Jonix minimate User manual

minimate basic
USE AND MAINTENANCE MANUAL
AIR PURIFICATION DEVICE
AND ACTIVE SANITISATION OF INTERNAL COMPONENTS
WITH ADVANCED COLD PLASMA TECHNOLOGY

These instructions are the translation of the italian original ones. No liability is taken for translations into other languages that
do not conform to the original meaning. JONIX S.p.A. reserves every right concerning this manual, including the right to
make any necessary change or improvement to its products and to the manual at any time and without notice. It is forbidden
to reproduce in full or in part this manual without JONIX S.p.A.’s consent.

3- 64
minimate basic
TABLE OF CONTENTS
1 - GENERAL INFORMATION 5
1.1 - CE PLATE AND SERIAL NUMBER 5
1.2 - RESPONSIBILITY 5
1.3 - GENERAL SAFETY INDICATIONS, SYMBOLS AND DEFINITIONS 6
1.3.1 - General safety information 6
1.3.2 Symbols 6
1.3.3 - Definitions 7
2 - WARNINGS AND GENERAL PROHIBITIONS 8
2.1 - SAFETY SIGNS 11
3 - THE OPERATING SYSTEM 12
4 - TECHNICAL DATA JONIX minimate basic 14
4.1 - COMPONENTS DESCRIPTION JONIX minimate basic 14
4.1.1 - Technical characteristics JONIX minimate basic 15
4.1.2 - Spare parts available on order 15
5 - RECEPTION, TRANSPORT AND STORAGE 16
5.1 - PACKAGING 16
5.2 - HANDLING AND TRANSPORT 17
5.3 - INSPECTION UPON RECEPTION 17
5.4 - STORAGE 17
6 - INSTALLATION AND COMMISSIONING 18
6.1 - SAFETY INSTRUCTIONS 18
6.2 - GETTING STARTED 20
6.3 - OPERATING SITE CHARACTERISTICS 23
6.3.1 - Position of the operator 24
6.4 - ELECTRICAL CONNECTIONS 25
6.5 - ELECTRIC POWER SUPPLY 25
6.6 - USING THE DEVICE 25
6.7 - DEFAULT SETTINGS 26
6.7.1 - First start checks 26
6.8 - USER INTERFACE AND MENU NAVIGATION 27
6.8.1 - Main screen 27
6.8.2 - Switching the device on/off 28
6.8.3 - Screen lock and settings 30
6.8.4 - User login / user logout 31
6.8.5 - Filter ionising module screen 32
6.8.6 - Filters screen 33
6.8.7 - Fan screen 34
6.8.8 - Settings screen 35
6.8.8.1 - Date and time 36
6.8.8.2 - Language 36
6.8.8.3 - Display brightness 37
6.8.8.4 - Protection 37
6.8.8.5 - Accessing the time slots 38
6.8.8.5.1 - Time slots 39

4- 64
minimate basic
Thank you purchasing the JONIX minimate basic device.
This manual contains the information and anything deemed necessary for the transport,
installation, use and maintenance of the active sanitizing and air purification device JONIX
minimate basic.
Improper installation of the device and/or failure to comply with the instructions in this manual,
may void the warranty that the Manufacturer issues for its products.
The Manufacturer is not liable for any direct and/or indirect damage caused by incorrect installation
or damage caused by units installed by inexperienced and/or unauthorised staff. At the time of
purchase, check that the device is intact and complete.
The Manufacturer declines any liability in case of personal injury or property damage resulting
from any improper use of the device or from the failure to observe the use and safety instructions
specified in this manual. In any such case, any warranty claim will be void.
Any complaints must be submitted in writing within 8 days of receiving the goods.
6.8.8.6 - Recording of maintenance 40
6.8.7.6.1 - Filter ionising maintenance recording 41
6.8.8.6.2 - Filter maintenance recording 42
6.8.8.7 - Alarms history 43
6.8.8.8 - Configuration 43
6.8.9 - Operation display viewing 44
6.8.9.1 - Filter ioniser function 44
6.8.10 - Alarm status notifications 45
7 - MAINTENANCE 47
7.1 - WARNINGS 47
7.2 - ROUTINE MAINTENANCE 47
7.2.1 - Replacing Filters 48
7.2.2 - External cleaning of the device 50
7.2.3 - Ionising pipe cleaning 51
7.2.4 - Replacing the ionising pipe 55
7.3 - SPECIAL MAINTENANCE 59
8 - OPERATIONAL CHECK AND TROUBLESHOOTING (DIAGNOSTICS) 59
8.1 - DIAGNOSTICS 59
8.2 - GENERAL DIAGNOSTIC PROVISIONS 60
9 - DISPOSAL 61
EC DECLARATION OF CONFORMITY 62

