Küppersbusch EEB 9800.0 User manual

Installation instructions
Important - Save for the local electrical inspector’s use.
EEB 9800.0
EEB 9600.0
072444 IC1

2Installation instructions EEB 9600.0
For your information...
Be sure to read the information in this manual carefully before you install the
oven.
Please keep this manual in a safe place and pass it on to future owners for
their information and safety.
The following symbols are used in this operating manual:
=The warning triangle will alert you about possible health risks or things
that can cause potential damage to your appliance.
FYou’ll find useful hints and information when you see this symbol.
Warranty
This warranty is extended to the original purchaser and succeeding owners for
products purchased for ordinary home use. It does not cover its use in com-
mercial situation. Should the appliance be sold by the original purchaser during
the warranty period, the new owner continued to be protected until the expi-
ration date of the original purchaser’s warranty period. Save your dated receipt
or other evidence of the installation/occupancy date. Proof of original purchase
date is needed to obtain service under warranty. The warranty applies even if
the owner should move during the warranty period.
Küppersbusch does not assume any responsibility for consequential or inci-
dental damages. This warranty provides you with certain legal rights. You may
also have other rights which may vary from state to state.
What Is Covered
For one full year from the date of the original purchase, we will provide parts,
service and labor in your home to repair or replace any part of the cook top
that fails because of a defect in materials or workmanship. This service is pro-
vided free of charge. All warranty service will be provided by an authorized
technician during normal business hours.
What Isn’t Covered
■ Service by an unauthorized agency will not be reimbursed. Likewise, the
warranty doesn’t cover any damage or repairs due to service performed by
an unauthorized agency, or by the use of unauthorized parts.
■ Service visits to teach you how to use the appliance.
■ Service visits to correct the installation. You are responsible for providing
electrical wiring and other connecting facilities.
■ Reset circuit breakers or replace home fuses.
■ Damage resulting from accident, alteration, misuse, improper installation,
abuse or installation not in accordance with local electrical codes, or im-
proper storage of the appliance.
■ Repairs due to other than normal household use.
Disposing of the packaging and
the old appliance
Be sure to dispose of the transport packaging properly. Disposal should not
have a negative impact on the environment. Recycling the packaging saves
raw materials and reduces the amount of waste.
Be sure to dispose of your old appliance properly, as well. Even if it can no
longer be used, it still contains useful materials. Before discarding an old ap-
pliance, disconnect the power cord and remove the door to prevent it from
becoming a hazard.
Contents
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation in a high cupboard. . . . . . . . . . . . . . . . . . . . . . . 3
Installation under a countertop . . . . . . . . . . . . . . . . . . . . . . 3
Options for mounting under a countertop
Installation under the Cook-Center KC 906.2 E . . . . . . . . . . . . 4
Electrical supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation in kitchen furniture . . . . . . . . . . . . . . . . . . . . . . 5
For technical information and/or
replacement parts, please contact the
Küppersbusch Customer Care line
at
1-800-459-0844
For the most efficient assistance,
please have the Model and Serial
numbers for the appliance available.

Installation instructions EEB 9600.0 3
General
=Turn off the power source before installing the oven.
=WARNING! In case the oven is not installed and secured in accordance
with these installation instructions, there is a risk of tipover! Check after
installation that the fastening screws are securely tightened and that the
appliance cannot be moved.
=Only qualified personnel should perform installations and repairs on elec-
trical appliances. Do not repair or replace any part of the appliance unless
specifically recommended in this manual. Do not put your safety at risk.
=Only KÜPPERSBUSCH built-in cooktops have been designed and tested
for installation above a KÜPPERBUSCH built-in oven. No other cooktops
may be used above the oven.
Installation conditions
The oven must be placed on a board that can withstand 72.5 kg/160 pounds
or more. The oven should fit snugly against the side walls and the frame
should overlap them.
WARNING! The cabinet or adjacent side walls must be secured so the installed
oven can’t tilt.
Make sure there's an opening in the rear section, in order to provide sufficient
air for cooling the oven. If there isn't an opening, cut a hole with at least
300 cm2/45 in2depth in one of the adjacent surfaces, preferably in the bot-
tom board or top cover.
Make sure all components surrounding the oven can resist temperatures of at
least 100 °C/210 °F. These includes varnishes, edge bands, plastic surfaces,
adhesives and paints. The adjacent cabinet fronts should be able to resist tem-
perature up to 70 °C/160 °F.
To eliminate the risk of burns or fire by reaching over heated surface units,
cabinet storage space located above the surface units should be avoided. If
cabinet storage is to be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5 inches beyond the bottom of
the cabinets.
Installation in a high cupboard
The frame of the oven should overlap the boundary at the bottom and on both sides.
Installation under a countertop
The frame of the oven overlaps the niche boundary at the bottom and on both sides.

