Kärcher K 2.01 User manual

English
K 2.01
Please keep the original box, packaging and receipt. Before operating this
unit, please read this manual thoroughly and retain it for future reference.
5.961-519.0 (01/07)

2 English
Overview 3
Important Safety Instructions 4-5
Assembly Instructions 6
Operating Instructions 7
Using the Accessories 8
Working with Detergents 9
Shut Down 10
Taking a Break 10
Winterizing and Long-Term Storage11
Care and Maintenance Instructions 11
Cleaning Tips 12-13
Optional Cleaning Accessories 13
Troubleshooting 14 -15
For household use only !
Call: 1-800-537-4129 for help or visit
our website:
www.karcher-canada.com
The owner and/or user must have an
understanding of the manufacturer’s
operating instructions and warnings be-
fore using this pressure washer.
Warning information should be empha-
sized and understood.
If the operator is not fluent in English,
the manufacturer’s instructions and
warnings shall be read to and discussed
with the operator in the operator’s native
language by the purchaser/owner, mak-
ing sure that the operator comprehends
its contents.
Owner and/or user must study and
maintain for future reference the manu-
facturers’ instructions.
DANGER
indicates “an imminently hazardous sit-
uation which, if not avoided, will result in
death or serious injury.”
WARNING
indicates “a potentially hazardous situa-
tion which, if not avoided, could result in
death or injury.”
CAUTION
indicates “a potentially hazardous situa-
tion which, if not avoided, may result in
minor or moderate injury or in property
damage incidents.”
HIGH PRESSURE WASHER OPERATOR MANUAL
Specifications
Max. Pressure 1400 PSI
Water volume 1.3 GPM
Amp draw 13 AMPS
Voltage 120 V
Part No. 1.672-370.0
Serial no.
Kärcher Customer Service CDN
Owner/User Responsibility
Safety Alert Symbols

English 3
Item Description:
1 ON/OFF switch
2 Connector for detergent suction tube
3 High pressure outlet
4 Water inlet with
garden hose connector
5 Detergent suction tube with filter
6 Vario power spray wand
7 Trigger gun
8 Trigger gun safety lock
9 High pressure hose
10 Power cord
MODEL OVERVIEW

4 English
WARNING!
When using this product basic
precautions should always be fol-
lowed, including the following:
Read all the instructions before us-
ing the product.
To reduce the risk of injury, close su-
pervision is neccessary when a
product is used near children.
Know how to stop the product and
bleed pressures quickly. Be thor-
oughly familiar with the controls.
 Stay alert — watch what you are doing.
Do not operate the product when fa-
tigued or under the influence of alco-
hol or drugs.
Keep operating area clear of all per-
sons.
Do not overreach or stand on unsta-
ble support. Keep good footing and
balance at all times.
Follow the maintenance instructions
specified in the manual.
Risk of Injection or Injury to persons
- Do not direct discharge stream at
persons.
 High pressure jets can be dangerous if
subject to misuse. The jet must not be
directed at persons, animals, electrical
devices, or the machine itself.
Wear safety goggles.
Do not use acids and solvents in this
product. These products can cause
physical injuries to the operator and
irreversible damage to the machine.
To reduce the risk of electrocution,
keep all connections dry and off the
ground.
Do not touch plug with wet hands.
The Trigger Gun Safety Lock PRE-
VENTS the trigger from accidentally
being engaged. This safety feature
DOES NOT lock trigger in the ON
position.
WARNING
DO NOT SPRAY ELECTRICAL AP-
PARATUS AND WIRING.
DO NOT USE WITH FLAMMABLE
LIQUIDS AND TOXIC CHEMICALS.
HIGH PRESSURE. KEEP CLEAR
OF NOZZLE.
INJECTION HAZARD: EQUIP-
MENT CAN CAUSE SERIOUS IN-
JURY IF THE SPRAY
PENETRATES THE SKIN. DO NOT
POINT THE GUN AT ANYONE OR
ANY PART OF THE BODY. IN
CASE OF PENETRATION SEEK
MEDICAL AID IMMEDIATELY.
THIS SYSTEM IS CAPABLE OF
PRODUCING 1400 PSI TO AVOID
RUPTURE AND INJURY, DO NOT
OPERATE THIS PUMP WITH COM-
PONENTS RATED LESS THAN
1400 PSI WORKING PRESSURE
(INCLUDING BUT NOT LIMITED
TO SPRAY GUNS, HOSE AND
HOSE CONNECTIONS).
BEFORE SERVICING, CLEANING
OR REMOVING ANY PARTS,
SHUT OFF POWER AND RELIEVE
PRESSURE.
IF CONNECTION IS MADE TO A
POTABLE WATER SYSTEM, THE
SYSTEM SHALL BE PROTECTED
AGAINST BACKFLOW.
SAVE THESE
INSTRUCTIONS !
IMPORTANT SAFETY INSTRUCTIONS

