Juniper SSR130 Installation instructions

SSR130 Hardware Guide
Published
2022-01-17

Juniper Networks, Inc.
1133 Innovation Way
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. in
the United States and other countries. All other trademarks, service marks, registered marks, or registered service marks
are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right
to change, modify, transfer, or otherwise revise this publication without notice.
SSR130 Hardware Guide
Copyright © 2022 Juniper Networks, Inc. All rights reserved.
The information in this document is current as of the date on the title page.
YEAR 2000 NOTICE
Juniper Networks hardware and software products are Year 2000 compliant. Junos OS has no known time-related
limitations through the year 2038. However, the NTP application is known to have some difficulty in the year 2036.
END USER LICENSE AGREEMENT
The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with)
Juniper Networks software. Use of such software is subject to the terms and conditions of the End User License Agreement
(“EULA”) posted at https://support.juniper.net/support/eula/. By downloading, installing or using such software, you
agree to the terms and conditions of that EULA.
ii

Table of Contents
Overview
1
SSR130 Appliance Overview | 8
Overview | 8
Benefits of SSR130 | 8
SSR130 Models | 9
SSR130 Chassis | 10
Front Panel of an SSR130 | 10
Rear Panel of an SSR130 | 12
Chassis Status LEDs | 12
Network Port LEDs | 13
SSR130 Power System | 14
Cooling System | 14
LTE Support on SSR130 | 15
Overview | 15
Antennas | 16
Firmware Upgrade Support | 17
Site Planning, Preparation, and Specifications
2
Site Preparation Checklist for SSR130 | 19
SSR130 Site Guidelines and Requirements | 20
General Site Installation Guidelines | 21
Site Electrical Wiring Guidelines | 21
Chassis Physical Specifications for SSR130 | 22
Environmental Requirements and Specifications for SSR130 | 22
Clearance Requirements for Hardware Maintenance of SSR130 | 23
Requirements for Mounting an SSR130 Appliance on a Desktop or Other Level Surface | 24
iii

Rack Requirements for SSR130 | 24
Cable Specifications and Pinouts for SSR130 | 25
Console Port Connector Pinouts for SSR130 | 26
Pluggable Transceivers Supported on SSR130 | 26
Initial Installation and Configuration
3
Unpack and Mount an SSR130 | 28
Unpack an SSR130 | 28
Verify Parts Received with the SSR130 | 29
Register Products—Mandatory to Validate SLAs | 30
Mount an SSR130 on a Desk or Other Level Surface | 30
Mount an SSR130 on a Two-Post Rack | 31
Installing Antennas for the SSR130 Appliances that Support LTE | 33
Inserting the SIM Card | 34
Connect the SSR130 to Power | 35
Connect Earth Ground to SSR130 | 35
Connect Power to SSR130 | 37
Power Off the SSR130 | 38
Connect SSR130 to External Devices | 39
Connect SSR130 to a Management Console | 39
Configuring SSR Software on the SSR130 | 40
Configure the SSR130 Appliance from the SSR Conductor | 41
QuickStart From the OTP ISO | 44
Contacting Customer Support and Returning the Chassis or Components
4
Contacting Customer Support and Returning the Chassis or Components | 51
How to Return a Hardware Component to Juniper Networks, Inc. | 51
Locating the Chassis Serial Number | 52
Contact Customer Support to Obtain Return Material Authorization | 52
Guidelines for Packing Hardware Components for Shipment | 53
iv

Safety and Compliance Information
5
Definitions of Safety Warning Levels | 56
General Safety Guidelines and Warnings | 59
Restricted Access Warning | 61
Qualified Personnel Warning | 64
Prevention of Electrostatic Discharge Damage | 64
Fire Safety Requirements | 66
Fire Suppression | 66
Fire Suppression Equipment | 66
Laser and LED Safety Guidelines and Warnings | 67
General Laser Safety Guidelines | 68
Class 1M Laser Product Warning | 69
Class 1M Laser Radiation Warning | 69
Class 1 Laser Product Warning | 70
Class 1 LED Product Warning | 71
Laser Beam Warning | 72
Unterminated Fiber-Optic Cable Warning | 73
Chassis and Component Lifting Guidelines | 75
Radiation from Open Port Apertures Warning | 76
Maintenance and Operational Safety Guidelines and Warnings | 77
Battery Handling Warning | 78
Jewelry Removal Warning | 79
Lightning Activity Warning | 81
Operating Temperature Warning | 82
Product Disposal Warning | 84
Action to Take After an Electrical Accident | 85
General Electrical Safety Guidelines and Warnings | 85
v

