JVC UX-F2BEN User manual

SERVICE MANUAL
COPYRIGHT © 2010 Victor Company of Japan, Limited No.MB736<Rev.003>
2010/6
MICRO COMPONENT SYSTEM
MB736<Rev.003>20106SERVICE MANUAL
UX-F2BE, UX-F2BEN, UX-F2BEV,
UX-F2BUS, UX-F2BUW
COPYRIGHT © 2010 Victor Company of Japan, LimitedLead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
2
SP-UXF2B SP-UXF2B
CA-UXF2B
only for Europe

1-2 (No.MB736<Rev.003>)
SPECIFICATION
Design and specifications are subject to change without notice.
For Europe(Main unit CA-UXF2B)
General
Power source AC 230 V , 50 Hz
Power consumption (at operation) 40 W
Power consumption (on standby) 1.00 W or less
Dimensions (approx.) (W x H x D) (including projecting parts) 236 mm ×123 mm ×285 mm
Mass (approx.) 2.0 kg
Amplifier
Output Power 100 W (50 W + 50 W) at 6 Ω(10% THD)
Audio Input AUDIO IN: Stereo mini (Ø3.5 mm)
Speaker impedance 6 Ω- 16 Ω
Tuner
FM frequency 87.50 MHz - 108.00 MHz
USB
USB specification Compatible with USB 2.0 Full Speed
Compatible device Mass storage class
Compatible system FAT16, FAT32
Output power DC 5 V 500 mA
SD
Compatible device SD, SDHC
Compatible system FAT16, FAT32
Speaker SP-UXF2B
Speaker type Bass-reflex type
Tweeter 4 cm
Woofer 12 cm
Impedance 6 Ω
Dimensions (approx.) (W x H x D) (including projecting parts) 141 mm ×250 mm ×181 mm
Mass (approx.) 1.8 kg each

(No.MB736<Rev.003>)1-3
SPECIFICATION
Design and specifications are subject to change without notice.
For Asia(Main unit CA-UXF2B)
General
Power source AC 110 - 127 V/AC 220 - 240 V (adjustable with the voltage selector),
50 Hz/60 Hz
Power consumption (at operation) 40 W
Power consumption (on standby) 1.00 W or less
Dimensions (approx.) (W x H x D) (including projecting parts) 236 mm ×123 mm ×285 mm
Mass (approx.) 2.0 kg
Amplifier
Output Power 100 W (50 W + 50 W) at 6 Ω(10% THD)
Audio Input AUDIO IN: Stereo mini (Ø3.5 mm)
Speaker impedance 6 Ω- 16 Ω
Tuner
FM frequency 87.50 MHz - 108.00 MHz
AM frequency 531 kHz - 1 710 kHz (at 9 kHz intervals)
530 kHz - 1 710 kHz (at 10 kHz intervals)
USB
USB specification Compatible with USB 2.0 Full Speed
Compatible device Mass storage class
Compatible system FAT16, FAT32
Output power DC 5 V 500 mA
SD
Compatible device SD, SDHC
Compatible system FAT16, FAT32
Speaker SP-UXF2B
Speaker type Bass-reflex type
Tweeter 4 cm
Woofer 12 cm
Impedance 6 Ω
Dimensions (approx.) (W x H x D) (including projecting parts) 141 mm ×250 mm ×181 mm
Mass (approx.) 1.8 kg each

1-4 (No.MB736<Rev.003>)
SECTION 1
PRECAUTION
1.1 Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purpos-
es. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be per-
formed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteris-
tics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by us-
ing replacement components rated for higher voltage, watt-
age, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Ser-
vice Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety charac-
teristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassem-
bling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isola-
tion check on the exposed metal parts of the product (an-
tenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particular-
ly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage cur-
rent must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ωper volt or more sensitivity
in the following manner. Connect a 1,500Ω10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
1.2 Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3 Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of pre-
forming repair of this system.
1.4 Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
Good earth ground
Place this
probe on
each exposed
metal part.
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
1500 10W
0.15 F AC TYPE