English 5
Use only 3-wire extention cords that
have 3-prong grounding-type plugs
and 3-pole cord connectors that ac-
cept the plug from the product.
Up to 25 ft = 12/3 AWG; 25 to 50 ft =
10/3 AWG.
Use only extension cords that are in-
tended for outdoor use. These ex-
tension cords are identified by the
marking “Acceptable for use with
outdoor appliances; store indoors
while not in use.”
Use only extension cords having an
electrical rating not less than the rat-
ing of the product.
Do not use damaged extension
cords.Examine extension cord be-
fore using and replace if damaged.
Do not abuse extension cord and do
not yank on any cord to disconnect.
Keep cord away from heat and sharp
edges.
Always disconnect the extension
cord from the receptacle before dis-
connecting the product from the ex-
tension cord.
If you are using an extension cord, it
should always be completely un-
wound from the cable drum.
WARNING
To reduce the risc of electrocution, keep
all connections dry and off the ground.
Do not touch plug with wet hands.
CAUTION
When connecting the water inlet to the
water supply mains, local regulations of
your water company must be observed.
In some areas the unit must not be con-
nected directly to the public drinking wa-
ter supply. This is to ensure that there is
no feedback of chemicals into the water
supply. Direct connection via a receiver
tank or backflow preventer, for example,
is permitted.
Dirt in the feed water will damage the
unit. To avoid this risk, we recommend
fitting a water filter.
Garden hose must be at least 1/2
inch or 5/8 inch in diameter.
Flow rate of water supply must not
fall below 2 GPM (gallons per
minute).
Flow rate can be determined by run-
ning the water for one minute into an
empty 5-gallon container.
The water supply temperature must
not exceed 104°F/40°C.
Never use the pressure washer to
draw in water contaminated with sol-
vents, e.g. paint thinners, gasoline,
oil, etc.
Always prevent debris from being
drawn into the unit by using a clean
water source.
Extension Cords WATER SUPPLY
(Cold Water Only)

6 English
Attach the high pressure hose to the
trigger gun.
ÎSTEP 1:
Pull out the locking slide from the
right side of the trigger gun handle.
ÎSTEP 2:
Insert the small end of the high pres-
sure hose into place.
ÎSTEP 3:
Push the locking slide back into the
trigger gun to lock the hose in posi-
tion.
ÎSTEP 4:
Connect the detergent suction tube
to the pressure washer.
ASSEMBLY INSTRUCTIONS

English 7
ÎSTEP 1:
Connect the high pressure hose to
the unit’s high pressure outlet.
ÎSTEP 2:
Insert the spray wand into the trigger
gun. Carefully press in against the
spring tension and twist into the
locked position.
ÎSTEP 3:
Connect garden hose to unit’s water
inlet.
ÎSTEP 4:
Connect garden hose to the cold wa-
ter source and turn water on com-
pletely. Plug the power cord into the
power outlet.
ÎSTEP 5:
Unlock the trigger gun safety lock.
Trigger the gun to eliminate trapped
air, wait for a steady flow of water to
emerge from the spray nozzle.
ÎSTEP 6:
Turn on the high pressure washer (I/
ON).
The motor starts only if the trigger
of the gun is pulled and shuts off
when the trigger is released.
OPERATING INSTRUCTIONS

8 English
WARNING
To avoid serious injury never point
spray nozzle at yourself, other per-
sons or animals.
The Vario Power Spray Wand allows
you to adjust the cleaning pressure.
To clean at maximum pressure, the
wand must be positioned to the high
pressure setting (Max).
For reduced pressure turn the wand
collar in the „Min“ direction.
To apply detergent, the wand
must be positioned to the low
pressure setting (Mix).
CAUTION
This unit has been designed for use with
cleaning detergents recommended by
the manufacturer. The use of other
cleaning detergents may affect the op-
eration of the machine and void the war-
ranty.
USING THE ACCESSORIES
Vario Power Spray Wand

