Juniper CTP2000 Series User manual

CTP2000 Series
Circuit to Packet Platform
Quick Start Guide
February 2017
Part Number: 530-033822
Revision 01
This document describes how to install the Juniper Networks
®
CTP2000 Series Circuit
to Packet Platform.
Contents CTP2000QuickStartDescription.......................................3
Step1:PreparetheSite...............................................3
BeforeYouUnpackthePlatform....................................3
UnpackthePlatform..............................................3
Inspect the Components and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IfYouDetectorSuspectDamage...................................4
Step2:InstallthePlatform............................................4
BeforeYouBeginInstallation.......................................5
Option: Install the Platform in Freestanding Mode . . . . . . . . . . . . . . . . . . . . . . 5
Option: Install the Platform in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 3: Install Modules and Other Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ModuleInstallationOverview.......................................6
ProtectModulesandSlots.........................................6
Required Tools and Safety Items for Installation . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety Guidelines for Installing Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install a CTP Interface Module, Processor Module, or Clock Module . . . . . . . . 8
InstallaCompactFlashCard.......................................9
InstallaPMCModule............................................10
Install SFPs ....................................................12
Step4:ConnectCables..............................................13
CablingOverview................................................13
Required Tools and Wires for Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ConnectManagementPorts.......................................14
ConnectanInterfaceModule......................................15
CablethePlatformforPower......................................15
1Copyright © 2019, Juniper Networks, Inc.

Step 5: Set Up Access to the CTP Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ConsoleAccess.................................................16
Direct Access ...................................................17
HyperTerminalAccess............................................17
SSHAccess....................................................18
Step6:PowerOn...................................................18
Safety Warnings ....................................................21
Compliance Statements.............................................22
Federal Communications Commission (FCC) Statement . . . . . . . . . . . . . . . . 22
FCC Requirements for Consumer Products . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Food and Drug Administration, Center for Devices and Radiological
Health.....................................................23
Canadian Department of Communications Radio Interference
Regulations ................................................23
IndustryCanadaNoticeCS-03.....................................23
DOC Explanatory Notes: Equipment Attachment Limitations . . . . . . . . . . . . 23
ECDeclarationofConformity......................................24
CTP Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RequestingTechnicalSupport........................................26
Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
OpeningaCasewithJTAC........................................26
Revision History ....................................................27
Copyright © 2019, Juniper Networks, Inc.2
CTP2000 Series Platform Quick Start

CTP2000 Quick Start Description
This Quick Start contains information you need to install and access the CTP2000 series
platform. For complete installation instructions, see the CTP2000 Series Platform
Hardware Documentation at https://www.juniper.net/documentation/.
WARNING: This Quick Start contains a summary of safety warnings in “Safety
Warnings” on page 21. For a complete list of warnings for this router, including
translations, see the CTP2000 Series Platform Hardware Documentation at
https://www.juniper.net/documentation/.
Juniper Networks Circuit to Packet (CTP) products provide advanced technology and
features required to reliably transport legacy time-division multiplexing (TDM) and other
circuit-based applications across next-generation IP networks. CTP platforms create an
IP packet flow from a serial data or analog voice connection at one end and provide the
necessary processing to re-create the serial bit stream or analog signal from the received
packet flow at the other end.
CTP platforms provide compact and lightweight chassis, high port density, and multiple
Ethernet interfaces. Each CTP platform runs the CTP operating system (CTPOS) and
can be managed by CTPView, a secure Web-based management tool for provisioning,
managing, running diagnostics, monitoring, and reporting on all CTP devices and circuits
in the network.
Step 1: Prepare the Site
•Before You Unpack the Platform on page 3
•Unpack the Platform on page 3
•Inspect the Components and Accessories on page 4
•If You Detect or Suspect Damage on page 4
Before You Unpack the Platform
Before you begin unpacking the platform, be sure you have the following tools:
•No. 2 Phillips screwdriver
•Utility knife
•Mechanical lift, or at least two people to assist in lifting
Unpack the Platform
Depending on the platform, it may be delivered boxed, bolted, and strapped to a skid.
For your convenience, we recommend that you unpack the device in the location where
you want to install it.
3Copyright © 2019, Juniper Networks, Inc.
CTP2000 Quick Start Description

