JVC KD-S757R User manual

FSUN3062-311
[E]
INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
GEBRUIKSAANWIJZING
KD-SX858R/KD-S757R
CD RECEIVER
CD-RECEIVER
RECEPTEUR CD
CD-RECEIVER
ENGLISH
DEUTSCH
NEDERLANDS
FRANÇAIS
For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende
handleiding.
COMPACT
DIGITAL AUDIO
40Wx4
SEL
DISP
RPT SSM
MO/RND
KD-S757R
COMPACT
DIGITALAUDIO
TP
RDS PTY
C D
A M
F M
SOUND
789101112
40Wx4
SEL
DISP
RPT SSM
MO/RND
KD-SX858R
COMPACT
DIGITALAUDIO
TP
RDS PTY
CD
CHANGER
CONTROL
C D
CD-CH
FM/AM
SOUND
7 8 9 10 11 12
KD-SX858R
ATT
FUNC
BAND
PROG
PRESET
DISC
DISC
KD-S757R
COVER.KD-SX858R/S757R[E]E,G,F,N 98.10.9, 7:23 PM3

2
DANGER: Invisible laser
radiation whenopen and
interlock failedordefeated.
AVOID DIRECT EXPOSURE
TO BEAM. (e)
ADVARSEL:Usynlig laser-
stråling ved åbning, når
sikkerhedsafbrydere erude
af funktion.Undgåudsæt-
telse for stråling. (d)
VARNING:Osynliglaser-
strålning när denna del
är öppnadochspärren är
urkopplad. Betrakta ej
strålen. (s)
VARO : Avattaessa ja suo-
jalukitus ohitettaessa olet
alttiina näkymättömälle
lasersäteilylle. Älä katso
säteeseen. (f)
Caution:
This product contains a laser component
of higher laser class than Class 1.
IMPORTANT FOR LASER
PRODUCTS
Precautions:
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when
openandinterlockfailedor defeated.Avoid
direct exposure to beam.
3. CAUTION: Do not open the top cover.
Therearenouser-serviceablepartsinside.
Leave all servicing to qualified service
personnel.
4. CAUTION: This CD player uses invisible
laser radiation and is equipped with safety
switches to prevent radiation emission
when unloading CDs. It is dangerous to
defeat the safety switches.
5. CAUTION:Use of controls,adjustmentsor
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
CAUTION on Volume Setting
CDs produce very little noise compared with other sources. If the volume level is adjusted for the
tuner,forexample, the speakers maybedamaged bythesudden increaseintheoutputlevel.Therefore,
lower the volume before playing a disc and adjust it as required during playback.
Note:
For security reasons, a numbered ID card is provided with this unit, and the same ID number is
imprinted on the unit’s chassis. Keep the card in a safe place, as it will help the authorities to
identify your unit if stolen.
Position And Reproduction Of Labels
Bottom panel of the main unit
Name/Rating plate
EN02-05.KD-SX858R/S757R[E]/1 98.10.13, 4:20 PM2

3
ENGLISH
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to
ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
BASIC OPERATIONS .................................................... 5
RADIO BASIC OPERATIONS .........................................6
Listening to the radio ..................................................................... 6
Storing stations in memory ............................................................ 7
FM station automatic preset: SSM...............................................7
Manual preset.............................................................................. 8
Tuning into a preset station ........................................................... 9
Selecting FM reception sound ....................................................... 9
RDS OPERATIONS .....................................................10
What you can do with RDS EON ................................................10
Tracing the same programme automatically (Network-Tracking
Reception) ................................................................................. 10
Using Standby Reception.......................................................... 12
SelectingYour Favorite Programme for PTY Standby Reception .. 13
SearchingYour Favorite Programme..........................................13
Other convenient RDS functions................................................. 16
Automatic selection of the station when using the number
buttons....................................................................................... 16
Changing the display mode while listening to an FM station..... 16
Setting the TA volume level........................................................16
Automatic clock adjustment .......................................................17
CD OPERATIONS....................................................... 18
Playing a CD .................................................................................18
Locating a track or a particular portion on a CD ..................... 19
Selecting CD playback modes......................................................20
Prohibiting CD ejection ...............................................................21
SOUND ADJUSTMENTS .............................................22
Selecting preset sound control modes ......................................... 22
Adjusting the sound...................................................................... 23
Storing your own sound adjustments ......................................... 24
CONTINUEDTO THE NEXT PAGE
EN02-05.KD-SX858R/S757R[E]/1 98.10.9, 5:39 PM3

