JVC UX-G800D User manual

MICRO COMPONENT SYSTEM
UX-G800D
GVT0250-001A
[B]
—Consists of CA-UXG800D and SP-UXG300
INSTRUCTIONS
Cover_UX-G800D[B]3.indd 1Cover_UX-G800D[B]3.indd 1 2/21/08 6:34:07 PM2/21/08 6:34:07 PM

G-1
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet.
There are no user serviceable parts inside the unit;
leave all servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser
radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
Warnings, Cautions and Others
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power
point, then obtain an appropriate safety approved
extension lead or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to
remove the fuse and dispose of the plug immediately,
to avoid a possible shock hazard by inadvertent
connection to the mains supply.
If this product is not supplied fitted with a mains plug
then follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which
is marked with the letter E or by the safety earth
symbol or coloured green or green-and-yellow.
The wires in the mains lead on this product are
coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As these colours may not correspond with the
coloured markings identifying the terminals in your
plug proceed as follows:
The wire which is coloured blue must be connected
to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be
connected to the terminal which is marked with the
letter L or coloured red.
IF IN DOUBT - CONSULT A COMPETENT
ELECTRICIAN.
CAUTION
The button in any position does not disconnect the
mains line.
Disconnect the mains plug to shut the power off
completely (the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain
readily operable.
• When the System is on standby, the STANDBY lamp
lights red.
• When the System is turned on, the STANDBY lamp
goes off.
The power can be remote controlled.
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Dear Customer,
This apparatus is in conformance with the valid
European directives and standards regarding
electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan,
Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
CAUTION:
• Do not block the ventilation openings or holes. (If
the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able
to get out.)
• Do not place any naked flame sources, such as
lighted candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws
governing the disposal of these batteries must be
followed strictly.
• Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
• Excessive sound pressure from earphones or
headphones can cause hearing loss.
Safety_UX-G800D[B]f.indd 1Safety_UX-G800D[B]f.indd 1 4/2/08 9:52:59 AM4/2/08 9:52:59 AM

G-2
Information for Users on Disposal of Old equipment
[European Union]
Attention:
This symbol is only valid in
the European Union.
This symbol indicates that the electrical and electronic equipment should not be
disposed as general household waste at its end-of-life. Instead, the product should
be handed over to the applicable collection point for the recycling of electrical and
electronic equipment for proper treatment, recovery and recycling in accordance
with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health which could otherwise be caused by inappropriate waste handling of this
product, please contact your local municipal office, your household waste disposal
service or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page www.jvc-europe.
com to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country for the treatment of old electrical
and electronic equipment.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a
height of 10 cm or more.
Front view Side view
Safety_UX-G800D[B]f.indd 2Safety_UX-G800D[B]f.indd 2 4/3/08 11:13:09 AM4/3/08 11:13:09 AM

1
Contents
Precautions ...................................................................... 2
Getting Started ................................................................ 2
Supplied Accessories ................................................................................... 2
Prepare the Remote Control........................................................................ 2
Connections ................................................................................................ 3
Basic and Common Operations ...................................... 5
Playing Back a Disc/USB Mass Storage Class Device .... 7
Loading a Disc ............................................................................................. 7
Connecting a USB Mass Storage Class Device .............................................. 7
Basic Disc/USB Mass Storage Class Device Operations ................................. 7
Playing Repeatedly—Repeat Play ............................................................. 8
Programming the Playing Order—Program Play....................................... 8
Playing at Random—Random Play............................................................ 8
Prohibiting Disc Ejection ............................................................................. 8
Listening to the Radio ..................................................... 9
Basic Tuner Operations................................................................................ 9
Presetting Stations and Services ................................................................. 9
What is DAB System? .................................................................................. 10
Changing the DAB Information ................................................................... 10
Improving the DAB Reception..................................................................... 10
Scanning Ensembles ................................................................................... 10
Receiving FM Stations with Radio Data System........................................... 11
Changing the Radio Data System Information ............................................ 11
Searching for Programs by PTY Codes (PTY Search)..................................... 11
Switching Temporarily to a Program of Your Choice Automatically ............ 11
Listening to Digital Audio Player ................................... 12
Setting the Clock and Using Timers ............................... 13
Setting the Clock......................................................................................... 13
Setting the Sleep Timer............................................................................... 13
Turning Off the System Automatically—AUTO STANDBY function............. 13
Setting the Daily Timer ............................................................................... 14
Troubleshooting.............................................................. 15
Learning More about This System ................................. 16
Maintenance .................................................................... 19
Specifications................................................................... 19
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the
best possible performance from the unit.
EN01-12_UX-G800D[B]3.indd 1EN01-12_UX-G800D[B]3.indd 1 2/21/08 6:34:41 PM2/21/08 6:34:41 PM

