Jungheinrich WMT Series User manual

1 v1.9 31.08.2021
Jungheinrich WMT
WMT110 / WMT115
Manual
51885736

2 v1.9 31.08.2021
Table of contents
1. Change History ...................................................................4
2. Comments...........................................................................5
2.1 General Comments .......................................................................................................5
2.2 Manufacturer .................................................................................................................5
2.3 Data, Images, Changes.................................................................................................5
2.4 Trademark .....................................................................................................................5
2.5 Copyright .......................................................................................................................5
3. General Description of the truck terminal.........................6
3.1 Use description..............................................................................................................6
3.2 Electrical power data.....................................................................................................6
3.3 Type plate......................................................................................................................7
3.4 Opening the Service Chamber Cover ..........................................................................8
3.5 Overview of interfaces...................................................................................................9
3.6 Antennas WLAN and Bluetooth...................................................................................10
4. Handling ............................................................................11
4.1 Users ...........................................................................................................................11
4.2 Front Buttons (default).................................................................................................11
5. Configuration ....................................................................13
5.1 Jungheinrich WMT Setup Wizard................................................................................13
5.2 WMT Configuration Center..........................................................................................14
System Information......................................................................................................15
USB Lock.....................................................................................................................15
Front Buttons...............................................................................................................16
On-Screen Keyboard...................................................................................................17
Serial Port Wedge .......................................................................................................18
File-Based Write Filter (FBWF) / Unified Write Filter (UWF).......................................19
Volume and Brightness ...............................................................................................21
Ignition Contact............................................................................................................22
Power Button...............................................................................................................24
5.3 Configuration deviations from Windows Standard......................................................25
5.4 Windows Updates (valid for Windows 10)...................................................................25
5.5 Preinstalled 3rd-Party-Software ..................................................................................25
Elo Touchscreen (resistive displays)...........................................................................25
eGalax Touchscreen (capacitive displays)..................................................................26
6. BIOS...................................................................................27
6.1 Navigation in BIOS......................................................................................................27
Enable / Disable interfaces..........................................................................................28

3 v1.9 31.08.2021
7. Reinstall / Backup & Clone / Restore...............................29
7.1 WMT USB Creator.......................................................................................................30
Requirements:.............................................................................................................30
Creating an Install USB stick:......................................................................................30
Boot from Install USB stick..........................................................................................31
7.2 Create a Device Image Backup...................................................................................33
7.3 Reinstall / Restore System from Backup.....................................................................35
7.4 Creation of a Clone Master Image ..............................................................................36
8. Operating Systems...........................................................40
8.1 Windows 10 IoT Enterprise .........................................................................................40
8.2 Windows Embedded Standard 7.................................................................................41

4 v1.9 31.08.2021
1. Change History
Date
Description
Version
15.12.2016
First Version
0.9
20.03.2017
Release 1.0
1.0
27.03.2017
Change Nomenclature / Screenshots
1.1
07.11.2017
Roundup according to German version 1.3
1.3
10.09.2018
Adaptations for SparkLAN Refresh
1.4
02.06.2019
Update for Windows 10 2019 LTSC
1.5
07.11.2019
Formal adaptions
1.6
18.06.2020
Windows Defender added
1.7
28.09.2020
Formal adaptions
1.8
31.08.2021
General Update
1.9

5 v1.9 31.08.2021
2. Comments
2.1 General Comments
This manual is about administration and usage of the Jungheinrich WMT series 110/115. You can find
further information for mounting, cabling and safety-relevant aspects in the separate available quick
installation guide.
The original version of this manual is in German. Every non-german version of this manual is a trans-
lation.
2.2 Manufacturer
Manufacturer of this product is the Jungheinrich AG, in the following called Jungheinrich.
2.3 Data, Images, Changes
All data, images and changes have been created to the best of one’s knowledge and belief. There is
no assurance for any specification. There is no guarantee for integrity and topicality. Subject to change
without prior notice.
2.4 Trademark
All mentioned (soft-/hardware, brands) descriptions are protected by the general trademark right. Other
used foreign brand names are acknowledged. Jungheinrich reserves the right to assert all rights in the
event of a breach of the trademark rights.
2.5 Copyright
This manual is protected by copyright. All entitled users can use this document as part of the purpose
regarding the contract. Every change in usage or recycling of the supplied contents, especially multipli-
cation, changes or publication needs to be approved by Jungheinrich.
Jungheinrich reserves the right to assert rights concerning events of a breach of the copyright.
The copyright of this manual belongs to JUNGHEINRICH AG.
Jungheinrich Aktiengesellschaft
Friedrich-Ebert-Damm 129 - 22047 Hamburg - Deutschland
Telefon: [phone] - www.jungheinrich.com

