Kärcher K 5 Premium User manual

K 5 Premium
English
59672370 (11/16)

2 English
Please read and comply with
these original instructions prior
to the initial operation of your appliance and
store them for later use or subsequent own-
ers.
Apart from the notes contained herein the
general safety provisions and rules for the
prevention of accidents of the legislator
must be observed.
Warnings and notes that are attached on
the appliance provide important notes for
the safe operation.
This high pressure cleaner is designed for
domestic use only.
– for cleaning machines, vehicles, build-
ings, tools, facades, terraces, garden-
ing tools, etc. by means of a high-pres-
sure water jet (if necessary, with addi-
tional cleaning agents).
– with accessories, replacement parts
and cleaning agents approved by
KÄRCHER. Please observe the infor-
mation accompanying the cleaning
agents.
DANGER
Pointer to immediate danger, which leads
to severe injuries or death.
몇WARNING
Pointer to a possibly dangerous situation,
which can lead to severe injuries or death.
몇CAUTION
Pointer to a possibly dangerous situation,
which can lead to minor injuries.
ATTENTION
Pointer to a possibly dangerous situation,
which can lead to property damage.
Contents
Safety instructions. . . . . . . . . . . . . . . . 2
Environmental protection . . . . . . . . . . 5
Description of the Appliance . . . . . . . . 6
Assembly . . . . . . . . . . . . . . . . . . . . . . 7
Start up . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation . . . . . . . . . . . . . . . . . . . . . . 9
Transport. . . . . . . . . . . . . . . . . . . . . . . 10
Storage . . . . . . . . . . . . . . . . . . . . . . . . 11
Care and maintenance . . . . . . . . . . . . 11
Troubleshooting . . . . . . . . . . . . . . . . . 12
Accessories and Spare Parts . . . . . . . 13
Warranty . . . . . . . . . . . . . . . . . . . . . . . 13
Technical specifications . . . . . . . . . . . 13
Illustration . . . . . . . . . . . . . . . . . . . . . . 15
Safety instructions
Proper use
Hazard levels

English 3
DANGER
Risk of electric shock.
Never touch the mains plug and the
socket with wet hands.
Check the power cord with mains plug
for damage prior to every use. Immedi-
ately have damaged power cord re-
placed by an authorised customer ser-
vice / electrician. Do not operate an ap-
pliance if the power cord is damaged.
All current-conducting parts in the work-
ing area must be protected against jet
water.
The mains plug and the coupling of an
extension cable must be watertight and
must never lie in water. Moreover, the
coupling may never lie on the ground.
The use of cable reels that ensure that
the sockets are at least 60 mm above
the ground is recommended.
Make sure that the power cord or exten-
sion cable is not damaged by running
over, pinching, dragging or the like. Pro-
tect the power cords from heat, oil, and
sharp edges.
Turn off the appliance and remove the
mains plug prior to any care and main-
tenance works.
Repair work and work on the electrical
components may only be performed by
an authorised customer service.
몇WARNING
The appliance may only be connected
to an electric supply that has been in-
stalled by an electrician in accordance
with IEC 60364.
The appliance may only be connected
to alternating current. The voltage must
correspond with the type plate of the
appliance.
For safety reasons, we recommend that
you operate the appliance only via a re-
sidual current device (max. 30 mA).
Safety class I - Appliances may only be
connected to sockets with proper earth-
ing.
An unsuitable electrical extension cable
can be hazardous. Only use an electri-
cal extension cable which has been ap-
proved and labelled for this purpose
and has an adequate cable cross-sec-
tion outdoors: 1 - 10 m: 1.5 mm2;
10 - 30 m: 2.5 mm2
Always fully unreel the extension cable
from the cable drum.
DANGER
The user must use the appliance as in-
tended. The person must consider the
local conditions and must pay attention
to other persons in the vicinity when
working with the appliance.
Check important components, such as
high-pressure hose, hand spray gun
and safety installations, for damage pri-
or to every operation. Immediately re-
place damaged components. Do not
operate appliance with damaged com-
ponents.
High-pressure jets can be dangerous if
improperly used. The jet may not be di-
rected at persons, animals, live electri-
cal equipment or at the appliance itself.
The high-pressure jet must not be di-
rected at other persons or the user him-
/herself to clean clothing or footwear.
Vehicle tyres/tyre valves are suscepti-
ble to damage from the high-pressure
jet and may burst. The first indication for
this is a discolouration of the tyre. Dam-
aged vehicle tyres/tyre valves are peril-
ous. Keep a minimum jet distance of
30 cm during cleaning!
몇WARNING
Do not use the appliance when there
are other persons around unless they
are also wearing protective clothing.
The appliance must not be operated by
children or persons who have not been
instructed accordingly.
Electric components
Safe handling