(No.MB736<Rev.003>)1-5
1.5 Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.5.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.6 Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.7 Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land sections before the card wire is disconnected from the connector on the servo board. (If the card wire
is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land sections after connecting the card wire.
1M
Conductive material
(conductive sheet) or iron palate
(caption)
Anti-static wrist strap
solder short part

1-6 (No.MB736<Rev.003>)
1.8 Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
REPRODUCTION AND POSITION OF LABELS and PRINT
!Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
WARNING LABEL and PRINT

(No.MB736<Rev.003>)1-7
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
SECTION 3
DISASSEMBLY
3.1 Main body (Used model: UX-F2E)
3.1.1 Removing the Top cover (See Fig.1, 2, 3)
(1) Remove the four screws Aattaching the Top cover. (See
Fig.1)
Fig.1
(2) Remove the two screws Band two screws Cattaching both
side of the Top cover. (See Fig.2)
Fig.2
(3) Remove the three screws Dand three screws E attaching
the Top cover. (See Fig.3)
Fig.3
3.1.2 Removing the Main board (See Fig.4)
(1) Disconnect the connector wire from Jack board connected
to connector CN606 of the Main board.
(2) Disconnect the connector wire from FAN connected to con-
nector CN612 of the Main board.
(3) Disconnect the card wire from Upgrade board connected to
connector CN605 of the Main board.
(4) Disconnect the connector wire from SMPS board connect-
ed to connector CN603 of the Main board.
(5) Disconnect the card wire from MPEG board connected to
connector CN609 of the Main board.
(6) Disconnect the connector wire from MPEG board connect-
ed to connector CN607 of the Main board.
(7) Disconnect the connector wire from SMPS board connect-
ed to connector CN601 of the Main board.
(8) Disconnect the card wire from Display board connected to
connector CN602 of the Main board.
(9) Disconnect the card wire from Tuner pack connected to
connector CN604 of the Main board.
(10) Remove the five screws Fattaching the Main board.
Fig.4
A
A
B
C
D
E
F
F
F
F
F
CN606 CN605CN604
CN612 CN603
CN609
CN607
CN601
CN602

1-8 (No.MB736<Rev.003>)
3.1.3 Removing the SMPS board (See Fig.5, 6)
(1) Disconnect the connector wire from Display board connect-
ed to connector CN902 of the SMPS board. (See Fig.5)
Fig.5
(2) Remove the two screws G, one screw Hand one screw J
attaching the SMPS board. (See Fig.6)
Fig.6
3.1.4 Removing the CD mechanism (See Fig.7, 8, 9, 10, 11)
(1) Remove the one screw Kand one screw Lattaching the
Rear cabinet bracket. (See Fig.7)
Fig.7
(2) Remove the two screws Mand two screws Nattaching the
CD mechanism. (See Fig.8)
Fig.8
(3) Disconnect the connector wire from MPEG board connect-
ed to connector of Loader board. (See Fig.9)
Fig.9
(4) Solder the short part of the Pickup board. (See fig.10)
Fig.10
(5) Disconnect the card wire from CD mechanism connected
to connector CN102 of the MPEG board. (See Fig.11)
Fig.11
CN902
G
HJ
K
L
M
N
M
N
Loader boardconnector
solder short part
CN102

(No.MB736<Rev.003>)1-9
3.1.5 Removing the MPEG board (See Fig.12)
(1) Disconnect the card wire from USB board connected to
connector CN108 of the MPEG board.
(2) Remove the four screws Pattaching the MPEG board.
Fig.12
3.1.6 Removing the Front panel (See Fig.13, 14)
(1) Disengage one hook aengaged Front panel. (See Fig.13)
Fig.13
(2) Disengage two hooks bengaged both side of the Front
panel. (See Fig.14)
Fig.14
3.1.7 Removing the Jack board (See Fig.15)
(1) Remove the two screws Qattaching the Jack board.
Fig.15
3.1.8 Removing the USB board (See Fig.16)
(1) Disconnect the connector wire from Display board connect-
ed to connector CN203 of the USB board.
(2) Remove the two screws Rattaching the USB board.
Fig.16
3.1.9 Removing the Display board (See Fig.17)
(1) Remove the twelve screws Sattaching the Display board.
Fig.17
CN108
P
P
P
hook a
hook b
Q
R
CN203
S
S
S
S

