
(*6): Operation is stopped by pressing the “ ” (On/Off) button for 3 seconds.
(*7): “01” is available only when one controller is used. Do not use this setting when two (primary-secondary)
controllers are used.
(*8): Change the temperature unit (°F or °C) via the “ ” and “ ” (Temp switch). Push simultaneously after setting “01”
(Unlock) of this function (H6). Default is “°F”.
(*9) If the operation on the controller is locked by this function (J4), Run/Stop state cannot be changed even in the
emergency. Make sure that this lock will NOT cause any inconvenience.
(*10): When the unit is restarted by the controller, the temperature automatically changes to the setting temperature of
“F5” or “F6”.
NOTE:
1. Power on, wait 3 minutes and then change the optional setting.
2. When changing the “CF” setting (change of louver swing angle), restore the power supply or allow the louver to
make one complete swing fully in the auto-swing mode and then apply the optional setting.
3. The optional settings may be different according to the indoor and outdoor unit models.
Verify that the unit has the optional setting.
4. Record the setting conditions for each optional setting in the "Setting" column of the table below.
5. The above optional functions marked with an “X” at the individual setting can change the condition only when “All
Rooms” is set.
No. Items Optional Function Individual
Setting
Setting
Condition Contents Setting
133 r2 Cooling/Heating Changeover
Temperature ×
2(1.0)
3(1.5)
4(2.5)
5(3.0)
1(0.5)
2oF (1.0oC)
3oF (1.5oC)
4oF (2.5oC)
5oF (3.0oC)
1oF (0.5oC)
134 r3 Setback Temperature Compensation ×
4(2.5)
5(3.0)
6(3.5)
7(4.0)
8(4.5)
9(5.0)
10(5.5)
1(0.5)
2(1.0)
3(1.5)
4oF (2.5oC)
5oF (3.0oC)
6oF (3.5oC)
7oF (4.0oC)
8oF (4.5oC)
9oF (5.0oC)
10oF (5.5oC)
1oF (0.5oC)
2oF (1.0oC)
3oF (1.5oC)
135 r4 Not Prepared - - Not Used (Use as 00 setting conditions)
136 r5 Not Prepared - - Not Used (Use as 00 setting conditions)
137 r6 Not Prepared - - Not Used (Use as 00 setting conditions)
138 r7 Not Prepared - - Not Used (Use as 00 setting conditions)
139 r8 Not Prepared - - Not Used (Use as 00 setting conditions)
140 r9 Not Prepared - - Not Used (Use as 00 setting conditions)
141 rA Not Prepared - - Not Used (Use as 00 setting conditions)
142 rb Not Prepared - - Not Used (Use as 00 setting conditions)
143 S1 Not Prepared - - Not Used (Use as 00 setting conditions)
144 S2 Not Prepared - - Not Used (Use as 00 setting conditions)
145 S3 Not Prepared - - Not Used (Use as 00 setting conditions)
146 S4 Not Prepared - - Not Used (Use as 00 setting conditions)
147 S5 Not Prepared - - Not Used (Use as 00 setting conditions)
148 S6 Not Prepared - - Not Used (Use as 00 setting conditions)
149 S7 Not Prepared - - Not Used (Use as 00 setting conditions)
150 S8 Not Prepared - - Not Used (Use as 00 setting conditions)

P5415520 15
Table B Input and Output Number Display and Connectors
Table C Input and Output Settings and Display Codes
Input Number Display Port Factory Setting Setting
Input/Output Indication Setting Item Indication
Input 1 CN3 1-2 Remote ON/OFF 1 (Level) 03
Input 2 CN3 2-3 Prohibiting Remote Control after Manual Stoppage 06
Output 1 CN7 1-2 Operation 01
Output 2 CN7 1-3 Alarm 02
Output 3 CN8 1-2 Thermo-ON for Heating 06
Indication Input Output
00 Not set Not set
01 Room Thermostat (for Cooling) Operation
02 Room Thermostat (for Heating) Alarm
03 Remote ON/OFF 1 (Level) Cooling
04 Remote ON/OFF 2 (Operation) Thermo-ON for Cooling
05 Remote ON/OFF 2 (Stoppage) Heating
06 Forbidding Remote Control after Manual Stoppage Thermo-ON for Heating
07 Remote Cooling / Heating Change Not set
09 Setback Operation
NOTE:
* Power on, wait 3 minutes and then change the optional setting.
* Do not set the elevating grille for the total heat exchanger.
* Record the setting conditions for each input and output in the “Setting” column of the table.

16 P5415520
7. Check Mode
Check 1: Sensor condition of the air conditioner is monitored and indicated.
Check 2: Sensor data of the air conditioner prior to alarm occurrence is indicated.
(1) Press and hold “ ”, “ ” for “Temp” and “Fan”
simultaneously for at least 3 seconds during the normal
mode.
(3) Select the indoor unit by pressing “ ” or “ ” for “Temp”
and press “Fan”.
(2) Select the “Check” mode by pressing “ ” or “ ” for “Temp”
and press “Fan”.
(4) Press “ ” or “ ” for “Temp” and select the item.
(5) Press “ ” or “ ” for “Temp” simultaneously to return to
the normal mode.
01: Check 1
02: Check 2
NOTE:
The “check” items are different for each indoor unit type. Check the service manual for the indoor unit to be used
for the detailed information.
8. Reset of Controller
Reset the EEPROM inside the controller.
After resetting, shut off the indoor unit power supply.
After indication on the remote controller turns OFF, turn the power ON for indoor unit again.
(1) Press “ ” and “ ” for “Temp” and “Fan” simultaneously
during the normal mode (when unit is not operated).
(3) Reset EEPROM.
When the figure on the right is displayed, press “ ” for
“Temp” or leave it for 15 seconds, then EEPROM data
will be deleted.
(2) Press “ ” and “ ” for “Temp” and “Fan” simultaneously
again when the screen is switched as shown on the right.
(4) After a few seconds, the controller will restart automatically.

P5415520 17

P5415520-rev.3
© 2018 Johnson Controls, Inc.
LIT-12012037
Issued December, 2018