English 9
Detergents can only be applied at
low pressure setting (Mix).
ÎSTEP 1:
Install the Vario Power Spray Wand.
Set the spray wand to the low pres-
sure setting (Mix).
ÎSTEP 2:
Fill a container with Kärcher deter-
gent. Place the filter end of detergent
suction tube into the container.
ÎSTEP 3:
Turn on the pressure washer (I). Pull
trigger to operate unit: Liquid deter-
gent is drawn into the unit and mixed
with water. Apply detergent to work
area. Do not allow detergent to dry
on surface.
ÎSTEP 4:
Cleaning up: Always draw fresh wa-
ter through the detergent tank or si-
phon tube when done to flush any
remaining detergents from the injec-
tion system.
For best results see Cleaning Tips on
pages 12 & 13 for specific informa-
tion on how to clean different surfac-
es.
Always Use Kärcher Detergent for
Best Results
Kärcher biodegradable detergents are
specially formulated to protect the envi-
ronment and your pressure washer.
Special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a long-
er life. For Kärcher Detergents, check
your retailer or call our service center for
help.
The following Kärcher detergents are
available:
Pressure wash
Deck + Fence wash
Degreaser
Vehicle wash
CAUTION
Never use:
– Bleach, Chlorine products and other
corrosive chemicals
– Liquids containing solvents (i.e.,
paint thinners, gasoline, oils)
– Tri-sodium phosphate products
– Ammonia products
– Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
WORKING WITH DETERGENTS

10 English
STEP 1: Release trigger (A) and en-
gage gun safety lock (B).
STEP 2: Turn pressure washer to
(0/OFF) position.
STEP 1: Turn the switch to 0/OFF posi-
tion and unplug cord from outlet.
STEP 2: Turn off the water source.
STEP 3: Press trigger to release water
pressure.
STEP 4: Disconnect the garden hose
from the water inlet on the unit..
STEP 5: Disconnect the high pressure
hose from the high pressure outlet.
STEP 6: Release trigger (A) and en-
gage gun safety lock (B).
TAKING A BREAK ..five minutes or more
SHUTTING DOWN
23
B
A

English 11
Î1: Disconnect all water connections.
Î2: Turn on the machine for a few
seconds, until the water which had
remained in the pump exits, turn off
immediately.
Î3: Do not allow high pressure hose
to become kinked.
Î4: Store the machine and accesso-
ries in a room which does not reach
freezing temperatures. DO NOT
store near furnace or other sources
of heat as it may dry out the pump
seals.
CAUTION
Failure to follow the above directions
will result in damage to the pump as-
sembly and accessories.
Pull out the water inlet filter with flat-
nose pliers and rinse out in warm water.
Pull it out and rinse out in warm water.
The appliance is maintenance-free.
WINTERIZING AND LONG-TERM STORAGE
CARE AND MAINTENANCE INSTRUCTIONS
Cleaning the water inlet filter
Cleaning the detergent inlet filter
Maintenance