AC Power Electrical Safety Guidelines | 86
SSR130 Agency Approvals | 87
FCC Declarations | 88
Lithium Battery Declaration | 88
vi

1
CHAPTER
Overview
SSR130 Appliance Overview | 8
SSR130 Chassis | 10
LTE Support on SSR130 | 15

SSR130 Appliance Overview
IN THIS SECTION
Overview | 8
Benefits of SSR130 | 8
SSR130 Models | 9
Overview
The Juniper Networks SSR130 is a software-driven network appliance that is part of the SSR branch
portfolio. The SSR130 features six 1 GbE RJ-45, two 1 GbE RJ-45/SFP combo ports, 16 GB of memory,
and a 120 GB enterprise-grade solid-state drive (SSD) for storage.
The SSR130 runs the FIPS 140-2 Level 1 compliant Session Smart Router (SSR) software, which provides
secure and resilient WAN connectivity.
The SSR130 appliance is available in models with or without LTE support.
Benefits of SSR130
The SSR130 provides these benefits:
8

•Zero Trust Security (ZTS)—The SSR130 ensures ZTS by authenticating all routes and encrypting all
session traffic. Applications, devices, or users cannot initiate any session that does not comply with the
authentication policies and access rules. The SSR130 supports session Layer 2 through Layer 5 stateful
firewall functions, including DoS/DDoS protection, NAT, encryption, VPN, and traffic filtering.
•Adaptive encryption—The SSR130 automatically detects traffic encrypted using HTTPs or IPSec and
does not reencrypt such traffic. This capability results in improved performance and reduced overhead
due to double encryption.
•Multipath routing and failsafe service delivery—Application and policy-based multipath routing, intelligent
path monitoring, and application delivery capabilities with no loss ensure that application traffic is
optimized across multiple paths and delivered despite failures.
•Wireless WAN support—In addition to Ethernet connections, Wireless WAN support through the LTE
module provides more flexibility in deployments.
SSR130 Models
The SSR130 is available in three different models, with or without LTE support.
NOTE: To use the SSR130 appliance, you must purchase the SSR software subscription license
sold separately.
Table 1: SSR130 Models
SSR130-AASSR130-AESSR130
16 GB16 GB16 GBRAM
120 GB SSD120 GB SSD120 GB SSDStorage
DesktopDesktopDesktopForm factor
Six 1-Gigabit Ethernet ports
Two 1-Gigabit Ethernet
RJ-45/SFP combo ports
One USB 3.0 port
One RJ-45 Console port
Six 1-Gigabit Ethernet ports
Two 1-Gigabit Ethernet
RJ-45/SFP combo ports
One USB 3.0 port
One RJ-45 Console port
Six 1-Gigabit Ethernet ports
Two 1-Gigabit Ethernet
RJ-45/SFP combo ports
One USB 3.0 port
One RJ-45 Console port
Ports
9

Table 1: SSR130 Models (continued)
SSR130-AASSR130-AESSR130
Two fansTwo fansTwo fansFans
Yes (integrated LTE modem
for Asia Pacific, Australia, and
New Zealand)
Yes (integrated LTE modem
for North America and
Europe)
NoLTE support
SSR130 Chassis
IN THIS SECTION
Front Panel of an SSR130 | 10
Rear Panel of an SSR130 | 12
Chassis Status LEDs | 12
Network Port LEDs | 13
SSR130 Power System | 14
Cooling System | 14
Front Panel of an SSR130
Figure 1 on page 11 shows the front panel of an SSR130.
10