4
OTHER MAIN FUNCTIONS .........................................25
Setting the clock............................................................................ 25
Changing the general settings......................................................27
Selecting 24-hour or 12-hour clock ............................................28
Selecting the level display ......................................................... 29
Selecting the display mode while using the CD changer
(ONLY FOR KD-SX858R) .........................................................29
Selecting the telephone muting (ONLY FOR KD-SX858R) ....... 29
Detaching the control panel .........................................................30
REMOTE OPERATIONS............................................... 31
(ONLY FOR KD-SX858R)
Installing the batteries..................................................................31
Using the remote controller .........................................................31
CD CHANGER OPERATIONS ......................................32
(ONLY FOR KD-SX858R)
Playing CDs ...................................................................................32
Selecting CD playback modes......................................................34
MAINTENANCE......................................................... 35
Handling Discs ..............................................................................35
Taking care of CDs .................................................................... 35
Moisture condensation .............................................................. 35
TROUBLESHOOTING ................................................. 36
SPECIFICATIONS .......................................................37
BEFORE USE
* For safety....
• Do not raise the volume level too much, as this
will block outside sounds, making driving
dangerous.
• Stop the car before performing any complicated
operations.
*Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
EN02-05.KD-SX858R/S757R[E]/1 98.10.9, 5:39 PM4

5
ENGLISH
Adjust the volume.
4
Adjust the sound as you want (see pages 22 – 24).
To drop the volume in a moment
Press briefly while listening to any source.“ATT”starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the button briefly again.
To turn off the power
Press and hold for more than 1 second.
BASIC OPERATIONS
1
Turn on the power.
2
Select the source.
To operate the tuner, see pages 6 – 17.
To operate the CD player, see pages 18 – 21.
To operate the CD changer, see pages 32 – 34.
(ONLY FOR KD-SX858R)
3
Note on One-Touch Operation:
When you select a source in step 2 below, the power automatically comes on.
You do not have to press this button to turn on the power.
Volume level appears.
Note:
When you use this unit for the
first time, set the built-in
clock correctly, see page 25.
2
SEL
C D
F M
A M
C D
CD-CH
FM/AM
KD-SX858R KD-S757R
EN02-05.KD-SX858R/S757R[E]/1 98.10.9, 5:39 PM5

6
RADIO BASIC OPERATIONS
Listening to the radio
FM/AM
KD-S757R
COMPACT
DIGITAL AUDIO
TP
RDS PTY
C D
CD-CH
SOUND
1
Select the band (FM1, FM2, FM3 or AM).
You can select any one of FM1, FM2, and FM3 to listen to an
FM station.
FM1 FM2 FM3 AM
KD-SX858R
KD-S757R
FM/AM
KD-S757R
AM
A M
F M
FM1 FM2
FM3
2
Start searching a station.
When a station is received, searching stops.
To stop searching before a station is received, press the same button you have pressed
for searching.
To tune in a particular frequency without searching
1Select the band (FM or AM).
For KD-SX858R: Press FM/AM repeatedly.
For KD-S757R: Press FM or AM.
2Press and hold ¢or 4until “M” (for Manual) starts flashing on the display.
Now you can manually change the frequency while “M” is flashing.
3Press ¢or 4repeatedly until the frequency you want is reached.
• If you hold down the button, the frequency keeps changing (in 50 kHz intervals for FM and
9kHz intervals for AM–MW/LW) until you release the button.
To search stations
of lower
frequencies.
To search stations
of higher
frequencies.
KD-SX858R
Selected band appears.
Audio level indicator
(See page 29.)
EN06-12.KD-SX858R/S757R[E]/1 98.10.9, 5:38 PM6

