K Tool International KTI-XD63703 User manual

KTI-XD63703 rev. 03/12/21
4 TON PORTABLE RAM KIT
OWNERS MANUAL
SPECIFICATIONS
KTI-XD63703
Ram Capacity ................................................ 4 Ton @ 7,250 psig
Ram Minimum Height......................................................... 10.51"
Stroke.................................................................................... 4.72"
Fluid Capacity.................................................................. 12.8 oz.
Complies with ASME PASE-2019 Safety Standard
www.ktoolinternational.com

2
KTI-XD63703 rev. 03/12/21
WARNING
WARNING
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the
device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not
legible, contact K-Tool International for replacements. If the operator is not fluent in English, the product and safety instructions shall be
read to and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the
operator comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
The use of Portable Hydraulic Power Kits is subject to certain hazards that cannot be prevented by mechanical means, but only by the exer-
cise of intelligence, care, and common sense. The versatility of use is limited only by the imagination and ingenuity of its operator; therefore
K-Tool International cannot be responsible for product damage or personal injury due to faulty operator judgement or improper use of the
kit. It is essential to have personnel involved in the use and operation of the kit who are careful, competent, trained, and qualified in the safe
operation of the kit and its proper use when working on vehicle frames and body parts. Examples of hazards are dropping or slipping of
load, caused by improperly securing loads, overloading, off centered loads, and improper setups. Additional hazards may be caused by the
rupture or bursting of the hydraulic hoses and related fittings due to abuse, misuse, improper setup and using the kit for a purpose for which
it was not intended.
METHODS TO AVOID HAZARDOUS SITUATIONS
• Read, study, understand, and follow all instructions before operating this device.
• The kit owner is responsible for the kit being used in accordance with OSHA, state, and local safety standards.
• User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.
• Do not use beyond rated capacity.
• When attachments and adapters are used with the kit, the rated capacity of the kit shall be no greater than the rated capacity of the lowest
rated component or combination of components that makes up the kit. Refer to the Owner’s Manual section titled “APPLYING FORCE” for
typical applications and corresponding load capacities.
• Use a pressure gauge that indicates force applied.
• Spreader Ram is rated at 1/2 ton capacity.
• Rubber Heads are rated at 1/2 ton capacity in the 4 ton kit and 1 ton capacity in the 10 ton kit.
• Do not overextend the rams.
• When using extension tubes, position the shortest tube farthest away from the cylinder.
• Attachments and extension tubes must be aligned and fully engaged so the ram force is straight and avoids off-center conditions.
• Before operating, tighten all hose, gauge and manifold connections so they are secure and leak free. Do not over tighten or it may cause
  prematurethreadfailureorsplitpressurettings.Tightenallhosequickdisconnectttingsbyhandonly.
• Do not subject the hose to extreme heat or cold, sharp surfaces, abrasion, impact, kinking, twisting, curling, bending or any condition that
  restrictsoraffectsuidow.
• Make sure setup is stable and secure before performing any work.
• Use this kit for the intended purpose of vehicle body/frame repair only.
• Only components supplied with this kit shall be used with this kit.
 • Noalterationsormodicationsshallbemadetoanyofthekitcomponents.
• Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.
WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.
WARNING: Indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
WARNING
WARNING
WARNING INFORMATION