4 English
This appliance is not intended for use
by persons with limited physical, senso-
ry or mental capacities or lacking expe-
rience and/or skills, unless such per-
sons are accompanied and supervised
by a person in charge of their safety or
they have received precise instructions
on the use of this appliance and have
understood the resulting risks.
Children must not play with this appli-
ance.
Supervise children to prevent them
from playing with the appliance.
몇CAUTION
Create stability for the appliance prior to
any work on or with the appliance to
prevent accidents or damage.
The water jet that is emitted from the
high-pressure nozzle results in a repul-
sion power acting on the hand spray
gun. Make sure that you have a firm
footing and are also holding the hand
spray gun and spray lance firmly.
Never leave the appliance unattended
as long as it is in operation.
ATTENTION
In case of extended breaks, switch off
the appliance at the appliance switch.
Do not operate the appliance at temper-
atures below 0 °C.
DANGER
The appliance may not be operated in
explosive atmospheres.
Never use the appliance to clean ob-
jects containing hazardous substances
(e.g. asbestos).
Do not spray flammable liquids.
Never draw in fluids containing solvents
or undiluted acids and solvents! This in-
cludes petrol, paint thinner and heating
oil. The spray mist is highly inflamma-
ble, explosive and poisonous. Do not
use acetone, undiluted acids and sol-
vents, as they corrode the materials
used on the appliance.
Keep packaging films away from chil-
dren, there is a risk of suffocation!
몇WARNING
According to applicable regulations, the
appliance must never be used on the
drinking water net without a system
separator. Ensure that the connection
of your building water installation on
which the high-pressure cleaner is op-
erated is equipped with a system sepa-
rator pursuant to EN 12729 Type BA.
Water that has flown through a system
separator is no longer classified as
drinking water.
High-pressure hoses, fixtures and cou-
plings are important for the safety of the
appliance. Only use high-pressure hos-
es, fixtures and couplings recommend-
ed by the manufacturer.
When disconnecting the supply or high
pressure hose, hot water may leak from
the connections after operation.
몇CAUTION
Mind the weight of the appliance when
selecting the storage location and dur-
ing transport (see technical data) to pre-
vent accidents or injuries.
몇CAUTION
Wear protective clothing and safety
goggles to protect against splash back
containing water or dirt.
During the use of high-pressure clean-
ers aerosols can develop. Inhaling aer-
osols can cause health damage.
–Depending on the application, com-
pletely shielded nozzles (e.g. surface
cleaner) that significantly reduce the
emission of aqueous aerosols can be
used for high-pressure cleaning.
–The use of such shielding is not possi-
ble with all applications.
–If the use of a completely shielded noz-
zle is not possible, a respirator of the
category FFP 2 or the like should be
used, depending on the environment to
be cleaned.
Other risks
Personal protective equipment

English 5
몇CAUTION
Safety installations serve the protection
of the user and may not be modified or
bypassed.
The appliance switch prevents unintention-
al operation of the appliance.
This lock locks the lever of the trigger gun
and prevents the inadvertent start of the ap-
pliance.
The overflow valve prevents the permissi-
ble working pressure from being exceeded.
If the lever on the trigger gun is released
the pressure switch turns off the pump, the
high pressure jet is stopped. If the lever is
pulled the pump is turned on again.
The motor protection switch switches off
the device if the power consumption is high.
Notes about the ingredients (REACH)
You will find current information about the
ingredients at:
www.kaercher.com/REACH
Symbols on the machine
The appliance must not be direct-
ly connected to the public drink-
ing water network.
The high pressure jet must not be
directed at persons, animals, live
electrical equipment or at the ap-
pliance itself.
Protect the appliance against
frost.
Safety Devices
Appliance switch
Lock trigger gun
Overflow valve with pressure switch
Motor protection switch
Environmental protection
The packaging material can be recy-
cled. Please arrange for the environ-
mentally appropriate disposal of the
packaging.
Old appliances contain valuable recy-
clable materials that should be recy-
cled properly. Please arrange for the
environmentally appropriate disposal
of the old devices.
Electrical and electronic devices of-
ten contain components which could
potentially pose a danger to human
health and the environment if handled
or disposed of incorrectly. However,
these components are necessary for
the proper operation of the device.
Devices marked with this symbol
must not be disposed of with regular
household rubbish.
Cleaning operations which produce
oily waste water, e.g. engine washes,
underbody washes, may only be car-
ried out using washing stations
equipped with an oil separator.
Work with detergents must only be
performed on liquid-tight work surfac-
es with a connection to the sewer
system. Do not let release detergent
into waters or earth.
The extraction of water from public
waters is prohibited in some coun-
tries.