7
ENGLISH
Storing stations in memory
You can use one of the following two methods to store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-station Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band (FM1, FM2 and FM3).
1
Select the FM band number (FM1, FM2 or
FM3) you want to store FM stations into.
2
Press and hold both buttons for more than
2 seconds.
Local FM stations with the strongest signals are searched and stored automatically in the
band number you have selected (FM1, FM2 or FM3).These stations are preset in the number
buttons — No. 1 (lowest frequency) to No. 6 (highest frequency).
When automatic preset is over, the station stored in number button 1 will be automatically
tuned in.
KD-S757R
KD-SX858R
“SSM” appears, then disappears when
automatic preset is over.
FM/AM
FM1 FM2 FM3
FM1 FM2 FM3 AM
SSM
F M
EN06-12.KD-SX858R/S757R[E]/1 98.10.9, 5:38 PM7

8
Manual preset
You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually.
EXAMPLE: Storing an FM station of 88.3 MHz into the preset number 1 of the FM1 band
1
Select the FM1 band.
2
Tune into a station of 88.3 MHz.
See page 6 to tune into a station.
3
Press and hold the number button (in this
example, 1) for more than 2 seconds.
4
1
3
2
KD-SX858R
Repeat the above procedure to store other stations into other
preset numbers.
Notes:
• A previously preset station is erased when a new station is stored in the same preset number.
• Preset stations are erased when the power supply to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset the stations again.
KD-S757R
FM/AM
F M
“P1” flashes for a few seconds.
EN06-12.KD-SX858R/S757R[E]/1 98.10.9, 5:38 PM8

9
ENGLISH
1
1
Select the band (FM1, FM2, FM3
or AM) you want.
2
Select the number (1 – 6) for the preset station you want.
To change the display information while receiving an FM RDS
station
Press DISP. Each time you press the button, the display changes as follows:
Tuning into a preset station
You can easily tune into a preset station.
Remember that you must store stations first.If you have not stored them yet, see pages 7 and 8.
KD-SX858R FM1 FM2 FM3 AM
2
1
Selecting FM reception sound
When an FM stereo broadcast is hard to receive:
Press MO/RND (Mono/Random) while listening to an FM stereo broadcast.The MO (Mono)
indicator lights up on the display and the sound you hear becomes monaural but reception
will be improved.
To restore the stereo effect, press the same button again.
Station name PTY (Programme type)
Frequency Clock time
MO/RND
Lights up when receiving an FM broadcast in stereo.
MO/RND
KD-S757R
FM/AM
KD-S757R
AM
A M
F M
FM1 FM2
FM3
KD-SX858R DISP
EN06-12.KD-SX858R/S757R[E]/1 98.10.9, 5:38 PM9

10
What you can do with RDS EON
RDS OPERATIONS
RDS (Radio Data System) allows FM stations to send an additional signal along with their
regular programme signals. For example, the stations send their station names, as well as
information about what type of programme they broadcast, such as sports or music, etc.
Another advantage of RDS function is called “EON (Enhanced Other Networks).” The EON
indicator lights up while receiving an FM station with the EON data. By using the EON data
sent from a station, you can tune into a different station of a different network broadcasting
your favorite programme or traffic announcement while listening to another programme or to
another source such as CD.
By receiving the RDS signals, this unit can do the following:
• Tracing the same programme automatically (Network-Tracking Reception)
• Standby Reception of TA (Traffic Announcement) or your favorite programme
• PTY (Programme Type) search
• TA (Traffic Announcement) search
• And some other functions
Tracing the same programme automatically (Network-
Tracking Reception)
Whendriving inanareawhereFM reception is not good,thetunerbuiltin this unit automatically
tunes in another RDS station, broadcasting the same programme with stronger signals. So,
you can continue to listen to the same programme in its finest reception, no matter where you
drive. (See the illustration on the next page.)
Two types of the RDS signals are used to make Network-Tracking Reception work correctly
— PI (Programme Identification) and AF (Alternative Frequency) data.
Without receiving these data correctly from the RDS station you are listening to, Network-
Tracking Reception will not operate.
To use Network-Tracking Reception, press and hold TP/RDS (Traffic
Programme/Radio Data System) for more than 1 second. Each time you
press and hold the button, Network-Tracking Reception modes change as
follows: Mode 1 Mode 2 Mode 3
TP
RDS
EN06-12.KD-SX858R/S757R[E]/1 98.10.9, 5:38 PM10