3
KTI-XD63703 rev. 03/12/21
PORTABLE HYDRAULIC POWER KIT SETUP INSTRUCTIONS
This is the Safety Alert Symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
SETUP
1. Refer to the parts list and drawing in this manual to identify parts mentioned in this setup procedure.
2. Before installing the force gage (P39) remove the plug A in the hose end of the pump (01). Thread the gage into the gage tting
(P41) and connect with the receiver (P42) by turning it clockwise. Make sure the connection is tight to prevent leakage.
3. Open the release valve (P29) by turning it counterclockwise until it stops, then pump the handle 4 or 5 full incremented pump
strokes to purge air from the hydraulic system.
4. Install ram (2) or spreader (3) at the end of hose (P30) and secure the quick disconnect ttings together by hand tightening the
threaded sleeve (R06) on the female coupler (R15) to the male coupler (P31) at the end of the hose (P30).
P39
P40
P41
P42
OPERATING INSTRUCTIONS
This is the Safety Alert Symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Study the work to be done in order to determine the type ram and other attachments you will be using. Consult the enclosed
chart titled “Applicable force for component set ups” in order to determine the maximum allowable force to be used in your
specific setup. All rams have female hose disconnects attached to them, and the end of the hose has the male quick disconnect
attached to it. Insert the end of the hose (P30) all the way in to the ram’s female quick disconnect (R15). Slide the female connector’s
threaded sleeve (R06) on to the threads at the end of the hose (P30) and hand tighten. Never use any tools to tighten this
connection.
2. Consult this Owner’s Manual section titled APPLICABLE FORCE FOR COMPONENT SET UPS for typical attachment and extension
tube setups and pay very close attention to the corresponding load ratings of certain attachment connections. The use of extension
tubes, ram or plunger toes greatly reduces the hydraulic system’s capacity. When using extension tubes, put the shortest tubes on
the ends of the setup.
3. The pump (1) may be operated in the horizontal or vertical position but the pump (1) must point down when used in the vertical
position.
4. Make sure all hydraulic and attachment connections are fully engaged and tight so ram force is straight in order to avoid off-center
load conditions.
5. During setup, make sure the hose routing avoids kinks, twists, curls or bends that will impede hydraulic uid ow. Do not use the
hose (P30) as a means to carry the kit components. Do not subject the hose (P30) to any hazards such as re, extreme heat or cold,
sharp surfaces, or heavy impact. IF A HOSE (P30) RUPTURES, BURSTS, OR NEEDS TO BE DISCONNECTED, IMMEDIATELY SHUT
THE PUMP (1) OFF AND OPEN THE RELEASE VALVE (P29) TO RELEASE HYDRAULIC PRESSURE. NEVER GRASP A LEAKING
PRESSURIZED HOSE, FITTING OR COMPONENT WITH YOUR HANDS OR SUFFER SERIOUS INJURY.
6. Always use the pressure gauge (14) to make sure you are within the required force range when operating the system.
7. In order to pump the ram (2), it will be necessary to turn the release valve knob (P29) in a clockwise direction until tight. Tighten by
hand only.
8. Pumping the handle (P34) up and down transfers the hydraulic uid from the pump’s reservoir (P6), through the hose (P30), in to the
cylinder and extends the ram with each incremental pump stroke.
9. To release the pressure and return the ram (2) back in to its cylinder (R13) , turn the release valve knob (P29) in a counterclockwise
direction very slowly. Turning the release valve knob (P29) slowly will determine the speed in which the ram (2) will retract back into
its cylinder (R13).
IMPORTANT: The pump includes an overload valve that will activate at the pump’s rated capacity only. If the setup requires a
reduced rating, the operator is responsible for using the gauge to determine when to stop pumping since the overload valve (P24) is
set to a higher rating.
10. Make sure the ram (2) is completely retracted inside its cylinder (R13) before disconnecting the hose from the cylinder.
11. The the hose (P30) and the ram (2) are repeatedly disconnected and exposed to shop or work place oors that are covered with dirt
and debris. It is important to use the dust caps (P32) provided to prevent contaminants from entering the air and hydraulic systems.
12. Based on continuous engagement and disengagement of the hose (P30) from the cylinder (R13), eventually it will become necessary
to add hydraulic uid to the pump’s reservoir (P6). Completely retract the ram before adding hydraulic uid. Do not overll in order
to avoid personal injury and hydraulic malfunction. Use only hydraulic jack oil, Chevron Hydraulic Oil AW ISO 32 or its equivalent
Unocal Unax AW 150. Other uids will cause damage to the hydraulic seals.