6 English
The scope of delivery of your appliance is illustrated on the packaging. Check the contents
of the appliance for completeness when unpacking.
In the event of missing accessories or any transport damage, please contact your dealer.
Description of the Appliance

English 7
1 Coupling element for water connection
2 Water connection with integrated sieve
3 Appliance switch „0/OFF“ / „I/ON“
4 High pressure hose
5 Dosage regulator for detergent
6 Storage for trigger gun
7 High-pressure hose drum
8 Transport handle
9 Hand crank for hose drum
10 Storage of Plug 'n' Clean detergent bot-
tle with detergent connection
11 Storage for accessories
12 Storage hook for mains connection cable
13 Mains cable with mains plug
14 Plug 'n' Clean detergent bottle with
locking lid
15 Wheels
16 Trigger gun
17 Lock trigger gun
18 Key to detach the high pressure hose
from the trigger gun
19 Spray lance with pressure regulation
(Vario Power)
Carrying out the most common cleaning
tasks. The work pressure can be stage-
lessly regulated between "Min" and
"Max". You can add detergent when
"Mix" is selected.
In order to adjust the working pressure, re-
lease the lever of the trigger gun and turn
the spray lance to the desired position.
20 Spray lance with Dirtblaster
For strong contaminations
– Minimum diameter, 1/2 inches (13 mm).
– Minimum length 7.5 m.
Mount loose parts delivered with appliance
prior to start-up.
Illustrations on Page 14
Illustration
Install the transport wheels.
Attach the wheel caps.
Illustration
Place the bottom holder into the recess-
es and push forward until it audibly
locks in.
Insert the top holder and push down all
the way.
Illustration
Press in the storage hook and lock it
into the top position.
Illustration
You will need the 2 included screws as well
as a Phillips screwdriver PH 2.
Slide the transport handle into the guide
and secure it with 2 screws.
Illustration
You will need the 2 included screws as well
as a Phillips screwdriver PH 2.
Insert both detergent hoses onto the
hose fittings.
Install the dosage regulator and con-
nect using 2 screws.
Note: During installation you must make
sure that the tongues of the dosage regula-
tor match up with the intended recesses in
the casing.
Description of the Appliance
Additionally required
• Water supply hose
Fabric-reinforced water hose with com-
mercially available coupling.
Assembly
Install wheels
Install the storage for trigger gun
Install the storage hook for the
mains connection cable
Install the transport handle
Install the dosage regulator for
detergent