6 v1.9 31.08.2021
3. General Description of the truck terminal
3.1 Use description
The Jungheinrich truck terminals WMT were specifically developed for use on forklift trucks in logistics
and industrial environments.
The terminal must be operated and stored under the following conditions:
Temperature during operation -30°C to +50°C
Temperature during storage -40°C to +80°C
Air humidity in operation and storage 10% to 95% without condensate.
The terminal is protected against dust and jets of water in accordance with protection rating IP65.
Use in areas where there is a risk of explosion is prohibited.
3.2 Electrical power data
Power supply
Version 12 V
6,5 - 16 V DC
Version 24 - 48 V
16,8 - 72 V DC
Power consumption
typical (maximum)
25 W (58 W)

7 v1.9 31.08.2021
3.3 Type plate
No.
Description
1
Feature number
2
Production date (year and calendar week)
3
Serial number (also as barcode above)
4
WLAN MAC address (also as barcode above)
5
Manufacturer
6
Input voltage and maximum power consumption
7
Material number

8 v1.9 31.08.2021
3.4 Opening the Service Chamber Cover
Note
The relevant safety measures must be observed at all times when handling electrostatically haz-
ardous components. (DIN EN61340-5-1 / DIN EN 61340-5-2).
Remove the screws from the service chamber cover (Fig. II, item 4) using a Torx Tx10 screwdriver.
Remove the service chamber cover from the terminal.

9 v1.9 31.08.2021
3.5 Overview of interfaces
No.
Description
1
Grounding (PE) - 2x1,5mm² flat plug contacts
2
Power supply (0V DC - ignition contact - +12 V or +24/48 V DC)
3
Switch for auto start function (OFF:ON)
4
COM2 (RS232)
5
Switch for 5V at Pin9 COM1 (OFF:ON)
6
COM1 (RS232) with optional 5V power supply on pin 9
7
R-SMA connector for external 2.4/5 GHz WLAN antenna (optional)
8
2 x Ethernet 10/100/1000 Mbit RJ45
9
3 x type A USB 2.0
10
Use grommets to ensure IP65 protection. The grommets have a slot on the side for insertingthe cables.
For strain relief, an additional cable tie can be attached over thecorresponding opening on the outside.

10 v1.9 31.08.2021
3.6 Antennas WLAN and Bluetooth
The two antennas for 2.4/5 GHz WLAN and Bluetooth are protected behind the two plastic covers on
the back of the vehicle terminal. When mounting, make sure that the antennas are not covered.
If the option external antenna has been selected, the internal antenna at the rear right (2) is deac-
tivated and offered externally in the service slot via an R-SMA connector.

11 v1.9 31.08.2021
4. Handling
When the device is switched on for the first time, the operating system automatically starts with the
administrator user and begins with the WMT Setup Wizard (see 5.1 Jungheinrich WMT Setup Wizard).
The WMT will continue to start in setup mode until the wizard has been completed once.
4.1 Users
There are two users preset on the Windows operating system:
Login name: User
User Group: Users
Password: user
Login name: Admin
User Group: Administrators
Password: jhwmt
4.2 Front Buttons (default)
By default, the front buttons of the WMT are assigned to the following presets:
On / Off button.
Operating System will shut down or start.
Power supply will not be disconnected
Note
Change Autologon User:
To change the „autologon user” i.e. after an Active-Directory domain integration, the changes need
to be configured by the following registry options:
Registry-Path
[HKLM\Software\Microsoft\Windows NT\CurrentVersion\winlogon]
Name
Type
Value
Default
Description
AutoAdminLogon
REG_SZ
0 (off) / 1 (on)
1
Autologon de-/activate
DefaultUserName
REG_SZ
<string>
user
Username for Autologon
DefaultPassword
REG_SZ
<string>
user
Userpassword for Autlogon
DefaultDomainName
REG_SZ
<string>
<<leer>>
Domain name

12 v1.9 31.08.2021
Toggle key for the second keyboard layer.
Press and hold, then use the function keys.
Layer 1:
Cancel (ESC)
Layer 2:
Decrease display brightness
Layer 1:
Navigation upwards
Layer 2:
Increase display brightness
Layer 1:
Navigation downwards
Layer 2:
Decrease volume
Layer 1:
Accept (Enter)
Layer 2:
Increase volume
All buttons are individually configurable, except „FN”and the ON / OFF button.
Note
The front button configuration in the operating system differs from the one in BIOS setup. Please
refer to chapter 6.