5- 64
minimate basic
Fabbricante / Manufacturer JONIX S.p.A. S.B.
JONIX minimate basic
Viale Spagna, 31/33
35020 Tribano (PD)
Nome del prodotto / Product
name
Descrizione del prodotto /
Product description
Dispositivo per la sanificazione e purificazione
dell’aria
Codice prodotto /
Model 70MMBASICF1H13
Numero di serie /
Serial number 000000029704
Caratteristiche elettriche
Alimentazione / Power Supply 230V / 1~/ 50Hz
Potenza nominale Assorbita /
Power Consumption (W) 580
Corrente nominale / rated corrent
ampere (A) 2,5
Dimensioni
(LxPxH) [mm] 560x460x1060
Peso (kg) 71
Anno di produzione 2021
REF
SN
1.2 RESPONSIBILITY
Failure to comply with the instructions contained in this Use and Maintenance Manual releases
JONIX S.p.A. from any liability. For any data not included or not deducible from the following
pages it is recommended to consult JONIX S.p.A. directly.
JONIX S.p.A. Benefit Corporation
Viale Spagna 31/33
35020 Tribano - PD - Italy
http://www.jonixair.com
In particular, if the maintenance of the device is carried out in a manner that does not comply with
the instructions provided, or in any case in such a way as to compromise its integrity or modify
its characteristics, JONIX S.p.A. will be relieved of any responsibility regarding the safety of
persons, property, animals and the faulty operation of the devices.
The device described in this manual is provided with a
nameplate identifying it.
IMPORTANT WARNING
The JONIX minimate basic device is designed and made to sanitise the air in residential
and industrial processing environments that are incompatible with toxic and
flammable gases. It is therefore strictly forbidden to use the device in environments
where the air is mixed with and/or altered by other gaseous compounds and/or solid
particles. Using the device for purposes other than those intended and that do not
comply with those described in this manual will immediately relieve Manufacturer
and its distributors from any direct and/or indirect liability.
1 - GENERAL INFORMATION
1.1 CE PLATE AND SERIAL NUMBER
FAC-SIMILE

6- 64
minimate basic
OBLIGATION TO USE PROTECTIVE GLOVES
Use adequate hand protection in addition to other personal protective equipment
suitable for the place and the operations to be carried out.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.
The crossed-out bin symbol on the label on the appliance indicates that this product
complies with the regulations on waste electrical and electronic equipment. The
abandonment of the equipment in the environment or its unauthorised disposal is
punishable by law.
HIGH VOLTAGE HAZARD!
Do not open or remove any doors or protections before disconnecting the voltage
supply.
OBLIGATION: This symbol draws attention to a specific obligation or action to be
implemented with obligation.
FORBIDDEN: This symbol refers to operations that must be avoided under any
circumstances, and hence forbidden.
WARNING: It refers to integrations or suggestions concerning the proper use of the
device.
HAZARD: It refers to dangerous situations that may result from the use of the device, in
order to ensure personal safety.
1.3.2 Symbols
Please pay utmost attention to the following symbols and their meaning. They emphasise specific
information, such as:
1.3.1 General safety instructions
Any intervention, of whatever nature, on the device must be carried out by prior and careful
reading of this manual in all its parts, with particular reference to SAFETY.
It is essential, therefore, that the device is used in accordance with its intended use and with
this manual. This manual has been drawn up to provide the necessary information for personnel
dedicated to the use and maintenance of the device, until its sale or disposal. It must therefore
always be available to the staff who, before carrying out any operation on the device, must read
and assimilate all the information contained therein.
1.3 GENERAL SAFETY INSTRUCTIONS, SYMBOLS AND DEFINITIONS

