Jura IMPRESSA XS95 ONE TOUCH User manual

IMPRESSA XS95/XS90 One Touch–
Quick Reference Guide
The ‘IMPRESSA Manual’ together with these short instruc-
tions ‘IMPRESSA XS95/XS90 One Touch – Quick Reference
Guide’ has been awarded the seal of approval by the inde-
pendent German Technical Inspection Agency, TÜV SÜD,
due to its easy-to-understand style, its thoroughness and
coverage of safety aspects.

2
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
These short instructions do not replace the ‘IMPRESSA XS95/XS90
One Touch Manual’. Make sure you read and observe the safety
information and warnings first in order to avoid hazards.
When the IMPRESSA is switched on, a prompt for the rinse operation
automatically appears which is initiated by pressing the mainte-
nance button.
Precondition: Your IMPRESSA is switched on at the power switch
and the on/off button Qis illuminated (standby).
Q T Press the on/off button to switch the IMPRESSA on.
WELCOME TO JURA appears briefly on the display.
HEATING UP
PRESS RINSE, the maintenance button clights up.
Place a receptacle under the coffee spout.
c T Press the maintenance button.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
Your IMPRESSA no longer has to be descaled if you are using CLARIS
plus filter cartridges.
Perform the ‘Insert filter’ operation without interruptions. This
will ensure that your IMPRESSA always produces its best.
Precondition: COFFEE READY is displayed.
Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears on the display.
g T Turn the Rotary Switch until FILTER NO is displayed.
k T Press the Rotary Switch to enter the programme item.
FILTER NO
g T Turn the Rotary Switch until FILTER YES is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display to confirm
the setting.
T
E
T
Switching onSwitching on
Using and
activating filter
Using and
activating filter

3
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
INSERT FILTER / PRESS RINSE, the maintenance
button clights up.
Remove a CLARIS plus filter cartridge and the filter cartridge
extension from the Welcome Pack.
Fit the extension on top of the filter cartridge.
Remove the water tank and empty it.
Lift the cartridge holder and insert the filter cartridge into
the water tank, applying slight pressure.
Close the cartridge holder. It will click into place audibly.
Fill the water tank with fresh, cold water and reinsert.
Place a receptacle (at least 500 ml) under the frother.
If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING, water flows out of the frother.
You can interrupt rinsing of the filter at any time by pressing
any button.
The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml.
COFFEE READY appears on the display. The filter is now
activated.
T
T
T
T
T
T
T
E
E
E

4
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
After 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you
to replace the filter.
After two months, the filter will cease to work. Monitor the
elapsed time by adjusting the date plate on the cartridge
holder.
If the CLARIS plus filter cartridge is not activated, you will not
be prompted to change the filter.
To change the CLARIS plus filter cartridge when prompted to do so
by your IMPRESSA, proceed as follows:
Precondition: COFFEE READY / CHANGE FILTER is dis-
played, and the maintenance button clights up.
c T Press the maintenance button.
DURATION 2 MIN. / START YES
If you want to change the filter at a later point in time, turn the
Rotary Switch until START NO is displayed. Exit the mainte-
nance programme by pressing the Rotary Switch. The prompt
‘Change filter’ remains on the display.
c T Press the maintenance button.
CHANGE FILTER / PRESS RINSE
Remove the water tank and empty it.
Lift the cartridge holder.
Take out the old CLARIS plus filter cartridge and the exten-
sion.
Fit the extension on top of a new filter cartridge.
Insert the filter cartridge into the water tank, exerting slight
pressure.
Close the cartridge holder. It will click into place audibly.
Fill the water tank with fresh, cold water and reinsert.
E
E
E
E
T
T
T
T
T
T
T
Changing the filterChanging the filter

5
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
Place a receptacle (at least 500 ml) under the frother.
If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING, water flows out of the frother.
You can interrupt filter rinsing at any time. To do this, press
any button.
The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml. The
IMPRESSA heats up and is once again ready to use.
After 220 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
Use only original JURA care products.
The cleaning programme only lasts about 20 minutes.
Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
JURA cleaning tablets are available from stockists.
Precondition: COFFEE READY / CLEAN MACHINE is dis-
played, and the maintenance button clights up.
c T Press the maintenance button.
DURATION 20 MIN. / START YES
If you want clean the machine at a later point in time, turn the
Rotary Switch until START NO is displayed. Exit the mainte-
nance programme by pressing the Rotary Switch. The prompt
‘Clean machine’ remains on the display.
T
E
E
E
T
E
E
E
E
Cleaning the machineCleaning the machine
CAUTIONCAUTION

6
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
c T Press the maintenance button.
EMPTY TRAY
Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE, the maintenance button clights up.
Place a receptacle under the coffee spout and the frother.
c T Press the maintenance button.
CLEANS, the cleaning operation starts.
The process is interrupted. ADD TABLET / PRESS
RINSE, the maintenance button clights up.
Open the cover of the filler funnel for pre-ground coffee.
Insert a JURA cleaning tablet into the filler funnel.
Close the cover of the filler funnel.
c T Press the maintenance button.
CLEANS, water flows out of the coffee spout and the
frother several times.
You can follow the current status of cleaning on the progress
bar.
The process is interrupted, EMPTY TRAY.
Empty the drip tray and coffee grounds container and put
them back into the machine.
The cleaning operation is now complete. The IMPRESSA is
ready for use again.
T
T
T
T
T
E
T