13 v1.9 31.08.2021
5. Configuration
The following chapter explains the necessary steps for setting up the WMT as well as
other individual software configurations.
5.1 Jungheinrich WMT Setup Wizard
The Jungheinrich WMT Setup-Wizard can be used to set up the WMT and starts automatically at the
first boot. The „WMT Setup Wizard” can set up the following configurations.
- Language and region
- Date, time and time zone
- Computer name
- Network configuration (TCP/IPv4)
- WLAN profiles
The Setup Wizard will always be restarted until it has been completed once.
The WMT Setup Wizard can be started and reset manually using the scripts in the following path:
“C:\Program Files\Jungheinrich\Setup Assistant\setupass.exe”
Note
A system reboot is necessary to complete the device configuration.
Note
The WMT Setup Wizard supports preconfiguring the following WLAN profiles: WEP or WPA /
WPA2 encryption with a Pre-Shared-Key (PSK) authentication. WLAN-Profiles using EAP-authen-
tication must be configured manually by using the Windows network configuration centre.

14 v1.9 31.08.2021
5.2 WMT Configuration Center
The “WMT Configuration Center”is necessary for device specific configurations. Please look for the
desktop icon to start the application. Administrator rights are needed. Further explanation is given in
the following chapter.
The “WMT Info Center”is able to display system information. Please look for the desktop icon to start
the application. No device configuration can be changed.

15 v1.9 31.08.2021
System Information
Displays system specific information:
Computer name
Device type
Serial number
Feature number
BIOS version
Firmware version
Image version
Network information
Hardware equipment
Screen “WMT Configuration Center”and ”WMT Info-Center“are equal.
USB Lock
Tool to disable USB ports.
Note
Only data traffic is blocked. Charging of USB devices is still possible. For a complete lock of the
front USB ports please go to the BIOS menu.

16 v1.9 31.08.2021
To disable a USB port activate the checkbox of the appropriate USB port and save your changes by
clicking on the floppy disk symbol in the upper right hand corner.
Front Buttons
Allows user specific configurations of the front buttons underneath the display. (default config look at
3.2)

17 v1.9 31.08.2021
Changing Button Assignment:
1. Select required front button and click on change.
2. Choose an action.
3. Follow the instructions of the wizard then click on the disk symbol.
The changes will now affect the front button.
The front button configuration is saved under the following registry path:
„[HKEY_LOCAL_MACHINE\SOFTWARE\Jungheinrich\FkCommProxy]”
On-Screen Keyboard
Beside Windows On-Screen-Keyboard (osk.exe) there is another preinstalled keyboard available for
the WMT. This keyboard can be configured further and its icon can be found on the taskbar.

18 v1.9 31.08.2021
Standard layout On-Screen-Keyboard:
The „Configuration Center”enables the following setups
Input language / keyboard layout (alphanumeric / numeric)
Display (colour / transparency)
Automatic fade out after inactivity timeout (in seconds)
Enable key combination
Lock control keys
Serial Port Wedge
By using the „Serial Port Wedge” tool, it is possible to interpret data traffic from a COM port as keyboard
input. Optionally, a Pre- resp. Postcode can be configured. Application example: Barcode scanner with
serial connector.

19 v1.9 31.08.2021
How to configure Serial Port Wedge:
1. Select the appropriate COM port
2. Enable the checkbox „Enable port for Serial Wedge”
3. Configure the transmission settings according to the requirements of your
serial device
4. Optional: Configure a Precode (inserted before entry)
5. Optional: Configure a Postcode (inserted after entry)
6. Save config with disk symbol
Note
Only one process can use a COM port at a time.
File-Based Write Filter (FBWF) / Unified Write Filter (UWF)
FBWF (Windows 7 Embedded) / UWF (Windows 10 IoT) is a Microsoft driver that saves all I/O opera-
tions and redirects them to a special storage cache. By rebooting the operating system on the WMT,
all savings and changes will be deleted. For permanent savings, it is needed to disable the FBWF/UWF.
Switch dropdown to „disable” then click on save and restart the WMT.
Exceptions causing loss of savings / changes are possible by choosing a folder, which will not get
affected by the FBWF. Write protection is provided only for the C: partition, the D: partition is always
excluded from write protection.

20 v1.9 31.08.2021
It is recommended to enable the FBWF/UWF to avoid unintended changes to the system.
Note
All changes according to FBWF/UWF will affect after restarting the WMT.
The current write protection state can be determined either via the configuration menu or via the desktop
information.
DisplayWrite protection disabled Display write protection enabled