7- 64
minimate basic
1.3.3 Definitions
Below are the definitions of the main terms used in the user manual.
MANUFACTURER
Individual or juridical person who designs and/or manufactures the device and is responsible
for its conformity for the purpose of placing it on the market under his own name or trademark.
SUPPLIER
Any professional operator in the marketing chain.
USER
Person, organisation or company who or which has purchased or rented the device and is going
to use it for the intended purposes.
USER/OPERATOR
Individual who has been authorised by the user to operate the device.
QUALIFIED STAFF
Individuals who, on the basis of their professional training, experience, knowledge of relevant
regulations and accident prevention regulations, are able to assess the work entrusted to them
and recognize and avoid any hazards.
AUTHORIZED PERSONNEL
Specialised personnel, assigned by the user to carry out certain tasks.
HAZARD
Source of possible injury or damage to health and safety.
RISK
Combination of probability and severity of possible injury or damage to health and safety in a
hazardous situation.
DANGEROUS ZONE
Any area within and/or close to a machine in which a person is exposed to a risk.
PROTECTIONS
Safety measures consisting of the use of specific technical means (guards and safety devices) to
protect users, users and operators from hazards.
REPAIR
Element of a machine used specifically to provide protection by means of a physical barrier;
depending on its construction, it may be called a headphone, cover, screen, door, fence, casing,
segregation, etc.
PROTECTIVE DEVICE
Device (other than a guard) that eliminates or reduces the risk; it can be used alone or associated
with a guard.

8- 64
minimate basic
READ THE INSTRUCTIONS BEFORE ANY OPERATION
Before starting any operation, it is mandatory to read this manual and apply all its
instructions.
The user must carefully read ALL the contents of this User and Maintenance Manual
and have it read by the designated users and maintenance technicians, for the parts
that are their responsibility.
2 - WARNINGS AND GENERAL PROHIBITIONS
It is the user's responsibility to ensure that, if this document is modified by JONIX
S.p.A., only the updated versions of the Manual are actually present at the points
of use.
Repair or unscheduled maintenance work must be carried out by personnel
authorised by JONIX S.p.A. or by qualified personnel in accordance with this use
and maintenance manual. Do not alter or tamper with the device as it can lead to
hazards and the manufacturer shall not be liable for any damage caused.
This Use and Maintenance Manual is an integral part of the device and must
therefore be kept with care and must ALWAYS accompany the device even if it
is transferred to another owner or user or transferred to another facility. In case
of damage or loss, request another copy from JONIX S.p.A. or download the
document from www.jonixair.com.
ROUTINE MAINTENANCE
Type of maintenance interventions during the life cycle, suitable for:
- maintain the original integrity of the goods;
- maintain or restore the efficiency of the goods;
- contain the normal degradation of use;
- ensure the useful life of the goods;
- cope with accidental events.
SPECIAL MAINTENANCE
Type of non-recurring and high cost interventions, compared to the replacement value of the
goods and the annual cost of routine maintenance of the same.
NON THERMAL PLASMA GENERATOR NTP (Non Thermal Plasma) or IONIZING TUBE
Electric field generator that transforms gas into plasma with high chemical oxidation power able
to oxidize and break down pollutants, bacteria, moulds, viruses and odours.

9- 64
minimate basic
It is forbidden to use the device outdoors or on wet surfaces. Do not expose to
water, rain or weathering.
It is forbidden to spray or throw water or other liquids directly inside the device,
even in case of fire.
It is forbidden to get on and/or sit on the device. It is forbidden to place objects,
animals or people on the device.
Do not pull, detach or twist the electrical wires coming out of the device, even when
it is disconnected from the mains.
It is forbidden to modify the safety and/or adjustment devices.
This device is not a toy, make sure it is placed out of the reach of children and take
precautions so that children do not play with the device.
Any maintenance or cleaning operation before disconnecting the device from the
power supply is prohibited.
Do not touch the device if you are barefoot and with parts of the body that are wet
or damp.
Cleaning and maintenance intended to be carried out by the user must not be
carried out by unsupervised children.
This device is not intended for use by people with reduced physical, mental or
sensory abilities or lack of experience and knowledge.
Any liability of JONIX S.p.A. is excluded for damage caused to persons, animals
or property, whether due to transportation, installation, adjustment, maintenance,
decommissioning or misuse.
The transport, handling, installation, commissioning and decommissioning of
this product must only be performed in accordance with the requirements and
instructions specified in this manual.
Please note that the use of products that require electricity involves the observance of some
crucial safety rules such as:

