Kärcher Chariot 2 iVACUUM 24 130 A/H User manual

Register
your product
www.kaercher.com/welcome
86446760 - A01/25/21
Chariot 2 iVac 24 ATV English 02
Español 47

2
Warranty Registration
Thank you for purchasing a Kärcher North America product. Warranty registration is quick
and easy. Your registration will allow us to serve you better over the lifetime of the product.
To register your product go to :
http://warranty.karcherna.com
For customer assistance:
1-800-444-7654
8.644-676.0 Operator’s Manual - iVac 24 ATV
Machine Data Label / Overview
OVERVIEW
The Chariot® iVacuum 24™ is a battery powered, stand-on, wide area vacuum intended for commercial use. The
Chariot® iVacuum 24™ brushes and vacuums debris from indoor hard and carpeted surfaces and deposits the
debris in the debris tray and filter bags.
The unit also has an accessory wand and hose for cleaning small areas and non-floor surfaces.
Models:
1.008-067.0 iVACUUM 24, 130 A/H
1.008-068.0 iVACUUM 24, 114 A/H AGM
1.008-069.0 iVACUUM 24, 114 A/H AGM OBC
1.008-070.0 iVACUUM 24 OBC PACKAGING ONLY

3
Table of Contents
Machine Data Label / Overview . . . . . . . . . . . . . . . 2
Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How To Use This Manual. . . . . . . . . . . . . . . . . . . . . 4
Safety Label Locations . . . . . . . . . . . . . . . . . . . . . . 4
Safety
Safety Label Locations . . . . . . . . . . . . . . . . . . . . . . 5
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . 6
HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . 8
Operations
Technical Specifications . . . . . . . . . . . . . . . . . . . . 10
How This Machine Works . . . . . . . . . . . . . . . . . . . 12
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Drive Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Vacuum Controls. . . . . . . . . . . . . . . . . . . . . . . . . . 18
Pre-run Machine Inspection . . . . . . . . . . . . . . . . . 19
Emergency Stop Procedures . . . . . . . . . . . . . . . . 19
Normal Vacuuming . . . . . . . . . . . . . . . . . . . . . . . . 20
To Begin Vacuuming . . . . . . . . . . . . . . . . . . . . . . . 20
To Stop Vacuuming. . . . . . . . . . . . . . . . . . . . . . . . 21
Changing Vacuum Bag . . . . . . . . . . . . . . . . . . . . . 21
Maintenance
Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . 22
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Delta Q IC650 Charger Maintenance Instructions. 29
Delta Q IC650 Charger Operating Instructions . . 30
Selecting a Charge Profile. . . . . . . . . . . . . . . . . . . 31
Configuring the IC650 Charger Using a USB Flash
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Charge Tracking Data . . . . . . . . . . . . . . . . . . . . . . 33
Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Vacuum Diverter Valve Maintenance . . . . . . . . . . 35
Brush Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Brush Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 37
Debris Tray Removal. . . . . . . . . . . . . . . . . . . . . . . 37
Debris Tray Installation . . . . . . . . . . . . . . . . . . . . . 37
Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 37
Remove Brush Deck . . . . . . . . . . . . . . . . . . . . . . . 38
Replace Brush Deck Motor . . . . . . . . . . . . . . . . . . 38
Brush Motor Carbon Brush Replacement . . . . . . . 38
Drive Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Drive Motor Carbon Brush Replacement . . . . . . . 40
Drive Chain Tension . . . . . . . . . . . . . . . . . . . . . . . 40
Machine Tie-Downs. . . . . . . . . . . . . . . . . . . . . . . . 42
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Battery Discharge Indicator Troubleshooting . . . . 45
Suggested Spare Parts . . . . . . . . . . . . . . . . . . . . . 46
8.644-676.0 Operator’s Manual - iVac 24 ATV