8 English
Illustration
Slide the free end of the coiled high
pressure hose through the recesses on
the dosage regulator.
Insert the hose drum into the intakes on
the transport handle.
Insert the axle of the hand crank into the
guides.
Install the fixating plate and secure it
using 2 screws.
Press the connecting fitting from the
short high pressure hose into the brass
intake, secure with clamps.
Note: Make sure the connection nipple is
aligned correctly.
Illustration
Push the high pressure hose into the
trigger gun until it locks audibly.
Note: Make sure the connection nipple is
aligned correctly.
Check the secure connection by pulling
on the high pressure hose.
Illustration
Screw the coupling element to the wa-
ter connection on the appliance.
Park the appliance on an even surface.
Insert the mains plug into the socket.
For connection values, see type plate/tech-
nical data.
ATTENTION
Impurities in the water can damage the
high-pressure pump and the accessories.
For protection, the use of the KÄRCHER
water filter (optional accessory, order no.
4.730-059) is recommended.
Observe regulations of water supplier.
ATTENTION
Hose couplings made of metal with aquas-
top can damage the pump! Please use
plastic couplings or KÄRCHER brass cou-
plings.
Attach the water supply hose to the
coupling on the water connection.
Connect the water supply hose to the
water supply.
Completely open the water tap.
This high-pressure cleaner is suited to work
with the KÄRCHER suction hose with back-
flow valve (Optional accessory, order no.
4.440-238) to draw in surface water, e.g.
from water butts or ponds (see specifica-
tions for max. suction height).
Remove coupling from the water con-
nection.
Fill the suction hose with water.
Screw the suction hose into the water
connection of the appliance and insert it
into the water source (e.g. rainwater
drum).
Remove air from appliance before oper-
ation.
Turn on the appliance “I/ON”.
Unlock the lever on the trigger gun.
Pull on the lever of the trigger gun; the
device will switch on.
Let the appliance work until the water
exits at the hand spray gun without bub-
bles (max. 2 minutes).
Release the lever on the trigger gun.
Note: Release the lever of the trigger
gun; the device will switch off again.
High pressure remains in the system.
Lock the lever on the trigger gun.
Install the high pressure hose drum
Connect the high pressure hose to
the trigger gun
Installing coupling
Start up
Water supply
Water supply from mains
Drawing in water from open reservoirs

English 9
ATTENTION
Dry running of more than 2 minutes leads to
damage of the high-pressure pump. If the
appliance does not build up pressure within
2 minutes, switch the appliance off and pro-
ceed in accordance with the instructions in
Chapter "Troubleshooting".
몇CAUTION
Keep a distance of at least 30 cm when us-
ing the jet for cleaning painted surfaces to
avoid damage.
ATTENTION
Car tyres, paint or sensitive surfaces such
as wood should not be cleaned with the dirt
blaster, as there is a risk of damage.
Illustration
Push the spray lance into the trigger
gun and fasten it by turning it through
90°.
Illustration
Unwind the high pressure hose com-
pletely from the hose drum. Hold on to
the transport handle during this proce-
dure.
Note: If the hand crank is in its secured
position, fold it up first.
Turn on the appliance “I/ON”.
Unlock the lever on the trigger gun.
Pull on the lever of the trigger gun; the
device will switch on.
Note: Release the lever of the trigger
gun; the device will switch off again.
High pressure remains in the system.
DANGER
When using detergents, the material data
safety sheet issued by the detergent manu-
facturer must be adhered to, especially the
instructions regarding personal protective
equipment.
Most KÄRCHER detergents can be bought
ready to use in a Plug 'n' Clean detergent
bottle.
Note: Detergent can only be added when
the device is operated in low pressure
mode.
Use spray lance with pressure regula-
tion (Vario Power).
Turn the spray lance to "Mix" position.
Note: This will mix the detergent with
the water stream.
Illustration
Remove the lid from the Plug 'n' Clean
detergent bottle and press the deter-
gent bottle into the detergent connec-
tion with the opening facing down.
Illustration
Adjust the suction volume of the deter-
gent solution by means of the dosage
regulator for detergents.
- Medium quantity: Central position
- Large quantity: "+" position
- Small quantity: "-" position
Note: While using a high pressure exten-
sion hose, it‘s not possible to add deter-
gents from the Plug 'n' Clean detergent bot-
tle.
Use instead the foam nozzle to add deter-
gents.
Spray the detergent sparingly on the
dry surface and allow it to react, but not
to dry.
Spray off loosened dirt with the high
pressure jet.
Remove the Plug 'n' Clean detergent
bottle from the intake and close it with
the lid.
For storage, put the detergent bottle
into the retainer with the cap pointing
up.
Operation
High pressure operation
Operation with detergent
Recommended cleaning method
After operation with detergent

10 English
Release the lever on the trigger gun.
Lock the lever on the trigger gun.
Insert the trigger gun in its holder.
During longer breaks (more than 5 min-
utes), also turn the appliance off using
the "0/OFF" switch.
몇CAUTION
Only separate the high-pressure hose from
the hand spray gun or the appliance when
there is no pressure in the system.
After operation with detergent: Run the
machine for approximately 1 minute for
a clear rinse.
Release the lever on the trigger gun.
Turn off the appliance "0/OFF".
Disconnect the mains plug from the
socket.
Turn off tap.
Press the lever on the trigger gun to re-
lease any remaining pressure in the
system.
Lock the lever on the trigger gun.
Detach the appliance from the water
supply.
몇CAUTION
Risk of personal injury or damage!
Mind the weight of the appliance during
transport.
Pull the appliance by its transport han-
dle.
Prior to horizontal transport: Remove
the Plug 'n' Clean detergent bottle from
the intake and close it with the lid.
Secure the appliance against shifting
and tipping over.
Interrupting operation
Finish operation
Transport
When transporting by hand
When transporting in vehicles