10 - 64
minimate basic
It is forbidden to open the access panels to the internal parts of the unit without
removing the power supply and making sure that the unit cannot be accidentally
powered.
It is forbidden to use the device with a damaged cable or plug.
It is forbidden to use the device if it does not work properly, has received a strong
blow, has been accidentally dropped, has been damaged or left outdoors or has
fallen into water.
It is forbidden to insert objects into the openings of the device.
Do not dispose of or leave the packaging material within reach of children because
it can be potentially dangerous.
For all maintenance operations it is good practice to use work gloves to protect
your hands.
• It is the duty of the user to perform all the maintenance operations on the device reported in
this manual.
• If a malfunction not indicated in this manual occurs, disconnect the power supply to the device
and consult your dealer and/or JONIX S.p.A..
• Only trained and qualified personnel can perform maintenance operations other than those
specified in this manual.
ATTENTION!
BEFORE CARRYING OUT ANY MAINTENANCE OPERATION MAKE SURE THAT
THE DEVICE IS NOT AND CANNOT ACCIDENTALLY BE POWERED ELECTRICALLY.
YOU MUST THEREFORE UNPLUG THE DEVICE BEFORE CARRYING OUT ANY
MAINTENANCE.
• When servicing the filters, pay particular attention to your fingers to avoid the risk of pinching.
• Clean the ionising tubes every time it is shown on the display.
• Do not put back the mesh on the ionising tube if it is even partially wet.
• Check that the earthing spring is in contact with the outer mesh once the ionising tube have
been screwed back into place. Otherwise contact the manufacturer.
• Do not use liquid cleaners, sprays, soap or other products directly on the device.
• Pay particular attention to the air passage grilles: check that they are clean to ensure the
passage of air.
For the maintenance and cleaning operations (see chapter 7 "Maintenance") of the device we
remind you that:

11 - 64
minimate basic
Pictogram 1 Pictogram 2 Pictogram 3 Pictogram 4 Pictogram 5
ELECTRICAL
VOLTAGE HAZARD
OBLIGATION TO
READ THE
INSTRUCTION
MANUAL
OBLIGATION TO
DISCONNECT
VOLTAGE BEFORE
MAINTENANCE
OBLIGATORY USE
OF PROTECTIVE
GLOVES
MOVING PARTS
HAZARD
2.1 SAFETY SIGNS
Check the condition of the safety pictograms periodically and replace them if necessary. The
safety signs on the machine are as follows:
Pictogram 5
Pictogram 2
Pictogram 4
Pictogram 1
Pictogram 3
Pictogram 5
Pictogram 1

12 - 64
minimate basic
e+
ion+
ion
R
3 - THE OPERATING SYSTEM
The range JONIX minimate consists of a variety of models to satisfy all air purification needs.
Immediately operational, it does not require any complex operation for its installation. Compact,
portable and silent, JONIX minimate basic is equipped with an advanced control system that
allows adjustment of the ventilation for a quick and effective response to the need for filtration and
particulate reduction and removal.
JONIX minimate basic:
• constantly reduces and eliminates bacterial loads in the air and on indoor surfaces;
• constantly decomposes volatile organic compounds (VOCs);
• it eliminates odours;
• is suitable for environments that need to reduce air contamination.
This sanitizing device, exploiting the physical phenomenon of ionization, promotes the controlled
formation of particular electrically charged species in the air through an electrostatic field. The
latter simulates a natural process that normally occurs through solar radiation, mechanically or
by other physical phenomena.
The particular ionic species produced are proven to be particularly effective as sanitizing agents
in air and on surfaces, moreover they are scientifically and historically proven to be beneficial on
people, especially the negatively electrically charged species (i.e. those derived from single or
small groups of molecules receiving an electron).
Electrical
field
< 3000W
Gas Molecule
[ O2, O3, NO, NO2 ]
Neutral Molecule
[ O2, CO2, H2O ]
[ H20, O3, VOC ]
Free
electron
Negative ion
stable
[O, O2, O3]
[ OH, HO2, HO2- •]
Free
radical
FUNGI
BACTERIA
MOULDS AND
YEASTS
M
I
C
R
O
B
I
C
I
D
E
A
C
T
I
O
N
Staphilococcus
Aureus
Aspergillus
Niger
Saccharomyces
Cerevisiae

13 - 64
minimate basic
The device JONIX minimate basic is equipped with two filtration stages. The medium filter
F7 combined with the absolute filter H13 or H14 allow the reduction of airborne fine dusts and to
ensure a very high degree of filtration.
The JONIX minimate basic also combines filtration with non-thermal plasma technology for
sanitisation of the internal components of devices.
The activity of air purification and sanitisation of the internal components of the JONIX
minimate basic device is compatible with the presence of persons and animals. No chemicals
are used and no harmful residual substances are generated.

