Jura IMPRESSA C9 User manual

IMPRESSA C9 – Quick Reference Guide
The ‘IMPRESSA Manual’ together with these short instruc-
tions ‘IMPRESSA C9 – Quick Reference Guide’ has been
awarded the seal of approval by the independent German
Technical Inspection Agency, TÜV SÜD, due to its easy-to-
understand style, its thoroughness and coverage of safety
aspects.

2
IMPRESSA C9 – Quick Reference Guide
These short instructions do not replace the ‘IMPRESSA C9 Manual’.
Make sure you read and observe the safety information and warn-
ings first in order to avoid hazards.
Precondition: Your IMPRESSA is switched on at the power switch and
the indicator light is illuminated (standby).
Q T Press the On/Off button to switch the IMPRESSA on.
HEATING is displayed.
PRESS RINSE, the maintenance button clights up.
Place a receptacle under the coffee spout.
c T Press the maintenance button.
RINSING, the machine rinses.
Preparation stops automatically. READY appears on the
display.
Your IMPRESSA no longer has to be descaled if you are using CLARIS
plus filter cartridges.
Perform the ’Insert filter’ operation without interruptions. This
will ensure that your IMPRESSA always produces its best.
Precondition: READY is displayed.
Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until RINSE appears on
the display.
g T Turn the Rotary Switch until FILTER - is displayed.
k T Press the Rotary Switch to enter the programme item.
NO -
g T Turn the Rotary Switch until YES w is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display to confirm the setting.
INSERT, the maintenance button clights up.
Close the cover of the Rotary Switch.
Remove the CLARIS plus filter cartridge from the Welcome
Pack.
Remove the water tank and empty it.
T
E
T
T
T
T
Switching onSwitching on
Using and activating
filter
Using and activating
filter

3
IMPRESSA C9 – Quick Reference Guide
Lift the cartridge holder and insert the filter cartridge into
the water tank, applying slight pressure.
Close the cartridge holder. It will click into place audibly.
Fill the water tank with fresh, cold water and reinsert.
Place a receptacle (at least 500 ml) under the frother.
c T Press the maintenance button.
FILTER RINSING. Water will flow out of the frother.
You can interrupt rinsing of the filter at any time by pressing
any button.
The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml.
HEATING appears on the display, then READY is dis-
played. The filter is now activated.
After 50 litres of water have flowed through, or after two
months, the filter will cease to work. Your IMPRESSA will auto-
matically prompt you to change the filter.
If the CLARIS plus filter cartridge is not activated, you will not
be prompted to change the filter.
To change the CLARIS plus filter cartridge when prompted to do so
by your IMPRESSA, proceed as follows:
Precondition: READY / FILTER is displayed and the mainte-
nance button clights up.
c T Press the maintenance button.
CHANGE
Remove the water tank and empty it.
Open up the cartridge holder and remove the old CLARIS
plus filter cartridge.
T
T
T
T
E
E
E
E
T
T
Filter changeFilter change

4
IMPRESSA C9 – Quick Reference Guide
Insert a new CLARIS plus filter cartridge into the water tank,
pressing it slightly.
Close the cartridge holder. It will click into place audibly.
Fill the water tank with fresh, cold water and reinsert.
Place a receptacle (at least 500 ml) under the frother.
If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING – Water will flow out of the frother.
You can interrupt filter rinsing at any time. To do this, press
any button.
The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml. The
IMPRESSA heats up and is once again ready to use.
After 200 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
Use only original JURA care products.
The cleaning programme only lasts about 20 minutes.
Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
JURA cleaning tablets are available from stockists.
Precondition: READY / CLEAN is displayed and the maintenance
button clights up.
c T Press the maintenance button.
T
T
T
T
E
E
E
T
E
E
E
Clean machineClean machine
CAUTIONCAUTION