12 English
(with or without detergent). Pre-rinse
deck and surrounding area with fresh
water. If using Kärcher Deck Wash, ap-
ply to surface at low pressure. For best
results, limit your work area to smaller
sections of approximately 25 square
feet. Allow Deck Wash to remain on sur-
face 1-3 minutes. Do not allow deter-
gent to dry on surface. Rinse at high
pressure in a long sweeping motion
keeping the spray nozzle approximately
3-6 inches from the cleaning surface.
Always clean from top to bottom and
from left to right. When moving on to a
new section of the cleaning surface, be
sure to overlap the previous section to
eliminate stop marks and ensure a more
even cleaning result.
CAUTION
Do not use rotating jet on wood surfaces
as it may cause damage.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing Kärcher Pressure Wash, apply to
surface at low pressure (for best results,
limit your work area to sections of ap-
proximately 6 feet and always apply de-
tergent from bottom to top). Allow
Pressure Wash to remain on surface 1-
3 minutes. Do not allow detergent to dry
on surface, if surface appears to be dry-
ing, simply wet down surface with fresh
water. If needed, use special wash
brush attachment to remove stubborn
dirt. Rinse at high pressure from top to
bottom in an even sweeping motion
keeping the spray nozzle approximately
6 inches from the cleaning surface.
CAUTION
Do not use rotating jet on siding as it
may cause damage.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing Kärcher Pressure Wash or Degreas-
er, apply to surface at low pressure. For
best results, limit your work area to
smaller sections of approximately 25
square feet. Allow Pressure Wash or
Degreaser to remain on surface 1-3
minutes. Do not allow detergent to dry
on surface. Rinse at high pressure in a
sweeping motion keeping the spray
nozzle approximately 3-6 inches from
the cleaning surface. Always clean from
top to bottom and from left to right. For
removing extremely stubborn stains,
use the rotating jet.
(with or without detergent). Pre-rinse
vehicle with fresh water. If using Kärcher
Vehicle Wash, apply to surface at low
pressure. For best results, clean one
side of vehicle at a time and always apply
detergent from bottom to top, do not al-
low detergent to dry on surface. If need-
ed, use special wash brush attachment
to remove stubborn dirt. Rinse at high
pressure in a sweeping motion keeping
the spray nozzle approximately 6-8 inch-
es from the cleaning surface (distance
should increase when rinsing pin-striping
or other sensitive surfaces). Always
clean from top to bottom and from left to
right. For best results, wipe surface dry
with a chamois or soft dry cloth.
CAUTION
Do not use rotating jet on vehicles as it
may cause damage.
CLEANING TIPS
Deck Cleaning
House Siding
Cement Patios, Brick and Stone
Cars, Boats & Motorcycles

English 13
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing Kärcher Pressure Wash or Degreas-
er, apply detergent at low pressure.
Allow Pressure Wash to remain on sur-
face 1-3 minutes.Do not allow detergent
to dry on surface. Rinse at high pres-
sure keeping the spray nozzle approxi-
mately 3-6 inches from the cleaning
surface. For removing extremely stub-
born dirt, it may be necessary to move
the spray nozzle even closer to the sur-
face for greater dirt cutting action.
CAUTION
Do not use rotating jet on cloth, plastic
or other sensitive surfaces as it may
cause damage.
(with or without detergent). Pre-rinse
furniture and surrounding area with
fresh water. If using Pressure Wash, ap-
ply to surface at low pressure. Allow
Pressure Wash to remain on surface 1-
3 minutes. Do not allow detergent to dry
on surface. If needed use special Wash
Brush Attachment to remove stubborn
dirt. Rinse at high pressure in a sweep-
ing motion keeping the spray nozzle ap-
proximately 3-6 inches from the
cleaning surface. For best results, clean
from top to bottom and from left to right.
CAUTION
Do not use rotating jet on patio or lawn
furniture as it may cause damage.
Before cleaning any surface an in-
conspicuous area should be cleaned
to test spray pattern and distance for
maximum cleaning results.
If painted surfaces are peeling or
chipping, use extreme caution as
pressure washer may remove the
loose paint from the surface.
When using on surfaces which might
come in contact with food, flush sur-
faces with plenty of drinking water.
For additional cleaning tips, visit our
website.
Optional cleaning accessories are avail-
able to further enhance your cleaning
capabilities: For details call
1-800-537-4129 or visit
www.karcher-canada.com.
Rotating Wash Brush
Wash Brush
Underbody Wand
Pipe Drain Cleaner
Sandblasting Attachment
Extension Wand
Water Siphon Kit
25 Ft. Extension Hose
T-Racer
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
Patio & Lawn Furniture
Recommendations
OPTIONAL CLEANING ACCESSORIES