4
How To Use This Manual
This manual contains the following sections:
• How to Use This Manual
•Safety
• Operations
• Maintenance
The HOW TO USE THIS MANUAL section will tell you
how to find important information for ordering correct
repair parts.
Parts may be ordered from authorized dealers. When
placing an order for parts, the machine model and
machine serial number are important. Refer to the
MACHINE DATA box which is filled out during the
installation of your machine. The MACHINE DATA box
is located on the inside of the front cover of this manual.
The model and serial number of your machine is
located on the back of the machine.
The SAFETY section contains important information
regarding hazardous or unsafe practices of the
machine. Levels of hazards are identified that could
result in product damage, personal injury, or severe
injury resulting in death.
The OPERATIONS section is to familiarize the operator
with the operation and function of the machine.
The MAINTENANCE section contains preventive main-
tenance to keep the machine and its components in
good working condition. They are listed in this general
order:
• Batteries
•BrushDeck
• Drive Motor
• Service Schedule
• Machine Troubleshooting
The manual part number is located on the lower right
corner of the front cover.
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
8.644-676.0 Operator’s Manual - iVac 24 ATV

5
Safety
8.644-676.0 Operator’s Manual - iVac 24 ATV
Safety Label Locations
These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible,
promptly replace them.
Emplacement De L'étiquette De Sécurité
REMARQUE : Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment,
les étiquettes deviennent illisibles, contactez votre représentant autorisé pour un remplacement rapide.
CAUTION
BATTERY
86252520 86385070
WARNING
MOVING PARTS
CAUTION
CAUTION LABEL
86244310

6
Safety
IMPORTANT SAFETY INSTRUCTIONS
When using this machine, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
Use only indoors. Do not use outdoors or expose to rain. This appliance is for dry use only.
Use only as described in this manual. Use only manufacturer's recommended components and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it
to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is not suitable for picking up hazardous dust.
Do not operate this machine near flammable fluids, dust or vapors.
Maintenance and repairs must be done by qualified personnel.
Disconnect battery before cleaning or servicing.
Before the machine is discarded, the batteries must be removed and properly disposed of.
Make sure all warning and caution labels are legible and properly attached to the machine.
During operation, attention shall be paid to other persons, especially children.
Before use, all covers and doors shall be put in the positions specified in the instructions.
When leaving unattended, secure against unintentional movement.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.
This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other
brushes may affect its safety.
Do not use on surfaces having a gradient of over 10% (6 degrees).
SAVE THESE INSTRUCTIONS
8.644-676.0 Operator’s Manual - iVac 24 ATV

7
Safety
MESURES DE SÉCURITÉ IMPORTANTES
Lors de l'utilisation d'un appareil à batteries, il est nécessaire de respecter systématique-
ment des mesures de sécurité de base, comme suit :
NOTE DE TOUTES CES MESURES AVANT D'UTILISER CETTE MACHINE.
Pour réduire les risques d'incendie, de chocs électriques, ou de blessures :
N'utiliser cette machine qu'en intérieur. Ne jamais l'utiliser à l'extérieur ou dans la pluie.
Utiliser cet appareil conformément aux instructions du présent manuel uniquement. N'utiliser que les
composants et les accessoires conseillés par le fabricant.
Lorsque la machine ne fonctionnant pas correctement, a fait l'objet d'une chute ou d'une détérioration, a été laissée
à l'extérieur, est tombée dans l'eau, la retourner au centre de service agréé.
Ne pas opérer la machine lorsque les conduits de ventilation sont bloquées. Débarrasser les débris des conduits,
car ils peuvent réduire l'écoulement d'air.
Cette machine n'est pas adaptée au ramassage de poussières dangereuses
Ne pas l'utiliser près de liquides, de poussières ou de vapeurs inflammables.
L'entretien et les réparations de la machine doivent être effectuées par un personnel qualifié.
Déconnecter les batteries avant de nettoyer la machine ou de la soumettre à un entretien.
Avant de se débarrasser de la machine, il est nécessaire de retirer les batteries et de les jeter correctement.
S'assurer que toutes les plaques d'avertissement ou de précaution sont lisibles et fixées correctement sur la
machine.
Durant la manoeuvre de la machine, prendre garde aux personnes environnantes et notamment aux enfants.
Avant l'utilisation de la machine, veiller à positionner tous les couvercles et portes comme indiqué dans les instruc-
tions.
Lorsque la machine est laissée sans surveillance, s'assurer qu'elle ne se déplace pas de manière accidentelle.
Cette machine ne doit être manoeuvrée que par un personnel expérimenté et qualifié.
Lorsque la machine est laissée sans surveillance, la mettre hors tension ou verrouiller l'interrupteur principal afin
d'empêcher un emploi non autorisé.
Cette machine a été conçue pour être utilisée avec des brosses spécifiées par le fabricant. L'utilisation d'autres
brosses peut affecter sa sûreté.
N'employez pas sur des surfaces ayant un gradient de plus de 10% (6 degrés).
CONSERVER CES INSTRUCTIONS
8.644-676.0 Operator’s Manual - iVac 24 ATV