1-10 (No.MB736<Rev.003>)
SECTION 4
ADJUSTMENT
This service manual does not describe ADJUSTMENT.
SECTION 5
TROUBLESHOOTING
This service manual does not describe TROUBLESHOOTING.

(No.MB736<Rev.003>)1-11

(No.MB736<Rev.003>)
VSE
Printed in Japan
Victor Company of Japan, Limited
Home Entertainment Business Division Personal AV Operation 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan

REVISION INFORMATION
MICRO COMPONENT SYSTEM
COPYRIGHT © 2010 Victor Company of Japan, Limited MB736-R002
2010/04
UX-F2BE, UX-F2BEN, UX-F2BEV
■OVERVIEW
Add UX-F2BEV.
■DETAILS
COVER SECTION
Title Line No.MB736<Rev.001> No.MB736<Rev.002> Description
Revision Rev.001 Rev.002
Model No. UX-F2BE, UX-F2BEN UX-F2BE, UX-F2BEN, UX-F2BEV
SECTION 1 PRECAUTION
Title Line No.MB736<Rev.001> No.MB736<Rev.002> Description
1.1 Safety
Precautions
3 3. Many electrical and mechanical parts
in the products have special safety-
related characteristics. These
characteristics are often not evident from
visual inspection nor can the protection
afforded by them necessarily be obtained
by using replacement components rated
for higher voltage, wattage, etc.
Replacement parts which have these
special safety characteristics are
identified in the Parts List of Service
Manual. Electrical components having
such features are identified by shading
on the schematics and by ( ) on the Parts
List in the Service Manual. The use of a
substitute replacement which does not
have the same safety characteristics as
the recommended replacement parts
shown in the Parts List of Service Manual
may create shock, fire, or other hazards.
3. Many electrical and mechanical parts
in the products have special safety-
related characteristics. These
characteristics are often not evident from
visual inspection nor can the protection
afforded by them necessarily be obtained
by using replacement components rated
for higher voltage, wattage, etc.
Replacement parts which have these
special safety characteristics are
identified in the Parts List of Service
Manual. Electrical components having
such features are identified by shading
on the schematics and by
( ILLUSTRATION(kigo001.png) ) on the
Parts List in the Service Manual. The use
of a substitute replacement which does
not have the same safety characteristics
as the recommended replacement parts
shown in the Parts List of Service Manual
may create shock, fire, or other hazards.

2 (MB736-R002)
PARTS LIST
MODEL No. LIST
Model No. No.MB736<Rev.002>
UX-F2BE 01
UX-F2BEN 02
UX-F2BEV 03
General assembly [M1MM]
Part No.
!Symbol or <Rev.001> <Rev.002> Part Name Description Qty Models
M1MM 76 ------------ CD7111091800300 RATING LABEL (Addition) 1 03
Packing and accessories [M3MM]
Part No.
!Symbol or <Rev.001> <Rev.002> Part Name Description Qty Models
M3MM A1 ------------ CD7202091801200 INST BOOK (Addition) 1 03
M3MM A2 ------------ CD7202091801300 INST BOOK (Addition) 1 03
M3MM A3 ------------ CD7202091801400 INST BOOK (Addition) 1 03
M3MM A4 ------------ CD7202091801500 INST BOOK (Addition) 1 03
M3MM A6 ------------ CD7201091900300 SAFETY SHEET (Addition) 1 03
Electrical parts list Main board [01]
Part No.
!Symbol or <Rev.001> <Rev.002> Part Name Description Qty Models
01 U601 1506780515000-H 1506780527010-B IC 1 01,02,03