2
Precautions
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXG300R (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed when shipped from
the factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
• DAB antenna (× 1)
• Core filter (× 1), see page 18 for details
If anything is missing, consult your dealer immediately.
Prepare the Remote Control
When you use the remote control for the first time, pull
out the insulation sheet.
To Replace the Battery in the Remote Control
Notes on the power cord
• When you are away on travel or otherwise for an
extended period of time, remove the plug from the
wall outlet.
• When unplugging the System from the wall outlet,
always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the
System or moving the System.
• Do not alter, twist or pull the power cord, or put
anything heavy on it, which may cause fire, electric
shock, or other accidents.
• If the cord is damaged, consult a dealer and have the
power cord replaced with a new one.
Avoid moisture, water, dust, and high
temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult
your dealer. Using the System in this state may cause
a fire or electrical shock.
Getting Started
• Do not expose the System to direct sunlight or place
it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot
nor too cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to
vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires,
hairpins, coins, etc. into the System.
• Do not block the vents.
There are no user-serviceable parts inside. If
anything goes wrong, unplug the power cord and
consult your dealer.
NOTES:
•Store the battery in a place where children cannot reach.
If a child accidentally swallows the battery, consult a
doctor immediately.
•To prevent the battery from over-heating, cracking, or
starting a fire:
– Do not recharge, short, disassemble or heat the battery
or dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when
throwing away or saving it.
– Do not poke the battery with tweezers or similar tools.
•Dispose of battery in the proper manner, according to
federal, state, and local regulations.
•The batteries (battery pack or batteries installed) shall not
be exposed to excessive heat source such as sunshine, fire
or the like.
Lithium coin battery
(product number: CR2025)
Insulation sheet
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
EN01-12_UX-G800D[B]f.indd 2EN01-12_UX-G800D[B]f.indd 2 3/18/08 3:23:25 PM3/18/08 3:23:25 PM

3
Connections
Do not connect the AC power cord until all other connections have been made.
NOTES:
•Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep
the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor
reception.
•Make sure both the speakers are connected correctly and firmly.
•When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
•DO NOT connect more than one speaker to each terminal.
•DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
To a wall outlet
Plug the AC power cord only after all connections are complete.
Rear view
To connect the DAB antenna
(supplied)
Extend it so that you can receive your
desired ensembles.
For better DAB reception
Disconnect the supplied DAB antenna, and connect an active
antenna.
(See “Improving the DAB Reception” on page 10.)
DAB antenna (supplied)
EN01-12_UX-G800D[B]3.indd 3EN01-12_UX-G800D[B]3.indd 3 2/21/08 6:34:44 PM2/21/08 6:34:44 PM

4
Outdoor FM antenna
(not supplied)
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector (IEC or DIN45325).
FM antenna (supplied)
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
For better FM reception
To connect the AM loop antenna (supplied) To assemble the AM loop antenna
To connect the speaker cords
Press and hold
InsertRelease
Red
Black
From left
speaker
From right
speaker
EN01-12_UX-G800D[B]3.indd 4EN01-12_UX-G800D[B]3.indd 4 2/21/08 6:34:45 PM2/21/08 6:34:45 PM

5
Basic and Common Operations
Point at the remote sensor on the front panel.
(The operating range is approx. 7 m.)
STANDBY lamp
PHONES jack
Stereo mini plug cord
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden blast of sound
can damage your hearing, speakers and/or headphones when you turn on the System or start playback.
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
How to cancel the demonstration
Press and hold DEMO button while on standby. (Refer to the attached “Information about the demonstration
function.”)
EN01-12_UX-G800D[B]3.indd 5EN01-12_UX-G800D[B]3.indd 5 2/21/08 6:34:45 PM2/21/08 6:34:45 PM