7
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
The IMPRESSA builds up deposits of limescale over time and auto-
matically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
Avoid contact with the skin or eyes.
Rinse the descaling agent off with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dam-
aged and/or traces of detergent could be left behind in the water.
Use only original JURA ca re products.
If the descaling operation is interrupted, there may be damage to
the machine.
Allow the descaling program to run to the end.
If the descaling agent comes into contact with sensitive surfaces,
damage cannot be ruled out.
Clean up any splashes immediately.
The descaling programme lasts approx. 45 minutes.
JURA descaling tablets are available from stockists.
If you use a CLARIS plus filter cartridge and this is activated,
you will not be prompted to change the filter.
Remove the CLARIS plus filter cartridge, if installed, before de-
scaling the machine.
Precondition: COFFEE READY / DECALCIFY MACHINE is
displayed and the maintenance button clights up.
c T Press the maintenance button.
DURATION 45 MIN. / START YES
If you want to descale the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance programme by pressing the Rotary Switch. The
prompt ‘Decalcify machine’ remains on the display.
T
T
T
T
T
E
E
E
E
E
Descaling the machineDescaling the machine
CAUTIONCAUTION
CAUTIONCAUTION
CAUTIONCAUTION
CAUTIONCAUTION

8
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
c T Press the maintenance button.
EMPTY TRAY
Empty the drip tray and coffee grounds container and put
them back into the machine.
SOLVENT IN TANK
Remove the water tank and empty it.
Completely dissolve the contents of one blister (3 JURA des-
caling tablets) in a container that holds 600 ml of water. This
may take several minutes.
Pour the solution into the empty water tank and insert it in
the machine.
SOLVENT IN TANK / PRESS RINSE, the mainte-
nance button clights up.
Remove the frother from the Connector System©.
Place a receptacle under the hot water spout and another
under the Connector System©.
c T Press the maintenance button.
DECALCS, water flows out of the Connector System©and
the hot water spout. The maintenance button cflashes
during the descaling operation.
You can follow the current status of descaling on the progress
bar.
The process is interrupted, EMPTY TRAY.
Empty the receptacles below the hot water spout and the
Connector System©.
Empty the drip tray and coffee grounds container and put
them back into the machine.
RINSE WATER TANK / FILL WATER TANK
Remove the water tank and rinse it thoroughly.
Fill the water tank with fresh, cold water and reinsert.
PRESS RINSE, the maintenance button clights up.
Refit the frother.
T
T
T
T
T
T
E
T
T
T
T
T

9
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
Place a receptacle under the coffee and hot water spout and
another under the frother.
c T Press the maintenance button.
DECALCS, water flows out of the frother and the hot water
spout.
The process is interrupted, HEATING UP.
MACHINE RINSING, water flows out of the coffee
spout. The operation stops automatically, EMPTY TRAY.
Empty the drip tray and coffee grounds container and put
them back into the machine.
The descaling operation is now complete. Your IMPRESSA
heats up and is once again ready to use.
If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
This chapter applies to the Professional and Easy Cappuccino
Frothers.
Each time milk has been prepared the IMPRESSA displays a prompt
for Cappuccino rinsing.
Precondition: COFFEE READY / RINSE CAPPUCCINO is
displayed and the maintenance button clights up.
Place a receptacle under the frother.
If you are using the Professional Cappuccino Frother, turn
the selection lever to the steam position n.
c T Press the maintenance button.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
appears on the display.
T
T
E
E
T
E
Rinsing the
cappuccino frother
Rinsing the
cappuccino frother

10
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
This chapter applies to the Professional and Easy Cappuccino
Frothers.
To ensure that the respective frother works perfectly, you should
clean it daily when you have been preparing milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
Use only original JURA care products.
The JURA Auto-Cappuccino Cleaner is available from
stockists.
Precondition: COFFEE READY is displayed.
Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
k T Press the Rotary Switch.
CLEANER FOR CAPPU., the maintenance button c
lights up.
Pour 250 ml of fresh water into a container and add one
capful (max. 15 ml) of Auto-Cappuccino Cleaner.
Immerse the milk pipe in the receptacle with the cleaning
solution.
If you are using the Professional Cappuccino Frother, turn
the selection lever to the milk foam por milk tposition.
Place another receptacle under the frother.
c T Press the maintenance button.
CAPPUCCINO CLEANING, the frother and pipe are
cleaned.
WATER FOR CAPPUCCINO, the maintenance button c
lights up.
Rinse the receptacle thoroughly, fill it with approx. 250 ml
of fresh water and immerse the milk pipe in the water.
E
T
E
T
T
T
E
T
T
Cleaning the
cappuccino frother
Cleaning the
cappuccino frother
CAUTIONCAUTION

11
IMPRESSA XS95/XS90 One Touch – Quick Reference Guide
Empty the other receptacle and place it under the frother
once more.
c T Press the maintenance button.
CAPPUCCINO CLEANING, the frother and pipe are
rinsed with fresh water.
COFFEE READY appears on the display. Your IMPRESSA
is once more ready to use.
Carefully remove the frother from the Connector System©
by twisting slightly.
Dismantle the frother completely.
Rinse all the frother parts thoroughly under running water.
Reassemble the frother.
Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
Firmly attach the frother to the Connector System©.
Carefully remove the frother from the Connector System©
by twisting slightly.
Dismantle the frother completely.
Rinse all the frother parts thoroughly under running water.
Reassemble the frother.
Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
Firmly attach the frother to the Connector System©.
T
T
T
T
T
E
T
T
T
T
T
E
T
Disassembling and
rinsing the
Professional
Cappuccino Frother
Disassembling and
rinsing the
Professional
Cappuccino Frother
Disassembling and
rinsing the Easy
Cappuccino Frother
Disassembling and
rinsing the Easy
Cappuccino Frother

Art. 67801/XS95/en/0712