Johnson Controls VCC-64 User manual

User Manual: VCC-64
1 Rev.0.3
PAVA System
VCC-64
Volume and Channel Controller VCC-64
© 2019 Johnson Controls. All rights reserved. All specifications and other information shown were current as of
document revision date and are subject to change without notice. Tyco Fire & Security GmbH, Victor von Bruns-
Strasse 21, 8212 Neuhausen am Rheinfall, Switzerland

User Manual: VCC-64
2 Rev.0.3
SAFETY INSTRUCTIONS
Please read carefully these safety instructions.
•Keep this User Manual for future reference.
•Unplug the equipment from the AC before cleaning.
•Do not use liquid or sprayed detergent for cleaning.
•Use a cloth for cleaning.
•Do not expose this equipment to humidity.
•Install this equipment on a safe surface. If the equipment is not in a safe surface, it may
fall and become damaged.
•The openings on the enclosure are for air convection. Do not allow it to overheat. DO
NOT COVER THE OPENINGS.
•Place the power cord where people will not step or stumble. Do not place objects on the
power cord.
•Always observe all warnings and precautions indicated on the equipment.
•If the equipment is not used for several days, disconnect the power supply to prevent
damage from overloading. Never pour liquid into the openings, this could cause fire or
electric shock.
•Never open the equipment. For safety reasons, the equipment should only be opened
by qualified personnel.
•Pay attention to connection polarity when operating the machine with a power supply
(DC). Reverse connection polarity may cause damage to the equipment, or to the power
supply.
•Let staff check the equipment if any of these situations occur:
oThe power cord or power plug is damaged.
oLiquid has penetrated inside the equipment.
oThe equipment has been exposed to moisture.
oThe equipment does not work well or does not work according to the instruction
manual.
oThe equipment was dropped and damaged.
oIf the equipment has obvious signs of damage.
•Disconnect the audio inputs and outputs while making connections. Be sure to use
the proper cables to make the connections.

User Manual: VCC-64
3 Rev.0.3
Contents
1DESCRIPTION ................................................................................................................... 4
2FUNCTIONING................................................................................................................... 4
2.1.1 Rest Mode ............................................................................................................ 4
2.1.2 Active Mode .......................................................................................................... 5
2.1.3 Automatic Lock ..................................................................................................... 6
2.2 Connection to the System ............................................................................................ 6
2.2.1 Data Bus and Power Supply ................................................................................. 6
2.2.2 Bus Address ......................................................................................................... 7
2.2.3 Cabling ................................................................................................................. 7
3PROBLEM SOLVING:......................................................................................................... 8
3.1 Blank Screen ............................................................................................................... 8
3.2 The Number of Sources and Volume Does Not Appear on Screen .............................. 8
4MAINTENANCE INSTRUCTIONS ...................................................................................... 8
5TECHNICAL SPECIFICATIONS ......................................................................................... 9
6LIST OF ILLUSTRATIONS ................................................................................................. 9
7LIST OF TABLES................................................................................................................ 9

User Manual: VCC-64
4 Rev.0.3
1 DESCRIPTION
The VCC-64 allows up to 64 programmable channels and volume control (0-9). Usually installed
in local zones and connected via bus to the system, it offers source selection, volume control
and lock function.
FEATURES:
•Source selection (1-64)
•Volume setting for the zone (0-9) – 10 steps per change
•Automatic lock function
•It shows the identifier of the music source routed to the zone
•It shows the volume level assigned to the zone
•Lock activated indicator
•Connection of devices by bus mode
2 FUNCTIONING
The VCC-64 has a 2x8 character alphanumeric display where it shows the information related to
the zone of the PA system that is assigned.
2.1.1 Rest Mode
During the rest mode, the display will indicate the music source assigned to the zone, the
volume level (0-9) and the lock indicator.

User Manual: VCC-64
5 Rev.0.3
2.1.2 Active Mode
To unlock the device, press CH+ and then CH-. The lock indicator will disappear from the
display.
Once unlocked, press VOL+ to raise the volume level of the zone and VOL- to lower it. The
following table of equivalence shows the relationship between the volume indicated in the VCC-
64 and the gain associated to the zone.
VOLUME
GAIN
9 0δΒ
8
−3δΒ
7
−6δΒ
6
−10δΒ
5
−15δΒ
4
−21δΒ
3
−28δΒ
2
−36δΒ
1
−45δΒ
0
−100δΒ
Table 1 - Active Mode
To change the audio source assigned to the zone, press the buttons CH+ and CH-. The display
will show the change in the number of the source. The number displayed corresponds to the
number of the source in the PA system.
The audio source in the zone of the VCC-64 can be assigned remotely from the main PA
system's management or locally from the VCC-64.
The VCC-64 can select from any of the audio sources available in the system, up to 64. By
pressing CH+ or CH- we move from one to the next in a cyclic order.
The information relative to the audio sources that the VCC-64 will show, can be seen in the
following table.
DISPLAY
DESCRIPTION
Chxx (01-64) BGM Audio source No.XX
assigned to the zone
MIC LOCAL
A microphone is
broadcasting to the zone
Table 2 - Active Mode Display