6
To Press Indication/Result
System Remote
Turn on or off (standby)
the power
The STANDBY lamp on the System turns off/on.
Select a source See “Playing Back a Disc/USB Mass Storage Class Device” on
page 7.
See “Listening to the Radio” on page 9.
See “Listening to Digital Audio Player” on page 12.
Adjust the volume Adjustable range: Level 0 (“VOL MIN”) to level 40 (“VOL MAX”).
Drop the volume in a
moment —To restore the volume, press again, or adjust the volume level.
Activate the EALA
surround mode —
The indicator lights up.
To cancel this function, press repeatedly until indicator
lights off.
Emphasize the sound
(Sound Turbo function)
The S.TURBO indicator lights up.
To cancel this function, press again.
Reinforce the bass
sound (Active Hyper
Bass Pro function) —
Press and hold until the AHB indicator lights up.
• When Sound Turbo function is activated (see above), this
function cannot be activated.
To cancel this function, press and hold again when Sound
Turbo function is deactivated.
Adjust the tone (Bass/
Treble)
—
Press once for adjusting the bass level; twice for treble level,
then, press VOLUME +/–.
Adjustable range: –3 to +3.
Change the display
brightness —
Press when the System is turned on.
To cancel this function, press again.
Change the display
information (Clock and
Source)
—
For setting the clock, see “Setting the Clock and Using Timers”
on page 13.
• Not applicable for FM.
Set the ECO (ecology)
Mode
—
Press when the System is on standby.
Setting the ECO mode allows you to reduce power consumption
by turning the display off while on standby.
To cancel this function, press again when the System is on
standby.
EN01-12_UX-G800D[B]f.indd 6EN01-12_UX-G800D[B]f.indd 6 3/18/08 3:24:04 PM3/18/08 3:24:04 PM

7
Playing Back a Disc/USB Mass Storage Class Device
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or
recorded MP3/WMA files in ISO 9660 format.
– USB mass storage class device containing MP3/WMA
files.
• When playing back an MP3 or WMA track, MP3 or
WMA indicator lights up.
Loading a Disc (on the System only)
1Press to open the disc
tray.
2• When using an 8 cm
disc, place it on the
inner circle of the disc
tray.
3Press to close the disc
tray.
Connecting a USB Mass Storage Class
Device
You can connect a USB mass storage class device such
as a USB flash memory device, MP3 player, multimedia
card reader, etc. to the System.
NOTES:
•When connecting with a USB cable, use the USB 2.0 cable
whose length is less than 1 m.
•USB mass storage class device is charged through the
USB MEMORY terminal when the System is turned on and
the source is “USB.”
•You cannot connect a computer to the USB MEMORY
terminal of the System.
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
•Do not disconnect the USB mass storage class device
when the System is turned on. It may cause malfunction
of both this System and the device.
•Noise and static electricity may stop the USB mass
storage class device sound. In this case, disconnect and
connect the USB mass storage class device again after
turning off the System.
Basic Disc/USB Mass Storage Class
Device Operations
To play back the disc/USB mass storage class
device
• Current track number and elapsed
playing time appear.
For MP3/WMA files: Before current
track number and elapsed playing time
appear, the tag information appears if it
is recorded.
• During playback, press again to pause.
To stop playback
• While playback is stopped, total track
number and total playing time (for
MP3/WMA files, group number and track
number) appear.
To select a track
Select the next tracks.
To go back to the beginning of the
current or previous tracks.
To select a group (MP3/WMA only)
Select the next groups.
Select the previous groups.
To forward search/reverse search
Press and hold to fast-forward the track
during playback.
To stop searching, release the button.
Press and hold to fast-reverse the track
during playback.
To stop searching, release the button.
USB cable (not supplied)
EN01-12_UX-G800D[B]3.indd 7EN01-12_UX-G800D[B]3.indd 7 2/21/08 6:34:48 PM2/21/08 6:34:48 PM