Figure 1: Front Panel Components of SSR130
CONSOLE
POWER
SSR130
RESET
0
1
2
3
g101632
5
46
7
21 3
7 6
4 5
5—1—1 GbE RJ-45/SFP combo portsChassis LEDs
6—2—USB 3.0 portPower button
7—3—Reset buttonConsole Port
4—1 GbE Ethernet ports
Figure 2 on page 11 shows the front panel components of SSR130-AA and SSR130-AE.
Figure 2: Front Panel Components of SSR130-AA and SSR130-AE
5—1—1 GbE RJ-45/SFP Combo PortsAntenna connectors
6—2—USB 3.0 portPower button
7—3—Reset buttonConsole Port
8—4—Chassis LEDs1 GbE Ethernet Ports
The SSR130 supports two 1 GbE RJ-45/SFP combo ports for WAN connectivity. You can connect either
an SFP (fiber) or RJ-45 (copper) cable on the 1 GbE RJ-45/SFP combo port. The SSR130 automatically
detects the media that is connected on the combo port.
If you connect both copper and fiber cables, then the media that establishes the link first becomes active
and the other media is automatically disabled to save power. If the link goes down, then the disabled media
is powered up and both media tries to establish the link again.
11

Rear Panel of an SSR130
Figure 3 on page 12 shows the rear panel of an SSR130.
Figure 3: SSR130 Rear Panel
3—1—Power inputGround terminal
2—Fans
NOTE: The SSR130 does not support the following:
•PoE power input
•Redundant power adapter
Chassis Status LEDs
The SSR130 has three LEDs on the front panel to indicate the status.
Figure 4: Chassis LEDs
Table 2 on page 13 describes the chassis status LEDs on SSR130, their colors and states, and the status
that they indicate.
12

Table 2: Chassis Status LEDs for SSR130
LED State and ColorStatus
LED 1—On, Blue
LED 2—Off, Unlit
LED 3—On, Blue
OS boot process is complete
LED 1—On, Amber
LED 2—Off, Unlit
LED 3—On, Blue
Device is powered off by the OS
Network Port LEDs
Each network port has two LEDs to indicate the link activity and status of the port.
3—1—Link (RJ-45/SFP combo port)Link (Ethernet port)
4—2—Activity (RJ-45/SFP combo port)Activity (Ethernet port)
Table 3 on page 13 describes the Link and Activity LEDs on the network ports.
Table 3: Network Port LEDs on SSR130
State and DescriptionColorLED
The link is up.OnLink
The link is down.Off
13

Table 3: Network Port LEDs on SSR130 (continued)
State and DescriptionColorLED
The link is up and there is traffic on the port.BlinkingActivity
The link is up but there is no traffic on the port.On
The link is down.Off
SSR130 Power System
The SSR130 uses an external AC to DC power adapter.
Table 4 on page 14 lists the specifications for the power supply adapter.
Table 4: Specifications for the Power Adapter
Maximum Power
Consumption
Power Adapter Output
(DC)Power Adapter Input (AC)Model
41.5 W12V DC, 5 A100-240V AC, 50-60 Hz, 2 ASSR130
41.5 W12V DC, 5 A100-240V AC, 50-60 Hz, 2 ASSR130-AA
41.5 W12V DC, 5 A100-240V AC, 50-60 Hz, 2 ASSR130-AE
NOTE: The SSR130 does not support a redundant power adapter.
Cooling System
The cooling system of the SSR130 consists of two fans. The fan controller monitors the temperature of
the chassis and adjusts the fan speed according to the temperature. The SSR130 appliances have
front-to-back airflow. See Figure 5 on page 15.
14

Figure 5: Front-to-Back Airflow Through the SSR130 Chassis
LTE Support on SSR130
IN THIS SECTION
Overview | 15
Antennas | 16
Firmware Upgrade Support | 17
Overview
The SSR130 portfolio consists of models with or without LTE support. The LTE support is provided through
the in-built LTE module that operates on both 3G and 4G networks. The SSR130 supports only a single
SIM card.Table 5 on page 16 provides a summary of the models that support LTE.
15