11
ENGLISH
Mode 1 (AF:on / REG:off)
Network-Tracking is activated with Regionalization set to “off.”
Switches to another station within the same network when the receiving
signals from the current station become weak.
Note:
In this mode, the programme may differ from the one currently received.
Mode 2 (AF:on / REG:on)
Network-Tracking is activated with Regionalization set to “on.”
Switchestoanotherstation, within the same network, broadcasting the same
programmewhenthe receiving signals from thecurrentstationbecomeweak.
Mode 3 (AF:off / REG:off)
Network-Tracking is deactivated.
The same programme can be received on different frequencies.
Programme 1 broadcasting on
frequency B
Programme 1 broadcasting
on frequency A
Programme 1 broadcasting on frequency D
Programme 1 broadcasting on frequency C
Programme 1 broadcasting on frequency E
EN06-12.KD-SX858R/S757R[E]/1 98.10.9, 5:38 PM11

12
Using Standby Reception
Standby Reception allows the unit to switch temporarily to your favorite programme (PTY:
ProgrammeType)andTrafficAnnouncement(TA) from the current source (another FMstation
and CD).
Note:
Standby Reception will not work if you are listening to anAM station.
TA Standby Reception
• When you pressTP/RDS while listening to an FM station, theTP indicator
islitduringreception of aTP (TrafficProgramme) station and theTAstandby
mode is engaged.
Note:
When the station being received is not a TP station, the TP indicator flashes. Press
¢or 4to engage the TA standby mode. “SEARCH” appears on the
display, and TP station search starts. When aTP station is tuned in, the TP indicator
is lit.
• If you are listening to a CD, and wish to listen to aTP station, press
TP/RDS to enter the TA standby mode.(The TP indicator lights up.)
Ifatrafficprogramme startsbroadcastingwhiletheTA standby mode isactive,
“TRAFFIC” appears and the playback source changes to the FM band.The
volume increases to the preset TA volume level and the traffic programme
can be heard (see page 16).
To deactivate the TA standby mode, press TP/RDS again.
PTY Standby Reception
• When you press PTY while listening to an FM station, the PTY indicator is
litduringreception of a PTY station and thePTYstandby mode is engaged.
The selected PTY name stored on page 13 flashes for 5 seconds.
Note:
When the station being received is not a PTY station, the PTY indicator flashes.
Press ¢or 4to engage the PTY standby mode. “SEARCH” appears on
the display, and PTY station search starts. When a PTY station is tuned in, the PTY
indicator is lit.
• If you are listening to a CD, and wish to listen to a selected PTY broadcast,
press PTY to enter the PTY standby mode. (The PTY indicator lights up.)
If the selected PTY programme starts broadcasting while the PTY standby
mode is active, the selected PTY name appears and the playback source
changes to the FM band.The selected PTY programme can then be heard.
To deactivate the PTY standby mode, press PTY again.
TP
RDS
PTY
EN06-12.KD-SX858R/S757R[E]/1 98.10.9, 5:38 PM12

13
ENGLISH
1
Press and hold the button for more than 2
seconds to call up the general settings mode
(see page 27).
2
Select “PTY STBY(Standby)” if not shown on
the display.
3
Select one of twenty-nine PTY codes. (See
the table on page 17.)
Selected code name appears on the display and is stored
into memory.
4
Finish setting.
Searching Your Favorite Programme
You can search one of your 6 favorite programme types stored in memory.
When shipped from the factory, the following 6 programme types have been stored in the
number buttons (1 to 6).
To change the factory preset settings, see page 14.
To search your favorite programme, see page 15.
Selecting Your Favorite Programme for PTY Standby
Reception
You can select your favorite programme for PTY Standby Reception to store in memory.
When shipped from the factory, “NEWS” is stored as the programme type for PTY Standby
Reception.
POP M
123456
CLASSICS AFFAIRS VARIED
ROCK M EASY M
SEL
1, 4 2
3
SEL
SEL
EN13-17.KD-SX858R/S757R[E]/1 98.10.13, 4:02 PM13