(MB736-R002) 3

Victor Company of Japan, Limited
Home Entertainment Business Division Personal AV Operation 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(MB736-R002) Printed in Japan
No.MB736<Rev.001> VSE

REVISION INFORMATION
MICRO COMPONENT SYSTEM
COPYRIGHT © 2010 Victor Company of Japan, Limited MB736-R003
2010/06
UX-F2BE, UX-F2BEN, UX-F2BEV,
UX-F2BUS, UX-F2BUW
■OVERVIEW
Add UX-F2BUS and UX-F2BUW.
■DETAILS
COVER SECTION
Title Line No.MB736<Rev.002> No.MB736<Rev.003> Description
Revision Rev.002 Rev.003
Issue Date 2010/04 2010/06
Model No. UX-F2BE, UX-F2BEN, UX-F2BEV UX-F2BE, UX-F2BEN, UX-F2BEV,
UX-F2BUS, UX-F2BUW
Cover Illustration ILLUSTRATION(mb736_0001.png) ILLUSTRATION(mb736_0001.png)
SPECIFICATION 2
Main unit CA-UXF2B
For Europe(Main unit CA-UXF2B)
SPECIFICATION T - SPECIFICATION
2 - For Asia(Main unit CA-UXF2B)
3 - General
4 - Power source
AC 110 - 127 V/AC 220 - 240 V (adjustable with
the voltage selector), 50 Hz/60 Hz
5 - Power consumption (at operation)
40 W
6 - Power consumption (on standby)
1.00 W or less
7 - Dimensions (approx.) (W x H x D) (including
projecting parts)
236 mm × 123 mm × 285 mm
8 - Mass (approx.)
2.0 kg
9 - Amplifier

2 (MB736-R003)
Title Line No.MB736<Rev.002> No.MB736<Rev.003> Description
10 - Output Power
100 W (50 W + 50 W) at 6 Ω(10% THD)
11 - Audio Input
AUDIO IN: Stereo mini (Φ3.5 mm)
12 - Speaker impedance
6 Ω- 16 Ω
13 - Tuner
14 - FM frequency
87.50 MHz - 108.00 MHz
15 - AM frequency
531 kHz - 1 710 kHz (at 9 kHz intervals)
16 - 530 kHz - 1 710 kHz (at 10 kHz intervals)
17 - USB
18 - USB specification
Compatible with USB 2.0 Full Speed
19 - Compatible device
Mass storage class
20 - Compatible system
FAT16, FAT32
21 - Output power
DC 5 V 500 mA
22 - SD
23 - Compatible device
SD, SDHC
24 - Compatible system
FAT16, FAT32
25 - Speaker SP-UXF2B
26 - Speaker type
Bass-reflex type
27 - Tweeter
4 cm
28 - Woofer
12 cm
29 - Impedance
6 Ω
30 - Dimensions (approx.) (W x H x D) (including
projecting parts)
141 mm × 250 mm × 181 mm
31 - Mass (approx.)
1.8 kg each
33 - Design and specifications are subject to change
without notice.