14 English
CAUTION Disconnect the machine from the power
source before making any repair.
TROUBLESHOOTING
Symptom Cause Solution
Motor will not start On/Off switch is in the “OFF”
(O) position.
Turn switch to the “ON” (I)
position
Power cord is not plugged in. Plug in power cord.
Extension cord is too long. Replace extension cord with
either a 25 ft. 12/3 gauge cord
or a 50 ft. 10/3 gauge cord.
Extension cord is not proper
gauge.
Extension cord is damaged.
Electrical outlet does not supply
adequate power.
Try a different outlet.
Unit does not reach
high pressure.
Diameter of garden hose is too
small.
Replace with a 1/2 inch or 5/8
inch garden hose.
Water supply is restricted. Check garden hose for kinks,
leaks and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged. Remove filter and rinse out in
warm water.
Spray wand is in low pressure
position.
Turn spray wand to high
pressure position.
Output pressure
varies high and low.
Not enough inlet water supply. Turn water on full force. Check
garden hose for kinks, leaks or
blockage.
Pump is sucking air. Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow of
water emerges through the
nozzle.
Water inlet filter is clogged. Remove filter and rinse out in
warm water.
Discharge nozzle is obstructed. Blow out or remove debris with
a fine needle.
Calcified gun, hose or spray
wand.
Run distilled vinegar through
detergent suction tube.

English 15
If you encounter any additional difficul-
ties not listed, please call for help or visit
our website. Call: 1-800-537-4129 for help
or visit our website:
www.karcher-canada.com
No detergent. Detergent suction tube not
properly connected to the
machine.
Check connection.
Detergent is too thick. Dilute detergent, for best
results use Kärcher detergent.
Filter on detergent suction tube
is clogged.
Run warm water through filter
to remove debris.
Damaged or clogged detergent
suction tube.
Remove obstruction or replace
detergent suction tube.
Spray wand is in high pressure
position.
Turn spray wand tip to low
pressure position.
Discharge nozzle is obstructed. Blow out or remove debris with
fine needle.
Garden hose
connection leaks.
Loose fittings. Tighten fittings.
Missing/worn rubber washer. Insert new washer.
Spray wand leaks. Spray wand not properly
attached.
Insert the spray wand into the
trigger gun. Carefully press in
against the spring tension and
twist into the locked position.
Broken o-ring or plastic insert. Call service center.
Pump is noisy. Pump is sucking air. Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow of
water emerges through the
nozzle.
Water leaks from
pump (up to 10 drops
per minute is permis-
sible).
Loose fittings. Check that all fittings are tight.
Water seals are damaged or
worn.
Call service center.
Oil Drip. Oil seals are damaged or worn. Call service center.
Symptom Cause Solution
Kärcher Customer Service CDN

16 English
Notes

Français
Veuillez conserver la boîte originale, l’emballage et le reçu.
Avant d’utiliser cet appareil pour la première fois, veuillez lire la présente
notice et vous conformer aux instructions qu’elle contient.
K 2.01
5.961-519.0 (01/07)

2 Français
Généralités 3
Importantes consignes de sécurité 4-5
Instructions de montage 6
Mode d'emploi 7
Utilisation des accessoires 8
Emploi de détergents 9
Arrêt de l'appareil 10
Pause 10
Remisage hivernal et entreposage à
long terme 11
Instructions d'entretien et de
maintenance 11
Conseils de nettoyage 12-13
Accessoires de nettoyage en option13
Dépannage 14-15
A usage domestique seulement !
Appeler : 1-800-537-4129 pour obtenir
de l'aide ou visiter notre site Web :
www.karcher-canada.com
Avant d'utiliser ce nettoyeur pression, le
propriétaire et/ou l'utilisateur doit impé-
rativement avoir pris connaissance des
consignes d'utilisation et mises en gar-
de du fabricant.
Il est nécessaire d'insister sur les aver-
tissements et de les comprendre.
Si l'utilisateur ne parle pas couramment
l'anglais, l'acheteur/le propriétaire doit
lire les consignes et mises en garde du
fabricant avec l'utilisateur dans la lan-
gue maternelle de ce dernier et s'assu-
rer qu'il en comprend bien le contenu.
Le propriétaire et/ou l'utilisateur doit se
familiariser avec les consignes du fabri-
cant et les conserver afin de pouvoir s'y
référer ultérieurement.
DANGER
Identifie “une situation de danger immi-
nent qui, si elle n'est pas évitée, entraî-
ne la mort ou des blessures graves”.
ATTENTION
Identifie “une situation de danger poten-
tiel qui, si elle n'est pas évitée, pourrait
entraîner la mort ou des blessures”.
PRUDENCE
Identifie “une situation de danger poten-
tiel qui, si elle n'est pas évitée, peut
éventuellement entraîner des blessures
légères ou modérées” ou des domma-
ges matériels.
NETTOYEUR HAUTE PRESSION - MANUEL D'UTILISATION
Caractéristiques
Max. Pression 1400 PSI
Débit d'eau 1,3 GPM
Ampérage 13 A
Tension 120 V
Réf. 1.672-370.0
N° de série
Service après-vente Kärcher CDN
Responsabilité du propriétaire/de
l'utilisateur
Symboles d'alerte de sécurité