8
NOTES:
•If no disc is inserted or no USB mass storage class device is
connected, “NO DISC” or “NO USB” appears on the main
display.
•If MP3/WMA files are not recorded on the disc or in the
USB mass storage class device, “NO PLAY” appears on the
main display.
Playing Repeatedly—Repeat Play
1Press repeatedly to specify the repeat
mode as follows:
REP TRK: Repeats the current (or
specified) track. [ ]
REP GRP: Repeats all tracks in the
current group (MP3/WMA
only). [ ]
REP ALL: Repeats all tracks.
[ ALL]
REP OFF: Normal playback
2or
Programming the Playing Order
—Program Play
1During stops, press until the PRGM
(program) indicator lights up before
playing.
2
or
• For MP3/WMA files: Select a group
number, then a track number.
• For CD: Select a track number.
3Press to program the selected group/
track.
4Repeat steps 2and 3to program other tracks
you want.
• If you try to program a 51st track, “FULL” will
appear.
5The tracks are played back in the
programmed order.
Operations for Program Play (while not playing)
• To check the programmed contents, press 4or
¢.
• To add tracks, repeat steps 2and 3above.
• To erase the last programmed track, press CANCEL.
• To erase the entire program, press and hold CANCEL
for about 2 seconds.
• To exit from program play, press MODE.
– The stored program is kept.
Playing at Random—Random Play
1Press until the RND (random) indicator
lights up before you start playback.
2or
Playback starts in random
order.
Random Play ends when all
tracks are played back.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track,
press 4.
• To exit from random play, press MODE while
playback is stopped.
RESUME Play (For MP3/WMA only)
When you stop the playback by one of the following
operations, this System stores the beginning of the
stopped track on the disc or USB mass storage class
device.
– Pressing 7once
– Changing the source
When you start playback again, playback starts from
the stored position.
To clear the stored position, open the disc tray or
disconnect the USB mass storage class device.
• When you clear the stored position and start
playback, playback starts from the beginning of the
first track.
NOTE:
This function does not work in Program Play and
Random Play.
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the
loaded disc.
• This is possible while the System is on standby.
To cancel the prohibition,
repeat the same procedure.
EN01-12_UX-G800D[B]3.indd 8EN01-12_UX-G800D[B]3.indd 8 2/21/08 6:34:50 PM2/21/08 6:34:50 PM

9
Listening to the Radio
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
Basic Tuner Operations
To select a band
(On the System)
Press repeatedly to select the band:
*Appears only if DAB/FM/AM (TUNER)
button on the System is pressed.
• The selected frequency band
appear.
• When an FM stereo broadcast or a
DAB service with sufficient signal
strength is tuned in, the S (stereo)
or TUNED indicator lights up
respectively.
When you change the source to
DAB for the first time after plugging
in the AC power cord, the System
automatically scans the DAB bands
for available ensembles. (See page
10.)
(On the remote
control)
To change the FM reception mode
(When an FM stereo broadcast is hard to receive)
Press to improve reception.
The M (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press
again.
For FM/AM
To select a frequency
or
Press and hold for more than 2
seconds.
The System starts searching for
stations and stops when a station of
sufficient signal strength is tuned in.
• Press during searching to stop.
• Press repeatedly to change the
frequency step by step.
To tune in to a preset station
or
Press to select its preset number.
• For presetting stations, see the right
column.
For DAB
To select an ensemble
or
Press 4/¢while “ENSEMBLE” is
displayed.
• You can select from the ensembles
found in the ensemble scanning.
To select a service (either primary or secondary)
or
While tuning in to a service, press to
change services.
• When you reach the last/first service
of an ensemble and press ¢/4,
you skip to the next/previous
ensemble respectively. It may take
some time to change ensembles.
• If the System is not tuned in to any
services, pressing ¢/4will start
selecting an ensemble.
To tune in to a preset service
or
Press to select the preset number of
the pre-selected services.
• For presetting services, see below.
To tune in to all ensembles
1“ENSEMBLE” appears on the display.
2
or
Press and hold for more than 2
seconds.
The frequency changes every
second through all ensembles
regardless of the signal status.
• Release the button when the
desired ensemble is reached.
Presetting Stations and Services
You can preset 30 FM stations, 15 AM stations, and 30
DAB services manually.
1Tune in to a station/service you want to preset.
• You can also store the monaural reception
mode for FM stations.
2Press to activate the preset number
entry mode.
• Finish the following steps while
the indication on the display is
flashing.
3
or
Press to select a preset number
for the station/service you want to
store.
EN01-12_UX-G800D[B]f.indd 9EN01-12_UX-G800D[B]f.indd 9 3/5/08 3:42:09 PM3/5/08 3:42:09 PM