5
IMPRESSA C9 – Quick Reference Guide
EMPTY TRAY
Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE, the maintenance button clights up.
Place a receptacle under the coffee spout and the frother.
c T Press the maintenance button.
CLEANING, water flows from both coffee spouts.
The process is interrupted, ADD TABLET.
Open the cover of the filler funnel for pre-ground coffee.
Insert a JURA cleaning tablet into the filler funnel.
Close the cover of the filler funnel.
c T Press the maintenance button.
CLEANING, water flows from both coffee spouts several
times.
The process is interrupted – EMPTY TRAY.
Empty the drip tray and coffee grounds container and put
them back into the machine.
The cleaning operation is now complete. The IMPRESSA is
ready for use again.
T
T
T
T
T
T

6
IMPRESSA C9 – Quick Reference Guide
The IMPRESSA builds up deposits of limescale over time and auto-
matically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
Avoid contact with the skin or eyes.
Rinse the descaling agent off with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dam-
aged and/or traces of detergent could be left behind in the water.
Use only original JURA care products.
If the descaling operation is interrupted, there may be damage to
the machine.
Allow the descaling program to run to the end.
If the descaling agent comes into contact with sensitive surfaces,
damage cannot be ruled out.
Clean up any splashes immediately.
The descaling programme lasts approx. 45 minutes.
JURA descaling tablets are available from stockists.
If you use a CLARIS plus filter cartridge and this is activated,
you will not be prompted to change the filter.
Precondition: READY / DE-SCALE is displayed and the mainte-
nance button clights up.
c T Press the maintenance button.
EMPTY TRAY
Empty the drip tray and coffee grounds container and put
them back into the machine.
AGENT IN TANK
Remove the water tank and empty it.
T
T
T
T
T
E
E
E
T
T
Descale machineDescale machine
CAUTIONCAUTION
CAUTIONCAUTION
CAUTIONCAUTION
CAUTIONCAUTION

7
IMPRESSA C9 – Quick Reference Guide
Completely dissolve the contents of one blister (3 JURA des-
caling tablets) in a container that holds 500 ml of water. This
may take several minutes.
Pour the solution into the empty water tank and insert it in
the machine.
AGENT IN TANK, the maintenance button clights up.
Remove the frother.
Place a receptacle (at least 500 ml) under the Connector Sys-
tem©.
c T Press the maintenance button.
DE-SCALING
This causes water to flow out of the Connector System©sev-
eral times. The maintenance button blinks during the des-
caling operation.
The operation stops automatically, EMPTY TRAY.
Empty the receptacle under the Connector System©.
Empty the drip tray and coffee grounds container and put
them back into the machine.
FILL WATER TANK
Remove the water tank and rinse it thoroughly.
Fill the water tank with fresh, cold mains water and rein-
sert.
PRESS RINSE, the maintenance button clights up.
Replace the frother.
Place a receptacle under the frother.
c T Press the maintenance button.
DE-SCALING, water flows out of the frother.
The operation stops automatically, EMPTY TRAY.
Empty the drip tray and coffee grounds container and put
them back into the machine.
The descaling operation is now complete. Your IMPRESSA
heats up and is once again ready to use.
If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
T
T
T
T
T
T
T
T
T
T
T
E

8
IMPRESSA C9 – Quick Reference Guide
To ensure that the Easy Cappuccino Frother works perfectly, you
should rinse it with water whenever you have prepared some milk.
Your IMPRESSA will prompt you to rinse the Easy Cappuccino Frother
10 minutes after you have prepared milk.
Precondition: CAPPUCCINO RINSE is displayed and the main-
tenance button clights up.
Place a receptacle under the Easy Cappuccino Frother.
c T Press the maintenance button.
CAPPUCCINO RINSING, the frother is rinsed.
Preparation stops automatically. READY appears on the
display.
To ensure that the Easy Cappuccino Frother works perfectly, you
should clean it daily when you have been preparing milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
Use only original JURA care products.
The JURA Auto Cappuccino Cleaner is available from
stockists.
The IMPRESSA will not prompt you to clean the frother.
Precondition: READY is displayed.
Remove the milk pipe from the milk carton/bottle or the
milk container.
Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
C CLEANING
k T Press the Rotary Switch.
CAPPUCCINO CLEANER
Pour 250 ml of fresh water into a container and add one cap-
ful (max. 15 ml) of Auto Cappuccino Cleaner.
T
T
E
E
T
T
T
Rinsing the Easy
Cappuccino Frother
Rinsing the Easy
Cappuccino Frother
Cleaning the Easy
Cappuccino Frother
Cleaning the Easy
Cappuccino Frother
CAUTIONCAUTION