14 - 64
minimate basic
1
12
14
5
2
6
3
10
5
6
9
11
4
7
5
5
18
19
13
11
9
8
16
4
17
15
4 - TECHNICAL DATA JONIX minimate basic
4.1 COMPONENT DESCRIPTION JONIX minimate basic
1 Display Touch screen
2 Flat Plug Power Socket Inlets with On/Off Rocker Switch
3 Power cable
4 Swivel casters with brake
5 Pressure outlets
6 Maintenance access front panel closures
7 Key to access the front panel
8 Maintenance access door
9 Filter fixing brackets
10 Magnetothermic switches for fan power supply
disconnection (Q1) and auxiliary power supply
disconnection (Q2)
11 Access door opening switch button for
maintenance
12 Adjustable 2 way air outlet register
13 Absolute filter H13 or H14
14 Centrifugal fun
15 Front panel for access to the fan
16 Thin particulate filter F7
17 Lower suction grille
18 1 ionising pipe ground securing bracket
19 1 ionising pipe for sanitisation of the ele-
ments inside the device
Fig. 1

15 - 64
minimate basic
4.1.1 Technical features JONIX minimate basic
The technical characteristics and relevant data are shown on the nameplate together with the
serial number identifying the device.
4.1.2 Spare parts available on order
Code Description Notes
JX70000006 F7 Filter -
JX70000016 H13 Filter For product with code
70MMBASICF H13.
JX70000017 H14 Filter For product with code
70MMBASICF H14.
70CONDTIPO175 175 IONISING PIPE REPLACEMENT No. 1 175 ionising pipe.
JX55000118 KEY TO OPEN THE
ACCESS MAINTENANCE DOOR -
Model
Dimensions
(L x P x H)
[mm]
Power
supply
Max power
absorption
[W]
Weight
[kg]
(*) Flow
rate treated
air [m3/h]
Degree
of
Protection
JONIX
minimate
basic
560 x 480 x 1060 230 V / 1~ / 50Hz 580 71 1200 IP40
(*): Default settings.

16 - 64
minimate basic
Fig. 2
5 - RECEPTION, TRANSPORT AND STORAGE
The JONIX minimate basic device is shipped in special protective packaging that must be
kept intact until installation. The materials that were not installed for technical requirements are
supplied with suitable enclosure secured to the inside or outside of the device itself.
The package includes:
- JONIX minimate basic.
- no. 1 ionising pipe (for sanitisation of the internal elements).
- Power cord.
- 2 keys for opening of the front access panel for maintenance.
- Operating and maintenance manual.
- Declaration of CE Conformity.
- Warranty Terms and Conditions.
5.1 PACKAGING

17 - 64
minimate basic
To handle the device, use appropriate means, in good condition and suitable
capacity, depending on the weight, as required by Directive 89/391/EEC and
subsequent amendments.
The carrier is responsible for securing the load on the means of transport.
JONIX S.p.A. declines any responsibility in case of damage caused by loads
poorly transported by the carrier.
Unless otherwise agreed in writing in advance, no other material or goods shall be placed on top
of the devices.
5.2 HANDLING AND TRANSPORT
Please take great care while unloading and positioning the devices, to prevent
damaging the casing or components. Always make sure that the load is stable.
Avoid uncontrolled rotations. Lifting assistance must, if necessary, be carried out
with rods, levers, grappling hooks without ever using hands alone.
During lifting and/or transport and/or handling operations, provide for appropriate
signalling and confinement of the dangerous zone, signalling the prohibition of
access to the dangerous zone by unauthorised personnel.
In case of prolonged storage before installation, the device must be protected from
dust, weather and kept away from heat and vibration. Do not allow the device to
come into contact with corrosive substances.
JONIX S.p.A. declines all liability for damage due to poor handling, transportation and
storage.
5.4 STORAGE
Any type of complaint must be sent in writing within eight days from receiving the
goods.
When you receive the device please check all its parts, in order to make sure that it has not been
damaged during transport.
Any damage must be reported to the carrier, by filling in the relevant section on the delivery note
and specifying the type of damage.
5.3 INSPECTION UPON RECEPTION

