JWA ELDA User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
ELDA
ITEM CODE 68440
DESK

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2
Allow 45 min For 2 person Additional tools required

3
PARTS LIST
1Desktop panel
2Layer panel
P1 Left main frame
P2 Right main frame
P3 Right back main frame
P4 Connection pipe
P5 Panel support frame
P6 Back support pipe

Install fitting G at the bottom of metal frame P1, P2 and P3.
4
STEP 1:
Use fitting B to fix panel 2 on the metal frame of P2 and P3.
Fix the metal pipe P4 on the metal frame P2 and P3 with
fitting A2.
STEP 2:

Use fitting B to fix panel 2 on the metal frame of P2 and P3;
Fix the metal pipe P4 on the metal frame P2 and P3 with fitting
A2.
STEP 3:
1) Use parts A1, A2, F and E to fix the metal frame P5 on the
metal frame P2 and P3;
2) Fix metal frame P1 on metal frame P5 with fitting A2.
STEP4:
5

1) Connect the metal pipes P6 with fitting C and D;
2) Fix the metal pipe P6 on the metal frame P1 and P3 with
the fitting A3.
STEP 5:
Fix panel 1 with fitting A2 through metal frame P5.
STEP 6:
6

Fix the metal pipe P4 on the metal frame P2 and P3 with fitting
A2.
STEP 7:
1) fix the metal pipe P4 on the metal frame P2 and P3 with
fitting A2;
2) fix panel 2 on the metal frame P2 and P3 with fitting B.
3)Lock P3 with part B, then lock the anti-fall device to the
wall.
STEP 8:
7

8
ASSEMBLY IS COMPLETE

9
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.

10
To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void