10
4Press to store the station/service.
NOTES:
•If you store a new station/service into an occupied preset
number, the previously stored one in that number will be
erased.
•When you preset DAB services, you can only preset
primary services. If you select a secondary service to store,
its primary service is stored instead.
What is DAB System?
DAB (Digital Audio Broadcasting) is one of the digital
radio broadcasting systems available today. It can
deliver digital quality sound without any annoying
interference or signal distortion. Furthermore, it
can carry text, pictures and data. In contrast to FM
broadcast, where each program is transmitted on its
own frequency, DAB combines several programs (called
“services”) to form one “ensemble.” “Primary services”
(main radio stations) are sometimes accompanied by
“secondary services” to broadcast additional programs.
CAUTION:
Electrostatic discharge from your body may cause
noise from the speakers and you cannot hear the
broadcast.
If this happens, turn off the System (on standby), then
turn it on again.
Changing the DAB Information
Each time you press the button, the main
display changes as follows:
PTY: Program Type (See page 11.)
DLS: Dynamic Label Segment (text
messages the station sends)
*The preset number is displayed only when
the service has been selected using the
PRESET UP/DOWN keys.
NOTES:
•If no signals are sent, “NOSIGNAL” (instead of Service
Label), “NO PTY” (instead of PTY) or “NO TEXT” (instead of
DLS) appears on the display.
•If a preset channel which has no signal is selected,
“EMPTY” (instead of Service Label) appears on the display.
Improving the DAB Reception
With the supplied DAB antenna, you may not be able
to receive L-Band ensembles. You can improve the
reception of both L-Band and Band III ensembles by
connecting an active antenna (see page 3).
To supply power to the active antenna
After connecting an active antenna,
press and hold for more than 2 seconds
while the System is on standby. Power is
supplied to the active antenna when DAB
is selected as the source and “ANT.P ON”
appears on the display.
To cut the power supply, press and hold
the button again on standby. Then
“ANT.P OFF” appears on the display.
• You cannot change this setting when
the ECO mode is activated (see page 6).
Scanning Ensembles
With the ensemble scanning function, the System scans
the DAB bands to pick out available ensembles under
your receiving condition.
• When you change the source to DAB for the first
time after plugging in the AC power cord, the System
automatically performs the scanning.
• When you moved your System or adjusted the
antenna position, perform the scanning manually.
To start the scanning
Press and hold for more than 2 seconds
while DAB is selected as the source.
To cancel the scanning, press CANCEL.
If you change to other source during ensemble
scanning, the System will restart the scanning when
DAB is selected as the source again.
• To cancel the scanning and stop restarting the scan,
press CANCEL.
When the scanning is complete, the System starts
playing the first service of the ensemble found first.
EN01-12_UX-G800D[B]f.indd 10EN01-12_UX-G800D[B]f.indd 10 4/2/08 12:30:05 PM4/2/08 12:30:05 PM