4
KTI-XD63703 rev. 03/12/21
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to
potential personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the kit in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust,
or any other harmful elements.
2. Based on continuous engagement and disengagement of the hose from the cylinder, eventually it will become necessary to add
hydraulic uid to the pump’s reservoir. Completely retract the ram before adding hydraulic uid. Do not overll in order to avoid personal
injury and hydraulic malfunction. Use only hydraulic jack oil, Chevron Hydraulic Oil AW ISO 32 or its equivalent Unocal Unax AW 150.
Other uids will cause damage to the hydraulic seals.
IMPORTANT: In order to prevent seal damage and kit failure, never use alcohol, hydraulic brake uid or transmission oil in the pump.
3. Every kit owner is responsible for keeping the kit labels clean and readable. Use a mild soap solution to wash external surfaces
of the kit components but not any moving hydraulic components.
4. Do not attempt to make any hydraulic repairs unless you are a qualied hydraulic repair person that is familiar with this equipment.
Repairs must be performed by an authorized service center.
TROUBLESHOOTING
PROBLEM: RAM WILL NOT LIFT RATED LOAD
ACTION: Turn reservoir fill screw (P7) counterclockwise two complete revolutions and wait 10 seconds. Turn screw clockwise
until tight and proceed to pump. If that does not fix the problem check the pump reservoir's fluid level. The proper amount
of fluid should be 12.8 ounces. Use only hydraulic jack oil. For any other problems contact K-Tool International hydraulic
service center.
Spreader Capacity
100% of Ram Capacity 100% of Ram Capacity
100% of Plunger Toe Capacity
25% of Ram Capacity
100% of Rubber Head Capacity
50% of Plunger Toe Capacity
25% of Ram Capacity
6% of Ram Capacity
APPLICABLE FORCE
FOR COMPONENT SET UPS
12% of Ram Capacity

5
KTI-XD63703 rev. 03/12/21
K-Tool International warrants that all XD and HD jacks and service-related equipment will be free from defects in material and
workmanship for a period of 2 years following the original date of purchase. This warranty is extended to the original retail purchaser
only. If any jack or service-related item proves to be defective during this period, it will be replaced or repaired, at K-Tool International’s
option, without charge. This warranty does not apply to damage from accident, overload, misuse or abuse, nor does it apply to any
equipment which has been altered or used with special attachments other than those recommended. This warranty does not cover
repairs made by anyone who is not a K-Tool International Professional Lifting Equipment Authorized Repair Center.
All HD and XD jacks or service-related equipment will be replaced or repaired at K-Tool International’s option during the 2 year warranty
period.
During the 2 year warranty period, all alleged defective products must be shipped, freight prepaid, along with proof of date-of-purchase,
to your nearest K-Tool International Professional Lifting Equipment Authorized Warranty Center. Be certain to include your name,
address and phone number along with proof-of-purchase information, and a brief description of the alleged defect. The product will be
returned to the customer, freight prepaid.
For more information regarding warranty and repair procedures, repair center locations, and troubleshooting tips please visit:
www.ktoolinternational.com/kti/warranty.
In no event shall K-Tool International be liable for incidental or consequential damages. The liability on any claim for loss or damage
arising out of the sale, resale or use of a jack or related service equipment, shall in no event exceed the purchase price. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED IN CONNECTION WITH THE SALE OF K-TOOL
INTERNATIONAL PROFESSIONAL LIFTING EQUIPMENT. ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE.
WARRANTY HANDLING PROCEDURES AND GUIDELINES FOR HD AND XD LIFTING EQUIPMENT

6
KTI-XD63703 rev. 03/12/21
Item # Part # Description Qty
1 RS6370308 Pump w/Hose 1
RSHS Hose 1
2 RS63703R Ram 1
3 RS6370310 Spreader 1
4 RS4T01 Case 1
5.1 RS6370302.1 3.23” (82mm) Extension 1
5.2 RS6370302.2 5.04” (128mm) Extension 1
5.3 RS6370302.3 8.50” (216mm) Extension 1
5.4 RS6370302.4 16.54” (420mm) Extension 1
5.5 RS6370302.5 19.49” (495mm) Extension 1
6 RS6370304 Ram Toe 1
Item # Part # Description Qty
7 RS6370305 Plunger Toe 1
8 RS6370306 Wedge Head 1
9 RS6370307 V-Base 1
10 RS4T08 Male Connector 1
11 RS6370309 Serrated Saddle 1
12 RS4T10 Rubber Head 1
13 RS6370303 Flat Base 1
14 RS6370311 Pressure Gauge Assembly 1
Not
Shown
RSKTIXD63703LK Product Label Kit 1
4 TON PORTABLE RAM KIT
4 TON RAM KIT
PARTS LIST AND DRAWING
KTI-XD63703
P39
P40
P41
P42
14