9
IMPRESSA C9 – Quick Reference Guide
Immerse the milk pipe in the receptacle.
Place another receptacle under the frother.
c T Press the maintenance button.
CLEANING, the frother and pipe are cleaned. The opera-
tion stops automatically.
WATER FOR CAPPUCCINO
Rinse the receptacle thoroughly, fill it with approx. 250 ml
of fresh water and immerse the milk pipe in the water.
Empty the other receptacle and place it under the frother
once more.
c T Press the maintenance button.
CLEANING, the frother and pipe are rinsed with fresh
water. The operation stops automatically.
READY appears on the display.
Close the cover of the Rotary Switch.
Carefully remove the frother from the Connector System©
by twisting slightly.
Dismantle the frother completely.
Rinse all the frother parts thoroughly under running water.
Reassemble the frother.
Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
Firmly attach the frother to the Connector System©.
T
T
T
T
T
T
T
T
T
E
T
Disassembling and
rinsing the Easy
Cappuccino Frother
Disassembling and
rinsing the Easy
Cappuccino Frother

10
IMPRESSA C9 – Quick Reference Guide
To ensure that the Professional Cappuccino Frother works perfectly,
you should rinse it with water whenever you have prepared some
milk.
Your IMPRESSA will prompt you to rinse the Professional Cappuc-
cino Frother 10 minutes after you have prepared milk.
Precondition: CAPPUCCINO RINSE is displayed and the main-
tenance button clights up.
Place a receptacle under the Professional Cappuccino
Frother.
c T Press the maintenance button.
CAPPUCCINO RINSING, the frother is rinsed.
Preparation stops automatically. READY appears on the
display.
To ensure that the Professional Cappuccino Frother works perfectly,
you should clean it daily when you have been preparing milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
Use only original JURA care products.
The JURA Auto Cappuccino Cleaner is available from
stockists.
The IMPRESSA will not prompt you to clean the frother.
Precondition: READY is displayed.
Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
C CLEANING
k T Press the Rotary Switch.
CAPPUCCINO CLEANER
Remove the milk pipe from the milk carton/bottle or the
milk container.
Pour 250 ml of fresh water into a container and add one cap-
ful (max. 15 ml) of Auto Cappuccino Cleaner.
T
T
E
E
T
T
T
Rinsing
the Professional
Cappuccino Frother
Rinsing
the Professional
Cappuccino Frother
Cleaning
the Professional
Cappuccino Frother
Cleaning
the Professional
Cappuccino Frother
CAUTIONCAUTION

11
IMPRESSA C9 – Quick Reference Guide
Immerse the milk pipe in the receptacle.
Turn the selection lever of the frother to the milk foam posi-
tion por milk t.
Place another receptacle under the frother.
c T Press the maintenance button.
CLEANING, the frother and pipe are cleaned. The opera-
tion stops automatically.
WATER FOR CAPPUCCINO
Rinse the receptacle thoroughly, fill it with approx. 250 ml
of fresh water and immerse the milk pipe in the water.
Empty the other receptacle and place it under the frother
once more.
c T Press the maintenance button.
CLEANING, the frother and pipe are rinsed with fresh
water.
Preparation stops automatically. READY appears on the
display.
Close the cover of the Rotary Switch.
Carefully remove the frother from the Connector System©
by twisting slightly.
Dismantle the frother completely.
Rinse all the frother parts thoroughly under running water.
Reassemble the frother.
Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
Firmly attach the frother to the Connector System©.
T
T
T
T
T
T
T
T
T
T
E
T
Disassembling and
rinsing the
Professional
Cappuccino Frother
Disassembling and
rinsing the
Professional
Cappuccino Frother

Art. 67620/C9/en/0711