4Installation instructions EEB 9600.0
Options for mounting under a countertop
Option 1: in a cupboard on a board.
Option 2: between two cupboards on a se-
cured board.
Boards (approximately 19 mm/ 3/4" thick)
must be attached to the adjacent cabinets
on the right and left, so the oven can be
clipped in at the sides.
The following KÜPPERSBUSCH built-in cooktops may be installed above the
oven:
F* The gap between the countertop and the front panel is not necessary
for the models EGS 304.2 and EKS 304.1.
We recommend you to place the gap directly below the countertop, be-
cause it’s not so visible if it is between the oven an the front panel.
FLook for the recess size and installation specifics for the cooktop in the
installation instructions for the cooktop.
Installation under the
Cook-Center KC 906.2 E
The oven must be positioned between
two cabinets on a secured shelf. Shel-
ves (approximately 19mm/
9/16" thick) must be attached to the
adjacent cabinets on both sides so the
oven can be clipped in at the sides.
Please review the installation instruc-
tions for the model KC 906.2 for the
position of the Cook-Center.
Be sure to install a stain-
less steel filler panel (acc.
No. 454) between the
Cook-Center and the oven.
The stainless steel filler
panel is required and sold
separately.
Model: „A“ „B“ „C“
EKE 854.1
EKE 854.2
EKE 804.2
EKE 604.2
30-50 mm
1-1/8 to 2"
103 mm 4-1/16" ≥103 mm ≥4-1/16"
EGS 304.0* 97 mm 3-13/16" ≥97 mm ≥3-13/16"
EKS 304.1* 85 mm 3-3/8" ≥85 mm ≥3-3/8"
EKS 604.2
EKS 804.2 103 mm 4-1/16" ≥103 mm ≥4-1/16"

Installation instructions EEB 9600.0 5
Electrical supply
=The installation or laying of a conduit box or the replacement of the con-
nection cable may only be performed by a qualified electrician in com-
pliance with all regulations.
Conduit box
Do not install the conduit box in the installation area or above the countertop.
Attach it to the side, underneath on the wall or in a high cabinet under the
installation surface.
Provide a hole in the wall or bottom so a cable can go to the conduit box.
Electrical supply
The power supply should be a 120/240 volts system, 3-wire with ground.
Electrical diagram
for a 120 / 240 volts system,
3-wire with ground:
Install a suitable conduit box (not furnished) to connect the oven.
Don’t shorten the conduit. The conduit should be routed to allow the removal
of the oven.
Installation, electrical connections and grounding must comply with all stan-
dards.
■ The conduit-box must be protected by a circuit breaker or fuse, having
amperage as noted in this chapter.
Connected load 240 V, 60 Hz, 3.6 kW, fuse current: 15 A
– Connect the cable to the conduit box.
Installation in kitchen furniture
Screw the provided clips to both sides of the appliance, using the holding pla-
tes mounted in the cabinet. The holding plates are supplied, as well. Install
them on both inside cabinet sides before installing the appliance. See illustra-
tions below.
– Place the holding plate at a distance
of 280 mm/11“ from the bottom cup-
board edge with the raised elements
towards the cupboard and mark and
drill the rear holes (1).
– Move the holding plate so that the
front holes lie over the drill holes.
– Attach the holding plate to the cup-
board with the screws enclosed.
– Screw the clips firmly to the side
walls.
– Insert the appliance into
the cabinet space until it
fits. Don't pinch the
appliance connection
cable in the process!
The connection cable
shouldn't touch the
back of the appliance.

KÜPPERSBUSCH USA
4920 W. Cypress Street, Suite 106
Tampa, Florida 33607
Telephone: [phone] Fax: [phone]
Customer Care line: 1 - 800 - 459 - 0844
www.kuppersbuschusa.com
KÜPPERSBUSCH USA is a division of Teka USA