Français 3
Description des éléments :
1 Interrupteur marche/arrêt
2 Connecteur du tube détergent de
succion
3 Sortie haute pression
4 Entrée d'eau avec raccord pour
tuyau d'arrosage
5 Tuyau d'aspiration du détergent
avec filtre
6 Lance Vario
7 Poignée-pistolet
8 Verrouillage de sécurité de la poi-
gnée pistolet
9 Tuyau à haute pression
10 Cordon d'alimentation
GENERALITES

4 Français
ATTENTION !
En utilisant ce produit, toujours ob-
server une certaine prudence élé-
mentaire, incluant notamment.
Lire toutes les instructions avant
d'utiliser l'appareil.
Afin de réduire les risques de bles-
sures, une surveillance attentive est
requise lorsqu'un appareil est utilisé
à proximité d'enfants.
Savoir comment arrêter l'appareil et
réduire la pression rapidement. Etre
parfaitement familiarisé avec les
commandes.
Rester attentif -- toujours regarder
ce que l'on fait.
Ne pas utiliser l'appareil en étant fa-
tigué ou sous l'influence de l'alcool
ou de drogues.
Ne laisser personne approcher la
zone de travail.
Ne pas se pencher ou se tenir sur un
support instable. Toujours rester en
équilibre.
Observer les instructions de mainte-
nance figurant dans le manuel.
Risque d'injection ou de blessures
sur des personnes - ne pas diriger le
jet sur des personnes.
Utilisés abusivement, les jets à hau-
te pression peuvent être dangereux.
Le jet ne doit jamais être dirigé sur
des personnes, des animaux, des
appareils électriques ou la machine
même.
Porter des lunettes de protection.
Ne pas utiliser d'acides, ni de sol-
vants dans la machine. Ces produits
peuvent nuire à la santé de l'opéra-
teur et causer des dégâts matériels
irréversibles à la machine.
 Afin de réduire le risque d'électrocution,
garder toutes les connexions au sec et
ne pas les laisser à terre. Ne pas tou-
cher la fiche avec les mains mouillées.
 Le verrouillage de sécurité de la poi-
gnée-pistolet EMPECHE d'actionner
accidentellement la gâchette. Le dis-
positif de sécurité NE VERROUILLE
PAS la gâchette en position actionnée.
ATTENTION
 NE PAS ASPERGER DES APPAREILS
OU CÂBLAGES ÉLECTRIQUES.
 NE PAS UTILISER AVEC DES LIQUI-
DES INFLAMMABLES OU DES PRO-
DUITS CHIMIQUES TOXIQUES.
 HAUTE PRESSION. NE PAS S’AP-
PROCHER DE LA BUSE
 RISQUE D'INJECTION : L'ÉQUIPE-
MENT PEUT CAUSER BLESSURES
GRAVES SI LE JET PÉNÈTRE SOUS
LA PEAU. NE PAS DIRIGER LE PIS-
TOLET SUR UNE PERSONNE OU
UNE QUELCONQUE PARTIE DU
CORPS. EN CAS DE PÉNÉTRATION,
DEMANDER IMMÉDIATEMENT DES
SOINS MÉDICAUX.
 CE SYSTÈME EST CAPABLE DE
PRODUIRE UNE PRESSION DE 1400
PSI. AFIN D'ÉVITER TOUT RISQUE
DE RUPTURE OU DE BLESSURE, NE
PAS UTILISER CETTE POMPE AVEC
DES ÉLÉMENTS DANS LA PRESSION
DE SERVICE NOMINALE EST INFÉ-
RIEURE À 1400 PSI (NOTAMMENT
LES POIGNÉES-PISTOLETS, LES
FLEXIBLES ET RACCORDS).
 COUPER LE COURANT ET RELÂ-
CHER LA PRESSION AVANT DE PRO-
CÉDER AU DÉPANNAGE, AU
NETTOYAGE OU À TOUT ENLÈVE-
MENT DE PIÈCE.
CONSIGNES DE SECURITE IMPORTANTES