WARNING: Three people are required to install the device in a rack: two to
lift the device into position and one to screw it to the rack.
To unpack the device:
1. Cut the two straps that secure the carton to the skid, open the carton from the top,
and remove the box of accessories that sits on top of the device.
2. Unlock the four plastic clips that hold the box to the skid by squeezing them in their
center and pulling out, and then lift the carton off the device.
3. Remove the three screws that attach each of the two L-brackets to the device.
4. To avoid scratching the device when removing it from the skid, detach one of the
L-brackets from the skid by removing the three screws.
Inspect the Components and Accessories
After you remove the equipment from the shipping containers:
•Confirm the contents of each container.
•Inspect all external surfaces and external connectors for visible signs of damage.
•Inspect all accessories shipped with each unit.
•Document any damage noted during your inspection.
•Confirm that the device has the correct number and type of modules for your ordered
configuration.
If You Detect or Suspect Damage
If you detect or suspect damage to any equipment:
•Contact the shipper responsible for delivery, and formally report the damage.
•Contact your Juniper Networks sales representative or reseller.
Step 2: Install the Platform
•Before You Begin Installation on page 5
•Option: Install the Platform in Freestanding Mode on page 5
•Option: Install the Platform in a Rack on page 5
Copyright © 2019, Juniper Networks, Inc.4
CTP2000 Series Platform Quick Start

Before You Begin Installation
Before installing the device:
•Have a plan for installing the device that takes into consideration future expansion.
•Have the tools and accessories needed to complete the installation.
•Be sure that the space requirement of 3 feet (90 cm) behind the device or rack is met.
Do not block air vents on the front or back of the router.
•Prepare the equipment racks by measuring and marking space for each device and
plenum you plan to install.
•See the “Safety Warnings” on page 21.
Option: Install the Platform in Freestanding Mode
When installing the device on a table top or in any other freestanding mode, be sure to
leave enough space around the device for adequate ventilation. Position the chassis with
easy access to the connections that it needs for power, local communications, and remote
communications.
WARNING: Two people are required to lift the device.
CAUTION: To prevent electrostatic damage to the device and its components,
make sure persons handling the device wear an antistatic device.
Option: Install the Platform in a Rack
To install the device in a rack, you need:
•Phillips screwdriver
•Four 10-32 x 3/8 Phillips screws for each device to be installed
Before installing the devices in a rack, consider the following guidelines:
•You can install up to four CTP2056 chassis in a single 7-ft. (2.1-m) rack. Installing
multiple devices in a single rack enables you to maximize your available space.
•Install heavier devices, such as a CTP2056 chassis, on the bottom of the rack. Mount
lighter devices higher in the rack.
Following your installation plan, use a tape measure and marking pen to measure and
mark space on each equipment rack for each device component. For horizontal spacing,
follow Network Equipment Building System (NEBS) requirements.
5Copyright © 2019, Juniper Networks, Inc.
Step 2: Install the Platform

To install the device in the rack:
1. With one person standing on the left side of the device and another standing on the
right side, lift the device into the rack.
2. Position the device in its designated location in the equipment rack. Make sure the
holes of the mounting brackets align evenly with the holes of the equipment rack on
both sides.
3. Starting at the bottom of the device, have the third person secure the device in the
equipment rack by using the 10-32 x 3/8 Phillips screws.
Step 3: Install Modules and Other Components
•Module Installation Overview on page 6
•Protect Modules and Slots on page 6
•Required Tools and Safety Items for Installation on page 7
•Safety Guidelines for Installing Modules on page 7
•Install a CTP Interface Module, Processor Module, or Clock Module on page 8
•Install a CompactFlash Card on page 9
•Install a PMC Module on page 10
•Install SFPs on page 12
Module Installation Overview
In CTP2000 series platforms, interface modules can be installed in the front and rear of
the device. Rear transition modules (RTMs) are located in the rear of the device.
Interface modules are not hot-swappable.
In CTP2000 series platforms, slot numbering starts at the top of the chassis with slot 0.
Protect Modules and Slots
The CTP2056 has an ESD (electrostatic discharge) grounding jack located in the rear
lower-left corner of the chassis near the power switch. To prevent damage from
electrostatic discharge, wear an antistatic wrist strap and connect it to one of the jacks
when handling components. There are no ESD jacks on the other CTP platforms, so you
must use another grounding device.
To protect the modules, components, and slots when installing components, observe
the following guidelines:
CAUTION: When handling components, use an antistatic wrist strap
connected to an appropriate grounding device. This action helps to protect
the module from damage by electrostatic discharge.
Copyright © 2019, Juniper Networks, Inc.6
CTP2000 Series Platform Quick Start