8
Safety
8.644-676.0 Operator’s Manual - iVac 24 ATV
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY.
The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating
condition. Following is information that signals some potentially dangerous conditions to the operator or the equip-
ment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the
machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use
Kärcher North America approved replacement parts.
Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep battery
compartment open during charging. Keep sparks and flames away from the batteries. Do not smoke around
batteries.
Disconnect batteries before working on machine. Only qualified personnel should work inside machine.
Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact
with the acid contained in the batteries.
Never allow metal to lie across battery tops.

9
Safety
Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions :
DEGRÉS DE RISQUES EN CAS DE DANGER
Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR
VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante:
AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou
entraîner la mort.
ATTENTION - Dangers ou méthodes dangereuses qui pourraient provoquer des blessures légères ou une détério-
ration du produit ou des biens immobiliers.
POUR VOTRE SÉCURITÉ: ce signe permet d'identifier les mesures de précaution à prendre pour assurer un bon
fonctionnement du matériel.
Rendre compte immédiatement d'une défaillance ou d'une détérioration de la machine. Ne pas utiliser la machine
si celle-ci ne fonctionne pas correctement. Lire soigneusement les informations ci-dessous signalant certains
dangers potentiels pour l'opérateur de la machine. L'opérateur doit être absolument au courant de ces dangers
potentiels. Localiser tous les dispositifs de sécurité sur la machine. Il est conseillé de prendre les mesures néces-
saires pour former le personnel opérateur.
POUR VOTRE SÉCURITÉ:
NE PAS MANOEUVRER LA MACHINE:
Lorsqu'on n'est pas expérimenté ou qualifié.
Lorsque le guide d'utilisation n'est pas été lu ou compris.
Dans des zones inflammables ou explosives.
Dans des zones où des objets peuvent tomber.
LORS DE L'ENTRETIEN DE LA MACHINE:
Éviter les parties amovibles. Ne pas porter de vêtements amples, tels que des vestes, des chemises ou des
vêtements avec manches lors de l'utilisation de la machine. Utiliser les pièces détachées Kärcher North America
homologuées.
Les batteries émettent le gaz d'hydrogène. L'explosion ou le feu peut résulter. Étincelles de subsistance et
flamme nue loin. Compartiment de batterie de subsistance ouvert en chargeant. Étincelles et flammes de
subsistance loin des batteries. Ne fumez pas autour des batteries.
Déconnecter les batteries avant de travailler sur la machine. La machine ne doit être confiée qu'à un
personnel qualifié. Porter systématiquement des lunettes et des vêtements de protection lors d'une inter-
vention sur les batteries ou aux alentours. Éviter tout contact de la peau avec l'acide contenu dans les
batteries.
Ne jamais placer d'objets métalliques sur le dessus des batteries.
8.644-676.0 Operator’s Manual - iVac 24 ATV