Table 5: SSR130 Models That Support LTE
Frequency BandOperating RegionModeModel
For 4G LTE:
•Bands 1 through 8, 12, 13, 20, 25, 26,
29, 30, and 41
For 3G:
•Bands 1, 2, 3, 4, 5, and 8
•North America
•European Union
•4G LTE (Cat-6)
•3G (HSPA+, UMTS)
SSR130-AE
For 4G LTE:
•Bands 1, 3, 5, 7, 8, 18, 19, 21, 28, 38, 39,
40, and 41
For 3G:
•Bands 1, 5, 6, 8, 9, and 19
•Asia Pacific
•Australia
•New Zealand
•4G LTE (Cat-6)
•3G (HSPA+, UMTS)
SSR130-AA
Antennas
The LTE module supports two multi-band swivel-mount dipole antennas, which can be rotated 90°. You
can rotate the antennas and select the angle at which the signal strength is high. Table 6 on page 16 lists
the specifications for the antenna.
Table 6: Antenna Specifications for the LTE Module
ValueSpecification
AP-DIPOLE-NEXT-C-IW-S2-BL (Airgain)Part Number
617 MHz-6.0 GHzOperating frequency range
SMAConnector type
16

Table 6: Antenna Specifications for the LTE Module (continued)
ValueSpecification
•1.1 dBi @ 617 MHz
•0.7 dBi @ 850 MHz
•2.3 dBi @ 1450 MHz
•1.6 dBi @ 1750 MHz
•2.5 dBi @ 1950 MHz
•2.2 dBi @ 2250 MHz
•2.6 dBi @ 2450 MHz
•2.7 dBi @ 3700 MHz
•3.5 dBi @ 5500 MHz
Peak Gain
50 OhmsImpedance
252 mm x 35 mm x 13 mmDimensions (L x W X H)
Firmware Upgrade Support
The LTE module supports over-the-air (OTA) firmware upgrade, which enables automatic and timely
upgrade of modem firmware when new firmware versions are available.
17

2
CHAPTER
Site Planning, Preparation, and
Specifications
Site Preparation Checklist for SSR130 | 19
SSR130 Site Guidelines and Requirements | 20
Cable Specifications and Pinouts for SSR130 | 25

Site Preparation Checklist for SSR130
The checklist in Table 7 on page 19 summarizes the tasks you need to perform when preparing a site for
SSR130 installation.
Table 7: Site Preparation Checklist
DatePerformed byFor More InformationItem or Task
Environment
“Environmental Requirements and
Specifications for SSR130” on
page 22
Verify that environmental factors such as
temperature and humidity do not exceed
appliance tolerances.
Power
Measure distance between external power
sources and installation site.
Locate sites for connection of system
grounding.
Calculate the power consumption and
requirements.
Rack
“Rack Requirements for SSR130”
on page 24
Verify that your rack or cabinet meets the
minimum requirements for the installation
of the appliance.
Plan rack location, including required space
clearances.
Secure the rack or cabinet to the floor and
building structure.
Desk
“Requirements for Mounting an
SSR130 Appliance on a Desktop
or Other Level Surface” on
page 24
Verify that the desk meets the minimum
requirements for the installation of the
appliance.
19

Table 7: Site Preparation Checklist (continued)
DatePerformed byFor More InformationItem or Task
“Clearance Requirements for
Hardware Maintenance of
SSR130” on page 23
Verify that there is appropriate clearance in
your selected location.
Cables
Acquire cables and connectors:
•Determine the number of cables needed
based on your planned configuration.
•Review the maximum distance allowed
for each cable. Choose the length of cable
based on the distance between the
hardware components being connected.
Plan the cable routing and management.
SSR130 Site Guidelines and Requirements
IN THIS SECTION
General Site Installation Guidelines | 21
Site Electrical Wiring Guidelines | 21
Chassis Physical Specifications for SSR130 | 22
Environmental Requirements and Specifications for SSR130 | 22
Clearance Requirements for Hardware Maintenance of SSR130 | 23
Requirements for Mounting an SSR130 Appliance on a Desktop or Other Level Surface | 24
Rack Requirements for SSR130 | 24
20