CAUTION: Always handle a module by its edges. Do not touch the
components, pins, leads, or solder connections.
CAUTION: If you meet strong resistance when attempting to seat a module
using the ejectors, remove it from the chassis and confirm that the slot is
designed to hold the module. Also, be sure that you have aligned the left and
right edges in the correct matching module guides.
CAUTION: Be sure to cover every empty slot with a blank filler panel to protect
the device from dust or other foreign substances and to ensure proper device
cooling.
CAUTION: Do not discard the antistatic bag. When a module is not in use,
store it in an antistatic bag.
Required Tools and Safety Items for Installation
You need the following tools to install a CTP module:
•Phillips screwdriver
•Flathead screwdriver
•ESD wrist strap or other grounding device
Safety Guidelines for Installing Modules
Before and during the installation process, observe the following warnings:
WARNING: Do not work on the device or connect or disconnect cables during
lightning activity.
WARNING: Be sure circuit breakers for the power source are in the OFF
position before attaching power cables.
WARNING: Remove jewelry (including rings, necklaces, and watches) before
working on equipment that is connected to power lines. Metal objects heat
up when connected to power and ground and can cause serious burns or
become welded to the terminals.
7Copyright © 2019, Juniper Networks, Inc.
Step 3: Install Modules and Other Components

WARNING: Do not insert any metal object, such as a screwdriver, into an
open slot or the midplane. Doing so can cause electric shock and serious
burns.
WARNING: Never attempt to repair parts of modules yourself. Only trained
customer service personnel are authorized to service parts. Call Juniper
Networks Customer Service to make arrangements to return defective
modules for repair.
Install a CTP Interface Module, Processor Module, or Clock Module
To install a module:
1. Ground yourself by using an antistatic wrist strap or other device, and connect it to
one of the ESD grounding jacks.
2. Choose the slot where you want to insert the module.
3. With a Phillips screwdriver, loosen the screws that secure the blank filler panel covering
the empty chassis slot, if present, and remove the filler panel.
4. Remove the module from its antistatic bag, being careful not to touch module
components, pins, leads, or solder connections.
5. Verify that the ejectors are in the open position (facing outward).
6. Guide the module into the chassis by placing it between the guides of the selected
slot and pushing the module until it stops.
The module stops sliding when the ejectors make contact with the chassis.
CAUTION: If you meet strong resistance when attempting to seat the
module using the ejectors, remove it from the chassis, and confirm that
the slot is designed to hold the component. Also, be sure that you have
aligned the left and right edges in the correct matching tracks.
7. Insert the module into the midplane by simultaneously pressing both ejectors inward
and exerting forward pressure on the module. The small red release buttons should
click into place.
8. Tighten the module's captive screws using a Phillips screwdriver.
Copyright © 2019, Juniper Networks, Inc.8
CTP2000 Series Platform Quick Start

NOTE: Tighten the captive screws completely before installing an adjacent
module so that proper electromagnetic interference (EMI) gasket
compression occurs. Failure to do this can make it difficult to install
adjacent modules.
Install a CompactFlash Card
On the CTP2000 series devices with the new PP833 processor, the CompactFlash card
is installed on the processor itself (which may be located under an installed PMC card),
which prevents insertion or removal of the CompactFlash card until the PMC card is
removed. On the CTP2000 series devices with the PP310 and PP332 processors, the
CompactFlash card is installed on the processor rear transition module (RTM). Some
CTP devices may ship with a CompactFlash card already installed.
To remove or install the CompactFlash card for the CTP2000 series devices with the
new PP833 processor (see Figure 1 on page 9):
1. Power off the unit.
2. If installed, remove the PP833 PMC card by unscrewing the retaining screws and
pushing the extractors outward with the latching buttons depressed.
3. You can then remove or install the CompactFlash card in the flash socket.
4. If being used, reinstall the PP833 PMC card into the chassis, and secure the retaining
screws.
Figure 1: Installing CompactFlash on the PP833 processor
9Copyright © 2019, Juniper Networks, Inc.
Step 3: Install Modules and Other Components

To remove and reinstall the CompactFlash card for the CTP2000 series devices with the
PP310 and PP332 processors:
1. Power off the unit.
2. Remove the RTM by unscrewing the retaining screws and pushing the extractors
outward with the latching buttons depressed.
3. Verify that the CompactFlash card is installed.
4. Remove the CompactFlash card–retaining screw and nut. You can then remove or
install the CompactFlash card in the flash socket.
5. Reinstall the CompactFlash card–retaining screw and nut.
6. Reinstall the processor RTM into the chassis, and secure the retaining screws.
Figure 2: CompactFlash Card on the RTM
IIIIIIIIIIIIIIIIIIIIIIIIIIIII
CompactFlash card
CompactFlash
locking screw
g015386
Install a PMC Module
The PMC module is mounted onto the processor module and can be installed or replaced
in the field. Figure 3 on page 11 displays the location of the PMC module.
Copyright © 2019, Juniper Networks, Inc.10
CTP2000 Series Platform Quick Start