10
Operations
Technical Specifications
ITEM DIMENSION/CAPACITY
Nominal power 1224 W
Rated Voltage 36 Volts DC
Rated Amperage 34 amps
Batteries 3 X12 Volt 130 AH @ 20 hr. rate
Battery Compartment Dimensions 20-1/2 in. x 13 in. x 10 in. tall (330mm x 521mm x 254mm)
Propelling Motor .38 HP (280 W)
Cylindrical Brush Motor .5 HP (373 W)
Side Broom Motor .06 HP (47W)
Cylindrical Brushes Two 20 in. (51cm) by 4 in. (10cm) diameter
Side Broom 9 in. (229 mm) diameter
Cylindrical Brush speed 1030 RPM
Side Broom speed 90 RPM
Vacuum Motor .63 HP (470 W)
Maximum flow rate of vacuum motor 72 cfm (33.98 liters per second)
Maximum suction of vacuum motor 47.3 inches of water (11.7 kPa)
Bag Capacity 1100 in³ 18L
Mass (GVW) 613 lbs (280 kg)
Weight empty without batteries 250 lbs (115 kg)
Tires 8 in. (203mm) drive, 6 in. (156mm) rear, polyurethane
Maximum Speed 2.3 mph (3.7 KPH)
Brake Electrical parking brake,sets automatically whenever operator stops.
Minimum aisle u-turn width 51 in. (1295 mm)
Maximum rated climb and descent angle 10% (6 degrees)
Sound power dBA (IEC 60704-1) 80.6 dBA
Sound pressuer dBA (IEC 60704-1) 68.4 dBA
Vibration arms m/s² (ISO 5344) 1.6 m/s²
Vibration feet m/s² (ISO 5344) 0.54 m/s²
Sound power uncertainty dBA 3.00 dBA
Sound pressure uncertainty dBA 3.00 dBA
Vibration uncertainty m/s² 0.50 m/s²
8.644-676.0 Operator’s Manual - iVac 24 ATV

11
Operations
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
Cet appareil n'est pas prévu à l'usage des personnes (enfants y compris) avec des possibilités physiques,
sensorielles ou mentales réduites, ou le manque d'expérience et de connaissance, à moins qu'ils aient été
donnés la surveillance ou l'instruction au sujet de l'utilisation de l'appareil par une personne chargée de
leur sûreté. Des enfants devraient être dirigés pour s'assurer qu'ils ne jouent pas avec l'appareil.
ITEM MEASURE
Height 51.8 in (1316 mm)
Length 44.0 in (1118 mm)
Width without deck 24.5 in (622 mm)
Width of deck 23.25 in (581 mm)
Width with side broom 25.9 in (658 mm)
LENGTH WIDTH
HEIGHT
8.644-676.0 Operator’s Manual - iVac 24 ATV

12
Operations
How This Machine Works
The Chariot® iVacuum 24 ATV™ is a battery powered,
self-propelled, vacuum intended for commercial use.
The appliance vacuums debris and dirt from the carpet
and collects it in a disposable bag.
The machine's primary systems are the brush system,
vacuum system, and operator control system.
The function of the brush system is to brush the carpet.
The brush system consists of two cylindrical type
brushes, side brush, motors, brush deck, and controls.
The right side brush is used to sweep debris from along
edges into the path of the brush deck.The front
cylindrical brush sweeps debris backwards. The rear
brush sweeps debris forwards. Both cylindrical brushes
work to agitate the carpet and to route the debris up
into the debris tray assembly.
The function of the vacuum system is to vacuum fine
dirt and debris into the vacuum bag. The recovery
system consists of the debris tray assembly, vacuum
motor, paper vacuum bag and post filter. The vacuum
draws the dirt off the floor as the machine moves
forward. The vacuum motor provides suction to draw
the fine dirt into the vacuum bag, and the debris tray
holds large debris. The vacuum bag holds the fine dirt.
The function of the operator control system is to control
the direction and speed of the machine. The directional
control system consists of the direction control switch,
throttle pedal, speed control switch, drive reset switch,
emergency stop/brake switch, steering wheel, propel
controller and drive wheel. The directional control
switch signals forward or reverse direction. The
controller interprets signals from the throttle pedal to
command the drive wheel to propel or slow the
machine. The drive reset switch is to make sure the
operator is on platform before machine will propel. The
steering wheel points the drive wheel in the direction
desired by the operator. The parking brake
automatically engages when the operator steps off the
platform. The emergency stop/brake can be used to
hold the machine on slopes.
8.644-676.0 Operator’s Manual - iVac 24 ATV