English 11
몇CAUTION
Risk of personal injury or damage!
Consider the weight of the appliance when
storing it.
Park the machine on an even surface.
Press the disconnect on the trigger gun
and remove the high pressure hose
from the trigger gun.
Detach spray lance from the trigger
gun.
Engage the spray lance in its compart-
ment.
Insert the trigger gun in its holder.
Stow the power cord and the remaining
accessories on the appliance.
Illustration
Wind the entire high pressure hose onto
the hose drum by rotating the hand
crank counter-clockwise.
Prior to extended storage periods, as dur-
ing the winter, also observe the instructions
in the Care section.
ATTENTION
Appliances and accessories that are not
completely drained can be destroyed by
frost. Completely drain appliance and ac-
cessories and protect them against frost.
To avoid damage:
Detach the appliance from the water
supply.
Detach spray lance from the trigger gun.
Turn on the appliance “I/ON”.
Push the lever of the trigger gun until no
more water is escaping (approx. 1 min).
Release the lever of the trigger gun.
Lock the lever of the trigger gun.
Turn off the appliance "0/OFF".
Store the appliance and the entire ac-
cessories in a frost free room.
DANGER
Risk of electric shock.
Prior to all work on the appliance,
switch off the appliance and pull the
power plug.
Clean the sieve in the water connection
regularly.
ATTENTION
The sieve must not be damaged.
Remove coupling from the water con-
nection.
Illustration
Pull the sieve out using flat pliers.
Clean the sieve under running water.
Reinsert the sieve into the water con-
nection.
Storage
Storing the Appliance
Frost protection
Care and maintenance
Clean the sieve in the water
connection

12 English
You can rectify minor faults yourself with
the help of the following overview.
If in doubt, please consult the authorized
customer service.
DANGER
Risk of electric shock.
Prior to all work on the appliance,
switch off the appliance and pull the
power plug.
Pull on the lever of the trigger gun; the
device will switch on.
Check whether the voltage indicated on
the type plate corresponds to the volt-
age of the mains supply.
Check the mains connection cable for
damages.
Motor overloaded, the motor circuit
breaker has tripped.
– Turn off the appliance "0/OFF".
– Allow the device to cool down for one
hour.
– Switch on the device and put it into op-
eration again.
If the malfunction occurs repeatedly,
have the device checked by the cus-
tomer service.
Voltage reduction due to weak mains sup-
ply or when using an extension cable.
When switching on, first pull the lever of
the trigger gun and then switch the ap-
pliance switch to "I/ON".
Check setting at the spray lance.
Check water supply for adequate deliv-
ery rate.
Pull out the sieve in the water connec-
tion using flat-nose pliers and clean un-
der running water.
Appliance ventilation: Switch the appli-
ance on with the high-pressure hose
detached and operate (max. 2 minutes)
until the water exits the high-pressure
connection without bubbles. Switch off
appliance and reconnect high-pressure
hose.
Clean high-pressure nozzle: Remove
dirt and debris from the nozzle bore, us-
ing a needle and rinse through with wa-
ter from the front.
Check water flow quantity.
Slight leakage from the appliance pump
is normal. If the leakage increases con-
tact the authorized customer service.
Use spray lance with pressure regula-
tion (Vario Power).
Turn the spray lance to "Mix" position.
Check the settings at the dosage regu-
lator for detergent.
Check whether the Plug 'n' Clean deter-
gent bottle is placed into the detergent
connection facing down.
Check the detergent suction hose for
kinks.
Troubleshooting
Appliance is not running
Appliance does not start, motor
hums
Pressure does not build up in the
appliance
Strong pressure fluctuations
Appliance is leaking
No detergent infeed