User Manual: VCC-64
6 Rev.0.3
2.1.3 Automatic Lock
The VCC-64 has an automatic lock that will be activated after 25 seconds from the last push of
a button. To activate the VCC-64 again, press CH+ and then CH-. The lock indicator will
disappear from the display.
2.2 Connection to the System
Figure 1 - Connections
2.2.1 Data Bus and Power Supply
The VCC-64 has two poles for data connection through RS-485 protocol. It has a power supply
input of 12V DC with a consumption of 1.2W (100mA). The connector is marked as J500. When
the equipment has a power supply, the LED indicator marked power will be on.
The maximum number of units connected to the same interface is 8. The maximum length
(considering all sections) is 1000 m.
The connection uses a female Eurobock type connector (included) of 4 pins and 3.81mm pitch.
The range of cable section for each pole of this connector is 0.14 →1.5mm2(30 →14 AWG)

User Manual: VCC-64
7 Rev.0.3
Mark
Description
Type
Signal
Activation
G
Reference for power supply
(negative pole) Input
Connect to the negative pole of the
power supply.
12V Continuous power supply
(positive pole) Input
Connect to the negative pole of the
power supply (max 100 mA / 1.2V
dc).
D-
Serial connection port for
integration RS-485. Terminal D-
Port D- Standard RS-485/9600/8/SPACE/1
D+
Serial connection port for
integration RS-485. Terminal D+
Port D+ Standard RS-485/9600/8/SPACE/1
Table 3 - Connections
2.2.2 Bus Address
The VCC-63 has a DIP-Switch to configure the address in the RS-485 bus. Every controller
assigned to the same zone should have the same address configuration. For different zones
different address should be assigned.
Address
DIP-SWITCH
0
1
2
3
4
5
6
7
Table 4 - Bus Addresses
2.2.3 Cabling
The VCC-64 is connected to the system's interface through bus mode, and every VCC-64 will
be connected to each other. Only one VCC-64 has to be connected to the system's interface.

User Manual: VCC-64
8 Rev.0.3
The unit located closest to the system will be connected to the interface, and to the next VCC-
64. The last VCC-64 in the bus will not have any connection to a consecutive device.
Figure 2 - Cabling
3 PROBLEM SOLVING:
3.1 Blank Screen
If the display is blank, check the power supply. Verify that the wiring has been connected
according to chapter 2.2.1. If the power indicator light is on, reboot the system by disconnecting
the power and reconnecting it again. If, after restarting the system, nothing appears in the
screen then contact Technical Support of LDA.
If the power indicator is off, the device is not receiving power and therefore will not work
properly.
3.2 The Number of Sources and Volume Does Not Appear on Screen
If the number of sources and volume does not appear on screen, this is an indication to the
system that there is no connection. Restart the device by disconnecting the power and
reconnecting it again. If the problem persists and is not resolved, check the wiring as described
in section 2.2.
If, after performing these tests the problem persists, contact the support service of LDA.
4 MAINTENANCE INSTRUCTIONS
Generally, the equipment requires a reduced periodical maintenance.
The frequency of maintenance should be adjusted depending on the installation conditions of
the system.
Warning:
•Use only a soft, lint-free cloth to clean the system.
•Disconnect the device from any external power source.
•Disconnect all external devices.
•Keep it away from any liquid.

User Manual: VCC-64
9 Rev.0.3
•Do not use aerosol sprays, solvents or abrasives.
•Do not spray any cleaning products directly on the device.
Operation:
•Wipe the system with a damp cloth.
5 TECHNICAL SPECIFICATIONS
Model
VCC-64
Power supply
12V DC
Consumption
1.2W max (100mA)
Bus RS-485
Max. distance 1000m/ 3280,8 ft. (Max. 8 VCC-64 connected by
bus)
Address
Dip-switch 3 bit
Volume Buttons
VOL- / VOL+
Volume Steps
0-9
Source Buttons
CH+ / CH-
Channel Range
64 / 01 BGM + MIC LOCAL
Functioning Conditions
-5ºC to +45 ºC /23 ºF to 113 ªF
5% to 95% Relative Humidity (without condensation)
Finishing
ABS RAL 9016
Weight
110gr 3,88 oz
Drill Installation (HXWXD)
62mm x 70mmx 35mm / 2,44” x 2,75 x 1,38
Dimensions (HxWxD)
86mm x 86mm x45mm / 3,38 x 3,38 x 1,77
Table 5 - Technical Specification
6 LIST OF ILLUSTRATIONS
Figure 1 - Connections............................................................................................................... 6
Figure 2 - Cabling ...................................................................................................................... 8
7 LIST OF TABLES
Table 1 - Active Mode ................................................................................................................ 5
Table 2 - Active Mode Display.................................................................................................... 5
Table 3 - Connections................................................................................................................ 7
Table 4 - Bus Addresses............................................................................................................ 7
Table 5 - Technical Specification ............................................................................................... 9