13
Operations
Components
1. Accessory Hose
2. Brush Deck
3. Console
4. Control Panel
5. Main Cover
6. Pedal Platform
7. Rear Cover
8. Side Broom
9. Vacuum Bag
1
2
3
4
5
6
7
8
9
8.644-676.0 Operator’s Manual - iVac 24 ATV

14
Operations
Drive Controls
1
2
3
4
5
6
7
89
10
8.644-676.0 Operator’s Manual - iVac 24 ATV

15
Operations
1. Key Switch
2. Emergency Stop/Brake Switch
3. Directional Control / Drive Reset Switch
4. Throttle Pedal
5. Horn Button
6. Steering Wheel
7. Speed Control
8. Battery Discharge Indicator Light
9. Hour Meter
10. Operator Presence Switch
1. KEY SWITCH
Controls the power for machine functions.
To turn the machine power on, rotate key clockwise.
To turn the machine off, rotate key counterclockwise.
When the key is turned on the battery discharge indicator light will flash once and stay on continuously.
2. EMERGENCY STOP/BRAKE SWITCH
This safety feature is designed to cut all power to the machine at any time and apply parking brake.
To shut the machine power off, push the Emergency Stop Switch, this will also engage the parking brake and
cause the machine to stop immediately.
To reset the machine, rotate the switch clockwise. The switch will pop-up indicating reset machine.
3. DIRECTIONAL CONTROL / DRIVE RESET SWITCH
This safety feature is designed to ensure safe engagement of propel drive. Each time the machine power is
turned on, or each time an operator steps on to the platform, the Drive Reset Switch must be pushed before
machine will propel.
The switch controls the direction of travel of the vehicle. The lighted arrow on the switch indicates direction of
travel.
To travel forward, press the top of the switch.
To travel in reverse, press the bottom of the switch.
8.644-676.0 Operator’s Manual - iVac 24 ATV

16
Operations
4. THROTTLE PEDAL
Controls the speed of the vehicle within the speed control setting selected. Pressing the pedal causes the
machine to travel in the direction selected by the Directional Control Switch.
To increase speed, increase pressure on the pedal.
To decrease speed, decrease pressure on the pedal.
5. HORN BUTTON
The horn is activated by pressing the horn button.
6. STEERING WHEEL
The steering wheel turns the front wheel causing the machine to change direction.
7. SPEED CONTROL
Controls the maximum speed of the machine. There are two travel-only settings, slow and fast.
To change speed, rotate the dial to either slow or fast position. The slow position is to the left (counterclock-
wise), fast to the right (top position).
The throttle pedal will always regulate the speed between 0 and maximum.
8.644-676.0 Operator’s Manual - iVac 24 ATV

17
Operations
8. BATTERY DISCHARGE INDICATOR
Indicates the charge level of the batteries.
The indicator will be illuminated if the batteries have a sufficient charge. A slow, continous flash indicates the
batteries require charging.
The Battery Lockout function will activate when the batteries are low.
Once active, the LED status indicator will begin to flash slowly and the controller will inhibit the side broom,
main brushes, and vacuum operation. The drive remains functional. Return the unit to the charging station and
charge the batteries.
NOTE: Continuing usage may damage the batteries.
When the machine is left overnight with less than a full charge, the display may initially indicate a full charge. It
will also indicate a full charge if the batteries are disconnected, then reconnected. After a few minutes of
operation the indicator will give the correct charge level.
9. HOUR METER
Records the number of hours the machine has been in vacuum operation. This information is useful in deter-
mining when to service the machine.
8.644-676.0 Operator’s Manual - iVac 24 ATV