(MB736-R003) 3
PARTS LIST
MODEL No. LIST
Model No. No.MB736<Rev.003>
UX-F2BE 01
UX-F2BEN 02
UX-F2BEV 03
UX-F2BUS 04
UX-F2BUW 05
General assembly [M1MM]
Part No.
!Symbol or <Rev.002> <Rev.003> Part Name Description Qty Models
M1MM 3 ------------ CD6033226080110 SCREW (Addition) 2 04,05
M1MM 6 ------------ CD5001091800200 FRONT CABINET (Addition) 1 04,05
M1MM 8 ------------ CD5403091800101 BUTTON SET (Addition) 1 04,05
M1MM 14 ------------ CD5633091800101 REAR CABINET
BRACKET (Addition) 1 04,05
M1MM 17 ------------ CD5002091800300 REAR CABINET (Addition) 1 04,05
M1MM 21 ------------ CD5416091800101 BTN SD/USB REC (Addition) 2 04,05
M1MM 23 ------------ CD5404091800101 FUNCTION BUTTON (Addition) 1 04,05
M1MM 24 ------------ CD5627091800101 FUNCTION BTN BKT (Addition) 1 04,05
M1MM 33 ------------ CD5002091800401 BOTTOM CABINET (Addition) 1 04,05
M1MM 35 ------------ CD6013230060300 SCREW (Addition) 1 04,05
M1MM 43 ------------ CD3801000000360 FM TUNER MODULE (Addition) 1 04,05
M1MM 62 ------------ CD3002100160900 FFC CABLE (Addition) 1 04,05
M1MM 63 ------------ CD3002140160910 FFC CABLE (Addition) 1 04,05
M1MM 73 ------------ CD3505070523000 HOUSING SHILED (Addition) 1 04,05
M1MM 76 ------------ CD7111091800200 RATING LABEL (Addition) 1 04
M1MM 76 ------------ CD7111091800400 RATING LABEL (Addition) 1 05
M1MM 78 ------------ CD3307020200010 VOLTAGE SELECT SW (Addition) 1 04,05
M1MM 79 ------------ CD5902050700600 SWITCH COVER (Addition) 1 04,05
M1MM 80 ------------ CD6013226080100 SCREW (Addition) 2 04,05
M1MM 81 ------------ CD3501020083900 CONNECTOR WIRE (Addition) 1 04,05
M1MM 82 ------------ CD2712065040000 FERRITE CORE (Addition) 1 04,05
Packing and accessories [M3MM]
Part No.
!Symbol or <Rev.002> <Rev.003> Part Name Description Qty Models
M3MM A1 ------------ CD7202091800500 INST BOOK (Addition) 1 04,05
M3MM A2 ------------ CD7202091800600 INST BOOK (Addition) 1 04
M3MM A2 ------------ CD7202091801600 INST BOOK (Addition) 1 05
M3MM A3 ------------ CD7202091801700 INST BOOK (Addition) 1 05
M3MM A6 ------------ CD7201091900400 SAFETY SHEET (Addition) 1 04,05
M3MM A11 ------------ CD5926081000100 AM LOOP ANT (Addition) 1 04,05
M3MM A12 ------------ CD3103000000020 CONVERSION PLUG (Addition) 1 04,05
M3MM P4 ------------ CD7502081000100 POLY BAG (Addition) 2 04,05
M3MM P8 ------------ CD7501070900100 EPE SHEET (Addition) 2 04,05
M3MM P10 ------------ CD7215091800200 FLOUR PAPER (Addition) 2 04,05
Electrical parts list Main board [01]
Part No.
!Symbol or <Rev.002> <Rev.003> Part Name Description Qty Models
01 U602 ------------ CD1511002402080 IC (Addition) 1 04,05
01 C715 ------------ CD1121474064020 C CAPACITOR (Addition) 1 04,05
01 C716 ------------ CD1121474064020 C CAPACITOR (Addition) 1 04,05
01 C717 ------------ CD1121474064020 C CAPACITOR (Addition) 1 04,05
01 C718 ------------ CD1121474064020 C CAPACITOR (Addition) 1 04,05
01 C719 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C720 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C721 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C761 ------------ CD1121681081021 C CAPACITOR (Addition) 1 04,05
01 C762 ------------ CD1121681081021 C CAPACITOR (Addition) 1 04,05
01 C763 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C764 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C765 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C766 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C769 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05