11
• For details about PTY codes, see page 17.
1Press to enter the PTY code setting
mode.
“PTY” and “SELECT” appear
alternately.
2
or
Select a PTY code.
3The System searches for 30 preset
FM stations, stops when it finds the
one you have selected, and tunes in
to that station.
• To stop searching any time during search, press
PTY SEARCH.
• To continue searching after it stops on an
unwanted program, press PTY SEARCH again while
the PTY code is flashing on the display.
NOTE:
If no program is found, “NOTFOUND” appears.
Switching Temporarily to a Program
of Your Choice Automatically
The Enhanced Other Networks function allows the
System to switch temporarily to a station/service
broadcasting a program of your choice (TA, NEWS, or
INFO).
• While you are listening to an FM station, the System
can switch to one of the preset FM stations.
• While you are listening to a DAB service, the System
can switch to another DAB service.
• This function works while listening to a station/service
providing the required signals.
Press repeatedly to select the program
type as follows:
TA: Traffic announcement in your
area.
NEWS: News
INFO: Program the purpose of which
is impart advice in the widest
sense.
Receiving FM Stations with Radio
Data System
Radio Data System allows FM stations to send an
additional signal along with their regular program
signals.
With the System, you can receive the following types of
Radio Data System signals.
PS (Program Service):
Shows commonly known station names.
PTY (Program Type):
Shows types of broadcast programs.
RT (Radio Text):
Shows text messages the station sends.
Enhanced Other Networks:
Provides the information about the types of
programs broadcast by the Radio Data System
stations on different networks.
NOTE:
If you want to know more about Radio Data System, visit
<http://www.rds.org.uk>.
Changing the Radio Data System
Information
Each time you press the button, the
information changes as follows:
NOTES:
•“PS,” “PTY,” or “RT” is displayed while the System is
searching for the corresponding Radio Data System
information.
•If no Radio Data System signals are sent by a station,
“NO PS,” “NO PTY,” or “NO RT” appears.
Searching for Programs by PTY Codes
(PTY Search)
While listening to an FM station:
You can locate a particular kind of program from the 30
preset stations (see page 9) by specifying a PTY code.
While listening to a DAB service:
You can locate a particular kind of program from
among all the services you can receive by specifying
the PTY codes.
EN01-12_UX-G800D[B]3.indd 11EN01-12_UX-G800D[B]3.indd 11 2/21/08 6:34:55 PM2/21/08 6:34:55 PM

12
Listening to Digital Audio Player
Front view
1Turn the volume to minimum.
2Press repeatedly to select “AUDIO IN.”
3Start playing the Digital Audio Player connected.
4Adjust the volume.
Digital Audio Player
To audio output (or
headphone out, etc.)
Stereo mini plug cord
(not supplied)
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
To Adjust the Audio Input Level
If the sound from the Digital Audio Player connected
to the AUDIO IN jack is too loud or too quiet, you can
change the audio input level through the AUDIO IN jack
(without changing the volume level).
Press and hold for more than 2 seconds
while “AUDIO IN” is selected as the source.
You can select one of three levels as
follows:
As the number increases, the sound
becomes louder.
How the Enhanced Other Networks function actually works:
Case 1
If no station/service is broadcasting the program of your choice
The System continues tuning in to the current station/service.
\When a station/service starts broadcasting the program of your choice, the System automatically switches to
that station/service. The PTY code indicator starts flashing.
\When the program is over, the System goes back to the previously tuned station/service, but the function still
remains active (the indicator stops flashing and remains lit).
Case 2
If a station/service is broadcasting the program of your choice
The System automatically switches to the station/service. The PTY code indicator starts flashing.
\When the program is over, the System goes back to the previously tuned station/service, but the function still
remains active (the indicator stops flashing and remains lit).
Case 3
If the station/service currently tuned in is broadcasting the program of your choice
The PTY code indicator starts flashing.
\When the program is over, the indicator stops flashing (the function still remains active).
EN01-12_UX-G800D[B]3.indd 12EN01-12_UX-G800D[B]3.indd 12 2/22/08 9:13:10 AM2/22/08 9:13:10 AM

13
Setting the Clock and Using Timers
Setting the Clock
Without setting the built-in clock, you cannot use Daily
Timer and Sleep Timer.
• “0:00” flashes on the main display until you set the
clock.
1Press to activate the clock setting
mode.
• If you have already adjusted
the clock before, press the
button repeatedly until the
clock setting mode is selected.
2
or
Adjust the hour, then the
minute.
• To exit from the clock setting, press CLOCK/TIMER as
required.
• To go back to the previous step, press CANCEL.
The following operations are explained using
the remote control, unless mentioned otherwise.
However, if the System has the same or similar button
names, they can also be used for the operations.
Setting the Sleep Timer
When the System is on, press repeatedly to
specify the time (in minutes) as follows:
The SLEEP indicator lights up.
• To check the remaining time until the System shuts
off, press once.
Turning Off the System
Automatically—AUTO STANDBY
function (only for Disc/USB)
Press and hold until the A.STBY indicator
lights on the display.
• The A.STBY indicator starts flashing after
playback stops.
If no operation is done for about 3
minutes, the System turns off.
• Not applicable for DAB/FM/AM/AUDIO
IN.
To cancel this function, press and hold again.
EN13-20_UX-G800D[B]3.indd 13EN13-20_UX-G800D[B]3.indd 13 2/21/08 6:35:07 PM2/21/08 6:35:07 PM