14
To store your favorite programme types
1
Press and hold the button for more than 2
seconds to call up the general settings mode
(see page 27).
2
Select “PTY SRCH(Search)” if not shown on
the display.
3
Select one of twenty-nine PTY codes. (See
the table on page 17.)
Selected code name appears on the display.
• If the code already stored in memory is selected, it will
flash on the display.
4
Press and hold the number button for more than 2 seconds to
store the PTY code selected into the preset number you want.
The PTY code starts flashing.
5
Finish setting.
1, 5 2
3
4
SEL
SEL
SEL
EN13-17.KD-SX858R/S757R[E]/1 98.10.13, 4:02 PM14

15
ENGLISH
1
Press and hold the button for more than 1
second while listening to an FM station.
The last selected PTY code appears.
2
Select one of the PTY codes stored in the
preset number buttons (1 to 6).
PTY search for your favorite programme starts after 5
seconds.
• If there is a station broadcasting a programme of the same PTY code you have selected,
that station is tuned in.
• If there is no station broadcasting a programme of the same PTY code you have selected,
the station will not change.
Note:
In some areas, the PTY search will not work correctly.
To search your favorite programme type
21
PTY
Ex.When “CLASSICS” is stored in the preset number button 2.
EN13-17.KD-SX858R/S757R[E]/1 98.10.13, 4:02 PM15

16
Other convenient RDS functions
Automatic selection of the station when using the number
buttons
Usually when you press the number button, the preset station is tuned in.
However, when the preset station is an RDS station, something different will happen. If the
signals from that preset station are not sufficient for good reception, this unit starts searching
anotherstation broadcastingthesameprogramme astheoriginal presetstationisbroadcasting,
then if any station broadcasting the same programme is found, the station will be tuned in.
Changing the display mode while listening to an FM
station
You can change the initial indication on the display to station frequency, station name (PS), or
clock time while listening to an FM RDS station.
• See also “Changing the general settings”on page 27.
1. Press and hold SEL (select) for more than 2 seconds to call up the general settings mode.
2. Select “DISPMODE” with ¢or 4.
3. Setto the desired indication (station name,stationfrequencyor clock time) with the control
dial.
Note:
By pressing DISP, you can also change the display while listening to an FM RDS station.
Each time you press the button, the display changes to show the following:
* The display returns to the initially preset mode after a short while.
Setting the TA volume level
You can preset the volume level for TA Standby Reception. When a traffic programme is
received, the volume level automatically changes to the preset level.
• See also “Changing the general settings”on page 27.
1. Press and hold SEL (select) for more than 2 seconds to call up the general settings mode.
2. Select “TA VOL” with ¢or 4.
3. Set to the desired volume level with the control dial.
Station name PTY (Programme type)
Frequency Clock time
EN13-17.KD-SX858R/S757R[E]/1 98.10.13, 4:02 PM16