4 (MB736-R003)
Part No.
!Symbol or <Rev.002> <Rev.003> Part Name Description Qty Models
01 C770 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
01 C780 ------------ CD1129226044120 C CAPACITOR (Addition) 1 04,05
01 C781 ------------ CD1129226044120 C CAPACITOR (Addition) 1 04,05
01 C796 ------------ CD1221000042050 C RESISTOR (Addition) 1 04,05
01 C797 ------------ CD1221000042050 C RESISTOR (Addition) 1 04,05
01 R780 ------------ CD1221103052020 C RESISTOR (Addition) 1 04,05
01 R782 ------------ CD1221104052020 C RESISTOR (Addition) 1 04,05
01 CF05 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
01 EC601 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
01 EC602 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
01 EC605 ------------ CD1132227053064 E CAPACITOR (Addition) 1 04,05
01 EC607 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
01 EC608 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
01 EC610 ------------ CD1132227053064 E CAPACITOR (Addition) 1 04,05
01 EC701 ------------ CD1132228073270 E CAPACITOR (Addition) 1 04,05
01 EC703 ------------ CD1132227053064 E CAPACITOR (Addition) 1 04,05
01 EC711 ------------ CD1132227053064 E CAPACITOR (Addition) 1 04,05
01 EC712 ------------ CD1132227053064 E CAPACITOR (Addition) 1 04,05
01 EC713 ------------ CD1132227053064 E CAPACITOR (Addition) 1 04,05
01 P601 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 04,05
01 P602 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 04,05
MPEG board [02]
Part No.
!Symbol or <Rev.002> <Rev.003> Part Name Description Qty Models
02 C135 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
02 C139 ------------ CD1121300081020 C CAPACITOR (Addition) 1 04,05
02 C140 ------------ CD1121300081020 C CAPACITOR (Addition) 1 04,05
02 C165 ------------ CD1121152082021 C CAPACITOR (Addition) 1 04,05
02 C166 ------------ CD1121102082021 C CAPACITOR (Addition) 1 04,05
Display board [03]
Part No.
!Symbol or <Rev.002> <Rev.003> Part Name Description Qty Models
03 C507 ------------ CD1132227053064 E CAPACITOR (Addition) 1 04,05
03 C510 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
03 C513 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
03 C526 ------------ CD1121474064020 C CAPACITOR (Addition) 1 04,05
03 C527 ------------ CD1132477043060 E CAPACITOR (Addition) 1 04,05
03 C537 ------------ CD1121474064020 C CAPACITOR (Addition) 1 04,05
03 C538 ------------ CD1132477043060 E CAPACITOR (Addition) 1 04,05
03 C539 ------------ CD1132477043060 E CAPACITOR (Addition) 1 04,05
03 R503 ------------ CD1221181022050 C RESISTOR (Addition) 1 04,05
03 R536 ------------ CD1221203062020 C RESISTOR (Addition) 1 04,05
03 R544 ------------ CD1221000042050 C RESISTOR (Addition) 1 04,05
SMPS board [04]
Part No.
!Symbol or <Rev.002> <Rev.003> Part Name Description Qty Models
04 C907 ------------ CD1116103192000 C CAPACITOR (Addition) 1 04,05
04 C918 ------------ CD1116103192000 C CAPACITOR (Addition) 1 04,05
04 C924 ------------ CD1132108053161 E CAPACITOR (Addition) 1 04,05
04 C925 ------------ CD1132108053161 E CAPACITOR (Addition) 1 04,05
04 C926 ------------ CD1132337063220 E CAPACITOR (Addition) 1 04,05
04 C927 ------------ CD1132337063220 E CAPACITOR (Addition) 1 04,05
04 C928 ------------ CD1132337063220 E CAPACITOR (Addition) 1 04,05
04 C931 ------------ CD1132107053063 E CAPACITOR (Addition) 1 04,05
04 L902 ------------ CD2104000000340 LINE FILTER (Addition) 1 04,05
!04 F901 ------------ CD2003250250410 FUSE (Addition) 1 04,05
04 PIN3 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 04,05
04 PIN4 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 04,05
04 PIN5 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 04,05
04 SW901 ------------ CD3101790221000 CONNECTOR WIRE (Addition) 1 04,05