18
Operations
Vacuum Controls
1. Function Mode Switch
The first two positions are for transport only. See drive controls section.
Light vacuuming
This mode is used for light vacuuming. In this mode the machine will propel at fast speed. The
‘floating’ brush deck is in the down position. The brushes will agitate, the side broom will bring
debris into the path of the deck. The vacuum will draw the dirt and debris into the debris tray and
the vacuum bag.
Deep vacuuming
This mode is used for deep vacuuming. In this mode the machine will propel at a slow speed. The
‘floating’ brush deck is in the down position. The brushes will agitate, the side broom will bring
debris into the path of the deck. The vacuum will draw the dirt and debris into the debris tray and
the vacuum bag.
Accessory mode
This mode is used for using the accessory hose and attachments only. The brush and vacuum
deck will both be up and off. In this mode the machine will not propel.
2. Vacuum Bag Status Light
Light is green when bag is in place and vacuum operating conditions are good.
Light is red if bag is missing or full or vacuum operating conditions are poor.
1
2
8.644-676.0 Operator’s Manual - iVac 24 ATV

19
Operations
Pre-run Machine Inspection
Do a pre-run inspection to find possible problems that
could cause poor performance or lost time from break-
down. Follow the same procedure each time to avoid
missing steps.
NOTE: See Maintenance Service Schedule for pre-
run machine inspection checklist items.
Starting Machine
NOTE: Perform pre-run machine check before
operating machine.
FOR SAFETY: Before starting machine, make sure that
all safety devices are in place and operating properly.
1. Push machine while off to verify parking brake is
functioning correctly.
2. Stand on the operator platform. Throttle pedal must
be in neutral position.
3. Turn the machine power on by turning key switch
clockwise to the “ON” position.
4. Check the position of the Directional Control
Switch to make sure the machine will travel in the
direction intended.
5. Press the Drive Reset Switch.
6. Press lightly on the throttle pedal with right foot.
Emergency Stop Procedures
1. Release the throttle pedal by lifting right foot.
2. Turn machine power off with key switch by turning
key switch counterclockwise.
3. If an electrical problem is suspected, push in
emergency stop button. This will also engage the
parking brake and cause the machine to stop
immediately.
8.644-676.0 Operator’s Manual - iVac 24 ATV

20
Operations
Normal Vacuuming
Plan the vacuuming pattern in advance. The longest
track is around the perimeter of the area to be cleaned.
For efficient operation, the runs should be the longest
possible without turning or stopping.
In order to achieve the best possible results, the area
which is to be cleaned should be picked up before
vacuuming. Large debris, strings and wire must be
removed to prevent being caught in brushes.
NOTE: Check and empty debris tray as needed
during operation.
If machine is allowed to stand in neutral with the
vacuum deck down for more than 2 seconds, the brush
motor stops. If either forward or reverse travel is
selected, the brush motor will continue once movement
of machine begins. Overlap the brush path and avoid
transporting over previously cleaned areas.
Recommended Path
To Begin Vacuuming
When operating the machine around people, pay
close attention for unexpected movement. Use
extra caution around children.
Lorsque vous utilisez la machine en présence de
gens, portez une attention particulière aux mouve-
ments inattendus. Soyez plus prudent, surtout en
présence d’enfants.
1. Stand on the operator platform. Throttle pedal must
not be depressed.
2. Turn key switch to turn machine power on.
3. Check position of Directional Control Switch to
ensure that machine is set to travel in direction
intended.
4. Rotate the Speed/Function Control Knob to one of
the two vacuum settings.
5. Drive machine forward to begin vacuuming.
6. Adjust the speed of the machine as necessary.
8.644-676.0 Operator’s Manual - iVac 24 ATV