7
KTI-XD63703 rev. 03/12/21
4 TON PORTABLE RAM KIT
RS6370308
4 TON PUMP
PARTS LIST AND DRAWING
* Items identified by an asterisk are available in pump seal kit, RS63703PSK.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
KTI-XD63703
P1
P2
P3
P4
P5
P6
P25
P7
P10
P11
P12
P13
P14
P20
P18-1
P18-2
P17
P16
P15
P4
P8
P9
P10
P28
P29
P21
P22
P23
P24
P25
P26
P27
P31
P32
P30
P19
P34
P35
P36 P38
P37
P33
P37
P39
P40
P41
P42
P39
Item # Part # Description Qty
P1 Screw 1
P2 * O-ring 1
P3 RS63703P1 Pump Foot 1
P4 * O-ring 2
P5 Tie Rod 1
P6 Reservoir 1
P7 Breather Screw 1
P8 Oil Filter 1
P9 Valve Block 1
P10 * Ball 3
P11 * Ball 1
P12 * Spring 1
P13 * Washer 1
P14 Plug Screw 1
P15 * Copper Ring 1
P16 * Piston Seat 1
P17 * Anti-dust Ring 1
P18 * Sealing Ring (incl 18-1 & 18-2) 1
P19 Screw 1
P20 Piston 1
P21 * Ball 1
Item # Part # Description Qty
P22 * Ball Cup 1
P23 * Spring 1
P24 * Screw 1
P25 * O-ring 2
P26 Screw 1
P27 Screw Cap 1
P28 * O-ring 1
P29 RS63703P15 Release Valve 1
P30 RSHS Hose 1
P31 RSP17 Male Coupler 1
P32 RSP18 Hose Dust Cover 1
P33 Magnet 1
P34 RS630703P2 Handle 1
P35 Handle Sleeve 1
P36 Pin 1
P37 Sealing Ring 2
P38 Pin 1
P39 RS6370311 Pressure Gauge (incl P39 - P42) 1
P40 O-ring 1
P41 Gauge Fitting 1
P42 Nut 1

8
KTI-XD63703 rev. 03/12/21
RS6370310 - SPREADER PARTS BREAKDOWN
*Items identified by an asterisk are available in Ram Seal Kit, RS4TRSKA.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
*Items identified by an asterisk are available in Spreader Seal Kit, RS63703SSK.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
RS63703R - RAM PARTS BREAKDOWN
4 TON PORTABLE RAM KIT
KTI-XD63703
Item # Part # Description Qty
R01 RS4TR01 Cover 1
R02 Circlip 1
R03 Piston Rod 1
R04 * Circlip 1
R05 * Bushing 1
R06 Nut 1
R07 * Sealing Ring Set 1
R08 * Retaining Ring 1
R09 Spring 1
R10 Screw 1
R11 RS4TR12 Protection Cap 1
R12 Limit Ring 1
R13 Cylinder 1
R14 Screw 1
R15 Female Coupler 1
R16 O-ring 1
R17 Dust Cover 1
R18 Sealing Ring 1
N/S RS63703R01 Ram Coupler (incl R06,
R15–R18)
1
Item # Part # Description Qty
S1 Pin 1
S2 Circlip 1
S3 Movable Jaw 1
S4 Spring 1
S5 Fixed Jaw 1
S6 Piston 1
S7 * Cup Seal 1
S8 * O-ring 1
S9 End Cap 1
S10 Nut 1
S11 Coupler 1
S12 O-ring 1
S13 Dust Cover 1
S14 Sealing ring 1
N/S RS63703S01 Spreader Coupler (incl
S10 – S14)
1