18 - 64
minimate basic
• The device must be installed in strict accordance with the instructions contained in this
manual.
• While performing installation, operate in full safety and in a clean environment clear of
obstructions.
• Before switching the device on check the integrity of the various components and of the
electrical mains to which it is connected, making sure that it is fitted with a circuit breaker
upstream of the power line.
• Before putting the device into operation, check that the electrical system to which it is to
be connected has an effective earthing system.
• Do not service or clean the device without first unplugging it from the mains.
• Perform routine maintenance following the instructions in this manual or contact JONIX
S.p.A. for assistance.
• Unscheduled maintenance and the replacement of damaged or worn parts must only be
carried out by specialist personnel authorised by JONIX S.p.A..
• Spare parts must meet the requirements defined by JONIX S.p.A..
• Do not insert objects of any kind into the device, as coming into contact with live parts or
electrical terminals may cause fires or electric shocks. In case of maintenance, check that you
have removed all tools and objects before closing the panels and restarting the device.
• Comply with the laws in force in the country in which the device is installed, regarding the use
and disposal of the packaging and products used for cleaning and servicing the device; you
should also observe the recommendations given by the manufacturers of such products.
• In the event of decommissioning or disposing of the MIC device, follow the anti-pollution
regulations set out by the country in which the device is installed.
• Use only the power supply indicated on the nameplate. If you are not sure about the type of
power supply available, ask your local retailer or electricity provider for assistance.
• Do not spill water or other liquids on the device.
• Place the device so that the power cable cannot be stepped on and/or does not cause tripping.
• Do not touch the inside of the device, unless otherwise specified in the instructions contained
in this manual.
• Never force the components when installing or performing maintenance operations: although
it is built with high strength materials, the parts of the device can be damaged if handled
incorrectly.
6.1 SAFETY INSTRUCTIONS
JONIX S.p.A. disclaims any liability for failure to comply with the safety and
prevention standards as described below.
The Manufacturer also disclaims any liability for damage caused by improper use
of devices and/or alterations carried out without prior authorisation.
6 - INSTALLATION AND COMMISSIONING

19 - 64
minimate basic
• Do not try to perform maintenance work on the device, except where specified in this manual.
Opening or removing the outer casing may expose you to dangerous live parts or may involve
other risks. All maintenance work must be carried out by authorised staff, except where
specified in this manual.
• Do not tamper with or modify the device.
• Do not perform maintenance or other operations in low light and visibility conditions.
• Do not modify the functional and performance components of the device.
• Do not tamper with the safety devices.
• Do not use the device after maintenance without making sure it is safe. Check that all
components are correctly restored before restarting it.
• Do not remove or make illegible the safety, hazard, and mandatory signs on the device.
• Do not use water or liquids to put out a fire.
• The device has slots and openings for ventilation, do not obstruct or cover them, even partially.
• Always leave the necessary space for ventilation in front of cracks and openings, as indicated
in this manual.
• Do not pull the power cord and make sure it is not too taut when connecting the device.
• Keep the cord and device away from hot surfaces
• Do not cover the cord with rugs or other similar items
• Place the cord in a position away from trafficked areas to avoid the risk of tripping
• Do not remove the plug by pulling on the cord. To perform this operation, hold the plug, not
the cord.
• Extensions should not be used.
• Do not tamper with or modify the power cord.
• Use the power cord supplied with the device, do not use third party power cords
• Switch off the device before disconnecting the plug.
• Unplug when the device is not used for a long time and rewind the cord securely to avoid the
risk of tripping.
• Do not use the device near ovens, fireplaces, stoves or other high temperature heat sources
• Do not use the device near naked flames
• When using the product together with gas appliances in operation (such as gas stoves, gas
water heaters, gas hobs, etc.), adequately ventilate the environment to avoid carbon monoxide
poisoning.
• Do not use the device near air fresheners, essential oils, chemical additives and similar
products.

20 - 64
minimate basic
• Carry the device in its packaging as close to the installation site as possible.
• Do not rest weights or tools on the device, or place it on an unstable surface.
• Check that the various components of the device are fully intact.
• Check that the documentation and all components for installation are contained in
the package.
• Equip yourself with suitable devices for lifting and unpacking of the device.
• The keys to open the front panel must be kept by the user and, if necessary, given
only to authorised users.
6.2 GETTING STARTED
ATTENTION!
Any use other than that specified herein shall be deemed to be
incorrect.
• Disconnect the device from the power supply and contact JONIX S.p.A. or a dealer for
service when any of the following cases occur:
- the internal parts of the device have come into contact with water or other liquids of any
kind;
- a malfunction persists despite all the installation and/or maintenance procedures having
been performed properly;
- the power supply cable is damaged or worn.
Fig. 3
Do not pull the power
cord.
Do not place it near heat
sources.
Do not use naked flames.