Jt Care Steam Wonder 1000 User manual

1
OPERATING INSTRUCTIONS
Jt Care
Steam Wonder 1000
Hot air device
Of the newest generation

2
Table of Contents
Page
Standard Equipment – System Gold 4
Start-up 6
Starting with Accessories 9
Sample Applications 12
Troubleshooting 23
Starting with the Iron 24
Accessories 26
General Use Instructions 29
General Safety Instructions 30
Care 31
Warranty 32
Notes 34

3
Welcome
Dear Customer,
Thank you for purchasing your Jt Care® hot air device and congratulations
on your decision.
You have selected one of the most modern and high-performance devices. This device is
equipped with the most modern technology, which considerably lightens your workload.
Your Jt Care® Hot air device only left production after a careful inspection. Should
however a malfunction occur or should you have questions about operation, please
contact your dealer or call our
Free Service Hotline: [phone]
We wish you all the best in using your device.
Please read through completely before starting!
CHARACTERISTICS
Of the Steam Wonder 1000 at a glance
■2600 Watt boiler output
■3400 Watt total output
■9 bar pressure
■11 bar maximum pressure (safety valve)
■185° boiler temperature
■3 litre boiler volume (total)
■High-grade stainless steel boiler
■Unbreakable ABS plastic housing
■155 cm stainless steel heating hose

4
Standard Equipment – System Gold
Upholstery cover
for floor brush
Upholstery
cover for triangle
Triangle brush Floor brush
Thermo-towels
5 pieces included
cover for triangle
5 pieces included
Thermo-hose

5
Standard Equipment – System Gold
Spray jet Window cleanerSpray jet short grey
Extension 25 cm Extension 2 x 50 cm
Scraper, special-brush attachments, mini-brush attachment, steel polisher
Funnel Drain opener
Funnel

6
1
Starting Up
Open the screw plug on your device.
Pour only cold, pure tap water into your device
and then close it.
ATTENTION! Do not add any cleaning agents
or perfumes!
Lift up and open the lid and push the power plug
for the working hose in completely.
Connecting the hose:
Push the plug for the connection hose completely into
the socket.The hose is correctly inserted if the locking
pin audibly clicks into place.
Disconnecting the hose:
Press the red button and pull the plug out of the device.
Tip: It is easier to press the red button if you first push
the plug into the device a little and the locking pin will
better release the plug.
4
3
2
1
2
3
4

7
5
Starting Up
6
7
5
6
7
Insert the power plug into the electrical socket
and switch the main switch on. Make sure that
the light on the main switch comes on.
Should the acoustic and optical signal (orange light)
go off during operation, add a little water as described
above.
While heating up and during operation, the device
pumps water into the boiler at irregular intervals.
This causes a humming noise.
After around 5 minutes the device is heated up
and the green “ready“ light will come on.

8
8
Starting Up
You adjust the quantity of steam using the wheel
on the handle.
Level 1 generates the lowest quantity of steam.
Level 2 Middle steam level
Level 3 generates the most steam.
Prior to starting work we recommend that you vent
the device for 10 to 15 seconds at the highest steam
level (onto a thermal towel).
The steam is released by pressing on a button under
the handle.
8
9
9

9
Starting Up Accessories
Tubes, hose and accessories can be quite easily
combined with a push lock.
Joint lock
Pushing back the grey slider locks the joint;
pressing it forward releases the joint to move.
When disassembling the accessories, first press
the slider lock forward, and then pull the parts
away from each other.
You can mount the small brush on the jet
(just turn slightly).

10
!Attention: use the protective pad on
sensitive surfaces.
Starting Up Accessories
Inserting a thermo-towel:
Lay a thermo-towel under the floor brush.
Clamp the thermo-towel in place by pressing
on the front two clamps.
You can work like this on smooth floors.
With rougher surfaces (carpeted floors, etc.)
fix the thermo-towel using all four clamps.
+