17
ENGLISH
Automatic clock adjustment
When shipped from the factory, the clock built in this unit is set to be readjusted automatically
using the CT (Clock Time) data in the RDS signal.
If you do not want to use automatic clock adjustment, follow the procedure below.
• See also “Changing the general settings” on page 27.
1. Press and hold SEL (select) for more than 2 seconds to call up the general settings mode.
2. Select “AUTO ADJ” with ¢or 4.
3. Select “ADJ OFF” by turning the control dial counterclockwise.
Now automatic clock adjustment is canceled.
To reactivate clock adjustment, repeat the same procedure and select “ADJ ON” in step 3
by turning the control dial clockwise.
Note:
It takes about 2 minutes to adjust the time using the CT data. So, you must tune to the station for more
than 2 minutes continuously; otherwise, the clock time will not be adjusted.
PTY codes
NEWS: News
AFFAIRS: Topical programmes
expanding on current news
or affairs
INFO: Programmes which impart
advice on a wide variety of
topics
SPORT: Sport events
EDUCATE: Educational programmes
DRAMA: Radio plays
CULTURE: Programmes on national or
regional culture
SCIENCE: Programmes on natural
science and technology
VARIED: Other programmes like
comedies or ceremonies
POP M: Pop music
ROCK M: Rock music
EASY M: Easy-listening music
LIGHT M: Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce,
trading, the Stock Market,
etc.
CHILDREN: Entertainment programmes
for children
SOCIAL: Programmes on social
activities
RELIGION: Programmes dealing with
any aspect of belief or faith,
or the nature of existence or
ethics
PHONE IN: Programmes where people
can express their views
either by phone or in a
public forum
TRAVEL: Programmes about travel
destinations, package tours,
and travel ideas and
opportunities
LEISURE: Programmes concerned with
recreational activities such
as gardening, cooking,
fishing, etc.
JAZZ: Jazz music
COUNTRY: Country music
NATION M: Current popular music from
another nation or region, in
that country’s language
OLDIES: Classic pop music
FOLK M: Folk music
DOCUMENT: Programmes dealing with
factual matters, presented in
an investigative style
EN13-17.KD-SX858R/S757R[E]/1 98.10.13, 4:02 PM17

18
CD OPERATIONS
Playing a CD
Insert a disc into the loading slot.
The unit turns on, draws a CD and starts playback
automatically.
Loading slot
Total playing time of
the inserted disc Total track number of the inserted disc Elapsed playing time Current track
Note on One-Touch Operation:
When a CD is already in the loading slot, pressing CD turns on the unit and starts playback
automatically.
To stop play and eject the CD
Press 0.
CD play stops and the CD automatically ejects from the loading slot.
If you change the source to FM or AM (or CD changer:ONLY FOR KD-SX858R), the CD play
also stops (without ejecting the CD this time).
Notes:
• If the ejected disc is not removed for about 15 seconds, the disc is automatically inserted again into
the loading slot to protect it from dust. (CD play will not start this time.)
• You can eject the CD even when the unit is turned off.
Note:
When a CD is inserted upside down, “EJECT” appears on the display and the CD ejects automatically.
0
EN18-21.KD-SX858R/S757R[E]/1 98.10.13, 4:03 PM18

19
ENGLISH
Locating a track or a particular portion on a CD
Number buttons¢
4
To fast forward or reverse the track
Press and hold ¢, while playing a CD, to fast forward the track.
Press and hold 4, while playing a CD, to reverse the track.
To go to the next track or the previous track
Press ¢briefly, while playing a CD, to go ahead to the beginning of
thenexttrack.Eachtime you pressthebuttonconsecutively, thebeginning
of the next track is located and played back.
Press 4briefly, while playing a CD, to go back to the beginning of
the current track. Each time you press the button consecutively, the
beginning of the previous track is located and played back.
To go to a particular track directly
Pressthe number buttoncorrespondingto thetracknumberto startplayback.
• To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1 second.
7 8 9 10 11 12
EN18-21.KD-SX858R/S757R[E]/1 98.10.13, 4:03 PM19

20
Selecting CD playback modes
RPT
MO/RND
To play back tracks at random (Random Play)
You can play back all tracks on the CD at random.
Each time you press MO/RND (Mono/Random) while playing a CD, CD
random play mode turns on and off alternately.
When the random mode is turned on, the RND indicator lights up on the
display and a track randomly selected starts playing.
• To select the next track at random, press ¢briefly.
To play back tracks repeatedly (Repeat Play)
You can play back the current track repeatedly.
Each time you press RPT (Repeat) while playing a CD, CD repeat play
mode turns on and off alternately.
When the repeat mode is turned on, the RPT indicator lights up on the
display.
RPT
MO/RND
Track number of the currently playing track
EN18-21.KD-SX858R/S757R[E]/1 98.10.13, 4:03 PM20