JWA FULTON 68047 User manual

INSERT PAGE NUMBER
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
FULTON
68047
Queen Bed

Allow 45 min For 2 person Additional tools required
1
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for future reference.

A
M8X19
X8 B
M5X100
X1
CM12 X1 M12
X4
E
M4X30
X6 F
M8X40
X4
G
M8X30
X4
No.
Item
QTY
No.
Item
QTY
1
Headboard
12
Left
Side Rail 1
3
Right
Side
Rail
14
Foot
Rail 1
5
Center
rail 16
Support
legs2
7
Slat
s18Feet 4
PARTS LIST
D
2

•Prepare a floor or bench with a blanket or cardboard.
•Stand the Headboard(1) upside down, have another
person hold it.
•Screw in the 2 x FEET(8), as shown below.
•Stand the Headboard(1) with the feet on the ground and
lean against a wall for the time being.
STEP1:
STEP2:
•Repeat Step 1 but this time do the Foot Rail(4). As
shown below.
3

•Unscrew the bolts in the Headboard(1) and Foot Rail(4),
so they are half way out.
•Have a 2nd person hold the headboard.
•Attach the Left Side Rails (2) to the Headboard(1), by
clipping the bracket onto the bolts. Place the tongs of the
brackets in-between the washer and headboard.
•Now, attach Left Side Rails (2) to the Foot Rail(4). ), by
clipping the bracket onto the bolts. Place the tongs of the
brackets in-between the washer and headboard.
STEP3:
STEP4:
•Repeat Step 3, but this time do the Right Side Rail(3).
4

•Attach the Centre Rail(5) to the Headboard(1) and Foot
Rail(4), as shown below.
•Use 4x Bolts(G) paired with Washer(A). Fasten with Allen
Key(B).
STEP5:
STEP6:
•Now go around and fully tighten all the bolts from steps
3&4 with Allen Key(B). Do not over tighten the bolts as
this may damage the bed.
5

•Attach the 2 x support legs(6) to the Centre Rail(5). As
shown below.
•Thread Bolt(F) Through Washer(A). Then push the bolt
through the holes on the Centre Rail and Support Leg.
Screw on Nut(D) on the bottom onto Bolt(F). Tighten
bolt(F) with Allen Key(B), whilst holding nut(D) in-place
with Wrench(C).
STEP7:
6

•Place the slats(5) into the bed, as shown below.
•Secure the ends of the slats to the side rails with screw
(E) and a Philips head screw driver.
STEP8:
ASSEMBLY IS COMPLETE
7

REGULAR CARE:
•Protect from directsunlight
•Vacuum regularly using low suction
•Rotate reversible cushionsregularly
CLEANING:
•Do not remove cushion covers for separate cleaning even though they
may have zippers
•Do not wash, Do not dry clean, Do not shampoo clean
•Clean with hot water extraction machine. Professionalcleaning
recommended
•Do not use dishwashing liquid or laundrydetergent
•Use only upholstery detergents
•Do not wet filling
•Dry in shade away from direct heat andsunlight
•Allow to dry thoroughly beforere-use
SPOT CLEANING:
•Do not rub
•Do not spot clean with anysolvent
•Treat spills and stains as soon aspossible
•Gently scrape off any soil or mop any liquid from the surface of the fabric
•Apply proprietary cleaning agents strictly according to instructions to
remove the residue of thespill
•Do not saturate the fabric or interior with water or other cleaning liquids
WARNING:
Apply only water-based soil resist (fabric protection) treatments. Do not
use aerosol products
* PILLING IS NOTA FABRIC DEFECT OR FAULTAND IS NOT
COVERED BY WARRANTY
* PILLING IS A NORMAL OCCURRENCE CAUSED BY WEAR AND TEAR AND DOES
NOT AFFECT THE DURABILITY OR FUNCTIONALITY OF THE FABRIC AND IS EASILY
REMOVED
8