Johnson Controls IQ Keypad-PG User manual

INSTALLATION MANUAL
IQ Keypad-PG
IQ Keypad Prox-PG
IQ Keypad is a battery powered, capacitive touch keypad for use with compatible IQ4 NS, IQ4 Hub & IQ Panel 4
platforms via the PowerG protocol. It provides an easy and intuitive interface to control basic features of the system.
This manual covers both IQ Keypad-PG and IQ Keypad Prox-PG models.

INTRODUCTION
ABOUT THIS GUIDE
QOLSYS CONFIDENTIAL AND PROPRIETARY
PAGE OF227
?
QUESTIONS?
Contact us at
[email protected]
INCLUDED IN BOX
SUPPORT
IQ Keypad
This document outlines the basic hardware specifications and software directions to install
and customize the IQ Keypad. Note that the information presented is not comprehensive,
but is specifically dedicated to those menus, features, and systems accessible solely to those
with the proper installation code. Features accessible to users and installers alike are outlined
in the IQ Keypad User Guide. The information contained is confidential and proprietary, and
is solely owned by Qolsys Inc. Any reproduction, modification or distribution without
permission is strictly prohibited. Reference to IQ Keypad throughout this manual covers both
models IQ Keypad-PG and IQ Keypad Prox-PG unless stated differently.
4 x AA
Batteries

Warning: This Product should be installed in accordance with the National Fire Alarm Code, ANSI/NFPA 72, (National Fire Protection Association,
Batterymarch Park,Quincy, MA 02269) and with National Electric Code, ANSI/NFPA 70. Printed information describing proper installation, operation,
testing, maintenance, evacuation planning, and repair service is to be provided with this Product. In Canada the product shall be installed in accordance with
the Standard for the Installation of Residential Fire Warning Systems, CAN/ULC-S540.
Warning: For Canadian installations this Product and all sensors associated with it (collectively, the “System”) should be tested once a week. The test shall be
performed also with primary DC power de-energized. For recommended smoke detectors maintenance instructions refer to user manual associated with
compatible Qolsys model QS5110-P840 smoke detector.
IQ KEYPAD
OVERVIEW

IQ KEYPAD OVERVIEW
EXTERIOR FRONT
QOLSYS CONFIDENTIAL AND PROPRIETARY
PAGE OF427
Prox Tag Reader
(IQ Keypad Prox-PG only)
Arm Stay
Arm Away
Arm Night
Trouble
LED
Armed Status LED
Disarmed Status
LED
Fire Emergency
(1+3)
Hold for 2 sec
Police Emergency
(7+9)
Hold for 2 sec
Aux Emergency
(4+6)
Hold for 2 sec

IQ KEYPAD OVERVIEW
EXTERIOR BACK
Retaining Screw
4 x AA Batteries
behind Back Plate
For UL2610 applications
this screw shall be used
for tamper protection
against mounting removal
Mounting
Holes
QOLSYS CONFIDENTIAL AND PROPRIETARY
PAGE OF527

INSTALLING
IQ KEYPAD

INSTALLING THE IQ KEYPAD
1. Mount the bracket to the
wall using appropriate
hardware ensuring it is level.
2. A screw shall be used in
this hole for UL2610
installations
WALL MOUNT
1
Note: For UL/ULC Commercial Burg installations (UL2610/ULC-S304 Security Level II compliant) use only wall mount option.
This product when installed as per these instructions does not present the risk of fire, electric shock, or injury to persons.
4
4. Slide the keypad down onto
the wall mount and secure with
the bottom screw so that it can
not be removed.
3. Insert the 4 x AA batteries in to the battery slots.
Be sure to observe correct polarity.
Use only Energizer AA 1.5V ALKALINE BATTERY
3
2
3
3
3
1

INSTALLING THE IQ KEYPAD
1. On the primary panel, start the “Auto Learn” process as indicated in the primary
panel manual (Settings/Advanced Settings/Installation/Devices/Security
Sensors/Auto Learn Sensor).
2. On the IQ Keypad press and hold [*] for 3 seconds to initiate pairing.
3. The IQ Keypad will be recognized by the primary panel. Configure options
accordingly then touch “Add New”.
QOLSYS CONFIDENTIAL AND PROPRIETARY
PAGE OF827
ENROLLING THE IQ KEYPAD
The IQ Keypad can be paired to either an IQ4 NS, IQ4 Hub or IQ Panel 4 running software version 4.4.0 or higher using the
PowerG protocol. Panels that do not have the PowerG daughter card installed will not support the IQ Keypad. Follow the
instructions below to pair an IQ Keypad to the primary panel:
NOTE: The IQ Keypad may also be manually paired to a panel by using the sensor ID printed on the
device beginning with 372-XXXX. If manual learn is used instead of Auto Learn, you must network the
device after pairing is complete by pressing and holding [*] for 3 seconds.

USER
INTERFACE

USER INTERFACE
QOLSYS CONFIDENTIAL AND PROPRIETARY
PAGE OF10 27
STATUS LIGHTS
KEYPAD STATUS LIGHTS:
Status lights help you understand the state of the system at a glance.
Status Lights
LED
Description
OFF
Not ready to Arm.
ON
Ready to Arm.
FLASHING
Ready to Arm, bypass-able zones are open.
OFF
Disarmed
ON
Armed
FLASHING
Alarm occurred
RAPID FLASHING
Bell silenced for Fire Alarms
OFF
No Trouble
ON
System Trouble
FLASHING
Keypad Low Battery