JWA HARDING 74710 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
74710
ETU
HARDING
ITEM CODE
1500MM
400MM
500MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lig. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucns carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 1 hour For 2 person Addinal tools required
2

PARTS LIST
3
1
2
3
4
5
6
7
8
9
10
10
11 11
12
12
13
13

4
NO. ITEM QTY NO. ITEM QTY
A10PCS
B10PCS
C16PCS
D6PCS
E2PCS
F8PCS
J
8PCS
L
M12PCS
N2PCS
O
4PCS
K
1PC
Φ6*35
Φ15*10
Φ6*30
Φ4*40
Φ3*16
PARTS LIST
Φ4*14
G1PC
H10PCS
I24PCS
2PCS
P4PCS
Φ3*1.5
Φ5*30
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
51 PC
61 PC
71 PC
1 PC
1 PC
2 PCE
2 PCE
2 PCE
2 PCE
2LEFT SIDE PANEL
RIGHT SIDE PANEL
MIDDLE PANEL
10
11
12
13
8
9
Φ3.5*12
Φ6*30
BOTTOM PANEL
SHELF PANEL
BACK PANEL
LEFT DOOR PANEL
RIGHT DOOR PANEL
METAL LEG
METAL LEG
METAL LEG
METAL LEG
Q8PCS

STEP 1:
STEP 2:
5
A X6
1
A
A X4
H X2G X1
A
A
A
A
A
G
H
4
3
A
A
A
A

STEP 3:
STEP 4:
6
6
C X4
C
B X4
4
3
C
C
C
B
B
B
B
C X6B X6
6
3
4
2
1B
B
B
B
C
C
C
C
C
C

STEP 5:
STEP 6:
7
7
C
3
2
1
C X6D X6
7
3
2
5
C
C
D
D
D
D
D
D

STEP 7:
STEP 8:
8
M X8L X1
M X4L X1O X2
11
L
M
M
M
M
M
M
11
12
12
10
10
2
O
1
O
O
OL
M
M
M
M
10
10
11
11
12
12
13
13

STEP 9:
STEP 10:
9
K X8L X1
Q X8
12
12
L
5
2
10
10
Q
Q
Q
Q
Q
Q
Q
K
K
K
K
K
K
K
K
F X8H X8
H
HH
H
H
H
F
F
F
F
F
FF
H
H
F
F
H
F

STEP 11:
STEP 12:
10
J X4I X8P X4N X2
J
8
J
J
J
P
P
PP
N
N
II
II
I
I
I
I
9
I X16
8
9
I
I
I
I
I

STEP 13:
11
E X2
E
E
E
WALL
E
E
E
E
ASSEMBLY IS COMPLETE

12
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
13