JohnsonSuisse Barossa Pivot Semi-frameless 900 User manual

INSTALLATION GUIDE
barossa
pivot - semi-frameless shower screen
• Immediately on receipt inspect the product for transit damage, missing packs/parts or manufacturing faults.
• Damage reported later cannot be accepted.
• Please handle the product with care avoiding knocks and shock loading to all sides and edges of glass.
• Damaged glass or missing parts will not be replaced under warranty if the installation process has begun.
• SAFETY GLASS CANNOT BE REWORKED, IF BROKEN IT HAS TO BE REPLACED
• Please read these instructions carefully before you start installation. Special care should be taken when drilling walls
to avoid hidden pipes or electrical cables.
• Securing into a stud or timber brace is highly recommended, if unable to do so, other secure means of xing must
then be considered.
This product is heavy and awkward to handle.
Two-person installation is recommended.
TOOLS REQUIRED
Model Door + Fixed Panel Set Return Panel Set
Barossa Pivot
Semi-frameless 900
KSSPV26CHP
Actual size 860-885mm
SSPV26CHR
Actual size 860-885mm
Barossa Pivot
Semi-frameless 1000
KSSPV40CHP
Actual size 960-985mm
SSPV40CHR
Actual size 960-985mm
Barossa Pivot
Semi-frameless 1220
KSSPV34CHP
Actual size 1180-1205mm -
These installation guidelines are for to the following shower screens:
IMPORTANT PRE-INSTALLATION NOTE:
1

INSTALLATION GUIDE
barossa
pivot - semi-frameless shower screen
ASSEMBLY COMPONENTS
2
20
1
2
3
4
5
7
8
9
10
11
12
13 14
15
16
17
19
6
18
1. 9 x Wall plugs
2. 8 x Flat screws M4x35
3. 8 x Screws M4x10
4. 8 x Screw cover caps
5. 2 x Wall posts
6. 2 x Fixed panels
7. 1 x Aluminium seal
8. 1 x Horizontal drip seal
9. 1 x Door Panel
10. 1 x Handle set
11. 2 x Magnetic seals
12. 1 x Bracket
13. 1 x Wall connector
14. 1 x Wall clip xing
15. 1 x Screw M4x35
16. 2 x Glass xings
17. 2 x Hinges
18. 1 x Vertical drip seal
19. 2 x Clips
20. 4 x Setting blocks
COMPONENT LIST

INSTALLATION GUIDE
barossa
pivot - semi-frameless shower screen
3
1
1
3
2
2
2
3
1
Corner to edge
of wall post
960-985
860-885
Corner to edge
of wall post
1180-1205
960-985
860-885
Flat screw
M4x35
View from inside
Before starting:
Ensure oor area for installation is completely level.
Walls must be plumb to within 5mm over the height of the screen.
Check-measure that the screen size shown on the packaging suits the intended installation area.
STEP 1
STEP 2

INSTALLATION GUIDE
barossa
pivot - semi-frameless shower screen
4
View from inside
Door Panel
Fixed Panel
Up
Down
STEP 3
STEP 4

INSTALLATION GUIDE
barossa
pivot - semi-frameless shower screen
5
1
2
34
2a 2b
3a 3b
1b
1a
4b 4c
4a
23
1
1
4
STEP 5
STEP 6

INSTALLATION GUIDE
barossa
pivot - semi-frameless shower screen
Bathroom Products Australia Pty Ltd
PO Box 728 Botany NSW 1455
Tel: [phone]
Fax: [phone]
www.johnsonsuisse.com.au
CARE INSTRUCTIONS
This shower screen has been treated with EnduroShield® easy-to-clean glass surface
treatment. Please follow the care instructions a󰀩xed to the door panel to ensure that your
treatment is long-lasting.
After use, your shower should be cleaned with mild detergent and water. This is particularly
important in hard water areas where insoluble lime salts may be deposited and allowed to
build up.
Cleaners of a abrasive/gritty nature should not be used. Care should be taken to avoid
contact with strong chemicals such as organic solvents and strippers. Glass cleaners can be
used but with caution. If in doubt please contact the manufacturer of the cleaner in question.
Please keep these instructions for aftercare and customer service details. 6
Ø3.2mm
Screw M4x10
View from inside
1c
1a
1b
STEP 7
STEP 8
Apply bathroom quality silicone sealant around all
external joints of the shower screen.
Sealant is not used on the inside of the screen as in
time water may build up within the wall jamb and then
leak out of the shower area. The screen is designed
to allow water to drain within the shower area.
ALLOW 24 HOURS BEFORE USING THE SHOWER