Kärcher T 150 T-Racer User manual

T 150 T-Racer
Deck and Driveway Cleaner
59651730 07/14
English 4
Español 
Français 

2

English
WARNING
When using this product basic precau-
tions should always be followed, includ-
ing the following:
Read all the instructions before
using the product.
Please observe the safety instruc-
tions of your pressure washer.
The T-Racer must not be used by
children.
Only trigger the gun of the pressure
washer if the T-Racer is located on
the surface to be cleaned.
Keep all persons/animals clear of
the immediate vicinity of the cleaning
head.
Beware of the recoil force! Ensure a
stable position and firmly hold the trig-
ger gun with the extension handle.
Turn off the pressure washer when
examing or changing the T-Racer
and after the completion of the clean-
ing operation.
Maximum water temperature al-
lowed is 104 °F (40°C). Please follow
the instructions of your pressure
washer.
몇Caution
Do not use on windows.
The T-Racer is not suited for scour-
ing or scrubbing.
Do not run over freestanding cor-
ners.
Always test the T–Racer in an incon-
spicuous area.
Never operate in the same area for
more than 2 seconds, damage may
occur.
SAVE THESE INSTRUCTIONS!
When unpacking the product, make
sure that no accessories are missing
and that none of the package contents
have been damaged. If you detect any
transport damages please contact your
retailer.
Illustrations on Page 2
Illustration
1 Housing
2 Bayonet connection with union nut
3 Adapter
4 Wand
5 High pressure nozzle
6 Twin-jet rotating arm
Use on horizontal surfaces like drive-
ways, patios, side walks, etc.
The T-Racer has not been designed for
commercial use.
Danger!
Keep hands away from moving
parts.
Note: Always use Kärcher water filter
(order no. 4.730-059.0) during suction
operations of the pressure washer.
Safety instructions Preparing the Appliance
Description of the Appliance
Intended use
For pressure washers with a
pressure from 1400 psi to 1650 psi
Symbols on the appliance
Application
3EN

English
Insert the adapter into the casing.
Illustration
1 Take the adapter into the opening of
the casing.
2 Turn the adapter clockwise until it
snaps into place.
Note
Onetime installation. The adapter can-
not be unlocked anymore.
Connect the T-Racer and the wand with
the trigger gun.
Illustration
Connect wand with T-Racer.
1 Press the bayonet connection into
the bayonet catch, then turn by 90°
until it locks into place.
2 Tighten the union nut.
Connect trigger gun with wand.
1 Press the bayonet connection into
the bayonet catch, then turn by 90°
until it locks into place.
2 Tighten the union nut.
The T-Racer is not suited for scour-
ing or scrubbing.
Note: Outdoor surfaces should be
swept before the T-Racer is used to
avoid damaging the nozzles.
Guide the T-Racer over the surface
without effort.
Illustration
몇Caution
Do not run over freestanding corners.
Caution
Do not reach under the edge of the
T-Racer while the device is in opera-
tion.
Pressure washer does not build up
the pressure or is vibrating.
Dismantle the nozzles, check the
nozzles for damage, rinse the T-Rac-
er with clean water then reinstall the
nozzles.
Illustration
1 Remove the clip.
2 Pull out the high-pressure nozzle.
Rinse the high-pressure nozzle with
clean water, replace if necessary.
3 Insert the nozzle.
4 Re-insert the clip.
You can use the extension tube with any
Kärcher accessory.
Use a moist cloth and clean the appli-
ance after use.
Store the appliance in a frost free area.
The device can be suspended into the
KÄRCHER organizer for storage.
The appliance is maintenance free.
In the U.S. or Canada, please call
1-800-537-4129 for warranty issues and
visit www.karcher-help.com for techni-
cal support and product assistance.
Call: 01-800-024-13-13 for help or visit
our website: www.karcher.com.mx
Preparatory operations
Cleaning surfaces
Tips for cleaning
Troubleshooting
Cleaning the high-pressure
nozzle
General notes
Tip
Maintenance and care
Care
Maintenance
Customer Support
USA and Canada
Customer Support Mexico
4 EN