14
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of the Daily Timers.
1Press repeatedly to select one of the timer setting modes you want to set—DAILY 1 ON
time, DAILY 2 ON time, or DAILY 3 ON time—as follows:
2
or
1Adjust the hour then the minute for on-time.
2Adjust the hour then the minute for off-time.
3Select the playback source—“DAB,” “TUNER-FM,” “TUNER-AM,” “DISC,” “AUDIO IN,” or
“USB.”
4For “DAB/FM/AM”: Select a preset channel.
For “DISC” or “USB”: Select a track. (For MP3/WMA: Select the group, then the track
number.)
For “AUDIO IN”: Make the connected device ready for playback.
5Select the volume.
• You can select the volume level (“VOLUME 0” (VOL MIN) to “VOLUME 40” (VOL MAX)
and “VOLUME – –”). If you select “VOLUME – –,” the volume is set to the last level when
the System is turned off.
3Turn off the System (on standby).
• When the on-time comes, the System sets the volume gradually to the preset level.
• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the previous step.
To Turn Off the Daily Timer
1Press repeatedly to select “DAILY 1,” “DAILY 2,” or “DAILY 3.”
2
To turn on the Daily Timer again, select one of the timer settings by pressing CLOCK/TIMER, then press SET.
EN13-20_UX-G800D[B]f.indd 14EN13-20_UX-G800D[B]f.indd 14 3/18/08 3:08:08 PM3/18/08 3:08:08 PM

15
Troubleshooting
Sounds from USB mass storage class device are
interrupted.
\Noise and static electricity may stop the sound. In
this case, disconnect and connect the USB mass
storage class device again after turning off the
System.
The disc tray does not open or close.
\The AC power cord is not plugged in.
\Disc ejection is prohibited (see page 8).
Radio Operations
Hard to listen to broadcasts because of noise.
\Antennas connections are incorrect or loose.
\The AM loop antenna is too close to the System.
\The FM antenna is not properly extended and
positioned.
\Electrostatic discharge from your body may cause
noise. If this happens, turn off and on the System
again.
Cannot receive an ensemble.
\Your area is not covered by the ensemble.
\The DAB antenna is not properly extended
or positioned. Adjust the antenna and try the
ensemble scanning again.
\Connect an active antenna (not supplied).
Timer Operations
Daily Timer does not work.
\The System has been turned on when the on-time
comes. Timer starts working only when the System
is turned off.
If you are having a problem with your System, check
this list for a possible solution before calling for service.
General
Power does not come on.
\Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled
before you finish.
\There is a time limit. Repeat the procedure again.
Operations are disabled.
\The built-in microprocessor may malfunction due
to external electrical interference. Unplug the AC
power cord and then plug it back in.
Unable to operate the System from the remote
control.
\The path between the remote control and the
remote sensor on the System is blocked.
\The battery is exhausted.
No sound is heard.
\Speaker connections are incorrect or loose.
\Headphones are connected.
The System does not work properly.
\Many functions of this System are implemented
by microcomputers. If the System does not work
correctly, disconnect the AC power cord from the
wall outlet, wait for a while, and connect the cord
again.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\The disc is placed upside down. Place the disc with
the label side up.
\The disc is recorded with the “packet writing (UDF
file system).” It cannot be played. Check the files you
want to play back.
\The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as
you expect.
\Playing order is determined when the groups and
tracks were recorded. It depends on the writing
application.
The disc/USB mass storage class device sound is
discontinuous.
\The disc is scratched or dirty.
\MP3/WMA files have not been properly copied into
the USB mass storage class device.
EN13-20_UX-G800D[B]f.indd 15EN13-20_UX-G800D[B]f.indd 15 4/2/08 9:05:31 AM4/2/08 9:05:31 AM

