JWA WANDSWORTH 68963 User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
WANDSWORTH
ITEM CODE: 68963
Dining Chair

Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible risk to
injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for future reference.
2
PRE-ASSEMBLY PREPARATION
Allow 15 min For 1 person

3

•Prepare a protected surface, either with a blanket or
cardboard.
•Prepare 8x bolt A sets. Thread bolt(A) through spring
washer(C), then washer(D).
•Connect the long apron(2) to the long end of the left
leg(4) and right leg(5), use the dowels(E), in the middle
hole at each corner.
•Connect the short apron(3) to the short end of the left
leg(4) and right leg(5), use the dowels(E), in the middle
hole at each corner.
•Secure the connections with 2x bolt A sets per corner,
fasten with allen key(G)
•Tighten only until the bolt is a little firm in the thread, do
not fasten completely.
4
STEP 1:

•Prepare 2 bolt B sets, by threading bolt(B) through spring
washer(C), then washer(D).
•Attached the base to the seat(1) as shown below.
•Secure on the connecting points on the left and right legs
with bolt set B.
•Fasten firmly with Allen Key(G).
5
STEP 2:
•Attach the 4x non-slip discs(F) as shown above, on the
bottom of each leg.
STEP 3:

•Stand the chair the right way up on a level surface. Push
down on the chair until it levels out. Do not lean beyond
your own balance.
•Once level, flip the chair back over again (upside down).
Now go around in a clockwise direction and fully fasten
all the bolts. Do not over tighten, this may damage the
product.
6
STEP 4:
ASSEMBLY IS COMPLETE

7
PRODUCT CARE:
REGULAR CARE:
•Protect from direct sunlight
•Vacuum regularly using low suction
•Rotate reversible cushions regularly
•Avoid exposure to new clothing, cushions or throws as this may lead to
dye transfer and permanent staining
CLEANING:
•Do not remove cushion covers for separate cleaning even though they
may have zippers
•Do not wash, Do not dry clean, Do not shampoo clean
•Clean only with hot water extraction machine. Professional cleaning
recommended
•Do not use dishwashing liquid or laundry detergent. Use only upholstery
detergents
•Do not wet filling
•Dry in shade away from direct heat and sunlight
•Allow to dry thoroughly before re-use
SPOT CLEANING:
•Do not rub
•Do not spot clean with any solvent
•Treat spills and stains as soon as possible
•Gently scrape off any soil or blot any liquid from the surface of the fabric
before applying cleaner
•Apply proprietary cleaning agents strictly according to instructions to
remove the residue of the spill
•Do not saturate the fabric or interior with water or other cleaning liquids
WARNING:
Apply only water-based soil resist (fabric protection) treatments. Do not use aerosol products
* PILLING IS NOT A FABRIC DEFECT OR FAULT AND IS NOT COVERED BY WARRANTY
* PILLING IS A NORMAL OCCURRENCE CAUSED BY WEAR AND TEAR AND DOES NOT AFFECT THE
DURABILITY OR FUNCTIONALITY OF THE FABRIC AND IS EASILY REMOVED