English 13
Only use original accessories and spare
parts, they ensure the safe and trouble-free
operation of the device.
For information about accessories and
spare parts, please visit www.kaerch-
er.com.
The warranty terms published by the rele-
vant sales company are applicable in each
country. We will repair potential failures of
your appliance within the warranty period
free of charge, provided that such failure is
caused by faulty material or defects in man-
ufacturing. In the event of a warranty claim
please contact your dealer or the nearest
authorized Customer Service centre.
Please submit the proof of purchase.
Addresses can be found under:
www.kaercher.com/dealersearch
Subject to technical changes.
Accessories and Spare Parts
Warranty
Technical specifications
Electrical connection
Voltage 220
1~ 50
V
Hz
Connected load 2,1 kW
Protection class IP X5
Protective class I
Water connection
Max. feed pressure 0,8 MPa
Max. feed temperature 40 °C
Min. feed volume 10 I/min
Max. Suction height 0,5 m
Performance data
Working pressure 12,5 MPa
Max. permissible pressure 14,5 MPa
Water flow rate 7,5 I/min
Max. flow rate 8,3 I/min
Detergent flow rate 0-0,3 I/min
Recoil force of trigger gun 20 N
Dimensions and weights
Length 349 mm
Width 426 mm
Height 878 mm
Weight, ready to operate
with accessories
15,3 kg

14 English
Illustration

English 15
Illustration

Alfred Kärcher GmbH & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Tel.: [phone]
Fax: [phone]
http://www.kaercher.com/dealersearch

15
مﻮﺳر

14
مﻮﺳر

13
.ﻞﻳﺪﻌﺘﻠﻟ ﺔﻌﺿﺎﺧ ﺔﻴﻨﻔﻟا تﺎﻔﺻاﻮﻤﻟا
ﺔﻴﻨﻔﻟا تﺎﻧﺎﻴﺒﻟا
ﻲﺋﺎﺑﺮﻬﻜﻟا ﻞﻴﺻﻮﺘﻟا
ﻲﺋﺎﺑﺮﻬﻜﻟا ﺪﻬﺠﻟا220
1~ 50
V
Hz
ﻞﻴﺻﻮﺘﻟا ﻚﻠﺳ2,1kW
ﺔﻳﺎﻤﺤﻟا ﺔﺟردIP X5
ﺔﻳﺎﻤﺤﻟا ﺔﺌﻓI
هﺎﻴﻤﻟا ﺔﻠﺻو
ﻷا ﺪﺤﻟا) ﻖﻓﺪﺘﻟا ﻂﻐﺿ(ﻰﺼﻗ0,8MPa
ﺪﺤﻟا) ﻖﻓﺪﺘﻟا ةراﺮﺣ ﺔﺟرد
ﻷا(ﻰﺼﻗ
40°C
ﻷا ﺪﺤﻟا) ﻖﻓﺪﺘﻟا ﺔﻴﻤﻛ(ﻰﻧد10l/min
ﻷا ﺪﺤﻟاﻻ ﻰﺼﻗﻂﻔﺸﻟا عﺎﻔﺗر0,5م
ةرﺪﻘﻟا تﺎﻧﺎﻴﺑ
ﻞﻤﻌﻟا ﻂﻐﺿ12,5MPa
ﻪﺑ حﻮﻤﺴﻣ ﻂﻐﺿ ﻰﺼﻗأ14,5MPa
هﺎﻴﻤﻟﺎﻘﻓﺪﺗ ﺔﻴﻤﻛ7,5l/min
ﻷا ﺪﺤﻟا) ﻖﻓﺪﺗ ﺔﻴﻤﻛ(ﻰﺼﻗ8,3l/min
ﻒﻴﻈﻨﺘﻟا داﻮﻣ ﻖﻓﺪﺗ ﺔﻴﻤﻛ0-0,3l/min
يوﺪﻴﻟا شﺮﻟا سﺪﺴﻣ داﺪﺗرا ةﻮﻗ20N
ﻷاو ﺲﻴﻳﺎﻘﻤﻟانازو
لﻮﻄﻟا349mm
ضﺮﻌﻟا426mm
ﻻاعﺎﻔﺗر878mm
ﻊﻣ ﻞﻤﻌﻠﻟ ﺰﻫﺎﺟ زﺎﻬﺠﻟاو نزﻮﻟا
ﺔﻴﻠﻴﻤﻜﺘﻟا تﺎﻘﺤﻠﻤﻟا
15,3kg