16
Learning More about This System
• This System can recognize up to 99 groups in a disc.
The total number of groups and tracks (in a disc) that
can be recognized by the System is 512 (for MP3/
WMA).
• This System can recognize up to 99 groups and 9 999
tracks (with a maximum number of 255 tracks in a
group) in a USB mass storage class device.
Listening to the Radio (see pages 9 to 11)
• The time shown on the display is based on the built-
in clock of the System, not on the information sent
through DAB or Radio Data System.
• The Enhanced Other Networks function is available
only when tuning in to FM.
Setting the Clock and Using Timers (see pages 13
and 14)
• You can set the clock and Daily Timer while the Save
Mode is turned on. While setting the clock or Daily
Timer, the display is turning on.
• The clock may gain or lose 1 to 2 minutes per month.
If this happens, readjust the clock.
• When you unplug the AC power cord or if a power
failure occurs, the clock and the timer will be
canceled. You need to set the clock first, then the
timer again.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
Basic and Common Operations (see pages 5 and 6)
• Pressing one of the source buttons also turns on the
System and starts playing back if the source is ready
or connected.
Playing Back a Disc/USB Mass Storage Class Device
(see pages 7 and 8)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably
used for MP3/WMA operations.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time
than regular CDs. (It depends on the complexity of
the group/file configuration.)
– Some MP3/WMA files cannot be played back and
will be skipped. This result from their recording
processes and conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1
or Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
– It is recommended that you make each MP3/WMA
file at a sampling rate of 44.1 kHz and at bit rate of
128 kbps. This System cannot play back files made
at bit rate of less than 64 kbps.
– Playback order of MP3/WMA tracks may be different
from the one you have intended while recording. If
a folder does not include MP3/WMA tracks, they are
ignored.
• Do not use the following USB devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data
security functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device,
also refer to its manual.
– Connect one USB mass storage class device to the
System at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass
storage class device (maximum data transfer rate:
2 Mbps).
– You cannot play back a file larger than 2 Gigabyte.
– This System may not play back some USB mass
storage class devices and does not support DRM
(Digital Rights Management).
EN13-20_UX-G800D[B]3.indd 16EN13-20_UX-G800D[B]3.indd 16 2/21/08 6:35:11 PM2/21/08 6:35:11 PM

17
FINANCE: Stock Market reports, commerce, trading
etc.
CHILDREN: Programs targeted at a young audience.
SOCIAL: Programs about sociology, history,
geography, psychology and society.
RELIGION: Religious programs.
PHONE IN: Involving members of the public
expressing their views either by phone or
at a public forum.
TRAVEL: Travel information.
LEISURE: Programs about recreational activities.
JAZZ: Jazz music.
COUNTRY: Songs which originate from, or continue
the musical tradition of the American
Southern States.
NATION M: Current popular music of the nation or
region in that country’s language.
OLDIES: Music from the so-called “golden age” of
popular music.
FOLK M: Music which has its roots in the musical
culture of a particular nation.
DOCUMENT: Programs concerning factual matters,
presented in an investigative style.
TEST*: Broadcasts for testing emergency
broadcast equipment or unit.
ALARM*: Emergency announcement.
NONE*: No program type, undefined program,
or difficult to categorize into particular
types.
NEWS: News.
AFFAIRS: Topical program expanding or enlarging
upon the news—debate, or analysis.
INFO: Programs the purpose of which is to
impart advice in the widest sense.
SPORT: Programs concerned with any aspect of
sports.
EDUCATE: Educational programs.
DRAMA: All radio plays and serials.
CULTURE: Programs concerning any aspect of
national or regional culture, including
language, theater, etc.
SCIENCE: Programs about natural sciences and
technology.
VARIED: Used for mainly speech-based programs
such as quizzes, panel games and
personality interviews.
POP M: Commercial music of current popular
appeal.
ROCK M: Rock music.
EASY M: Current contemporary music considered
to be “easy-listening”.
LIGHT M: Instrumental music, and vocal or choral
works.
CLASSICS: Performances of major orchestral works,
symphonies, chamber music, etc.
OTHER M: Music not fitting into any of the other
categories.
WEATHER: Weather reports and forecasts.
Description of the PTY codes for Radio Data System and DAB
*Only Radio Data System has this PTY code.
NOTE:
Classification of the PTY codes for some FM stations may be different from the above list.
EN13-20_UX-G800D[B]3.indd 17EN13-20_UX-G800D[B]3.indd 17 2/22/08 9:14:57 AM2/22/08 9:14:57 AM