9
KTI-XD63703 rev. 03/12/21
4 TON EQUIPO PORTÁTIL DE PISTONES
MANUAL DEL PROPIETARIO
ESPECIFICACIONES
KTI63703
Ram Capacity ................................................ 4 Ton @ 7,250 psig
Altura mínima del pistón ....................................... 267mm/10.51"
Recorrido ................................................................ 120mm/4.72"
Capacidad Fluida ............................................................ 12.8 oz.
Cumple con las Normas de Seguridad/ASME PASE-2019
KTI-XD63703
www.ktoolinternational.com

10
KTI-XD63703 rev. 03/12/21
Este símbolo indica una alerta de seguridad y se usa para
advertir sobre peligro de accidentes personales. Observe toda
la información de seguridad que sigue a este símbolo para
evitar la posibilidad de que ocurran lesiones o muerte.
IMPORTANTE: LEA ESTAS INSTRUCCIONES ANTES DE USAR EL DISPOSITIVO
ANTES DE USAR ESTE DISPOSITIVO, LEA ESTE MANUAL DETENIDAMENTE. PROCURE ENTENDER SUS PROCEDIMIENTOS OPERATIVOS,
ADVERTENCIAS DE SEGURIDAD Y FORMA DE MANTENIMIENTO.
El propietario es responsable de asegurarse de que todo el personal lea este manual antes de usar el dispositivo. Asimismo, es responsabilidad del
propietario mantener este manual en buenas condiciones en una ubicación conveniente para su consulta. Si las etiquetas del manual o producto son
ilegibles o no están en su lugar, deberá ponerse en contacto con K-Tool Internatinoal para obtenerlas gratis. El comprador/propietario o una persona
designada deberá leer y comentar el producto y las advertencias de seguridad en la lengua materna del operario que no hable inglés fluido, a fin de
asegurarse de que comprende el contenido.
NATURALEZA DE LAS SITUACIONES DE RIESGO
El uso de los conjuntos de potencia hidráulica portátiles está sujeto a ciertos peligros los que no se pueden prevenir por medidas mecánicas, sino sólo
por ejercer la inteligencia, cuidado y sentido común. La versatilidad del uso está limitada sólo por la imaginación y la ingeniosidad de su operador; por
ende, K Tool International no podrá responsabilizarse por los daños al producto o lesiones personales debido al juicio incorrecto del operador o al uso
inadecuado del equipo. Es imprescindible contar con personal involucrado en el uso y la operación del equipo quienes sean cuidadosos, competentes,
entrenados y calificados en la operación segura del equipo y su uso adecuado al momento de trabajar sobre los armazones del vehículo y las partes del
cuerpo. Ejemplos de los peligros son las caídas o el deslizamiento de la carga, ocasionados por la sujeción inadecuada de las cargas, la sobrecarga, las
cargas no centradas y los montajes inadecuados. Los peligros adicionales se podrán ocasionar por la rotura o explosión de las mangueras hidráulicas y
acoplamientos relacionados. debido al uso, mal uso, el montaje inadecuado y además usar el equipo para algún uso para el cual no fue destinado.
FORMAS DE EVITAR LAS SITUACIONES DE RIESGO
• Estudie, comprenda y siga todas las instrucciones antes de operar este dispositivo.
 • ElpropietariodelkitesresponsabledequeelkitseusedeacuerdoconlasnormasdeseguridadOSHA,estatalesylocales.
 • ElusuarioylostranseúntesdebenusarprotecciónparalosojosquecumplaconANSIZ87.1ylasnormasdeOSHA.
• No use más allá de la capacidad nominal.
 • Cuandoseusanaccesoriosyadaptadoresconelkit,lacapacidadnominaldelkitnodebesermayorquelacapacidadnominaldel
  componentedemenorcalicaciónolacombinacióndecomponentesquecomponeelkit.ConsultelaseccióndelManualdel
propietario titulada “APLICACIÓN DE FUERZA” para aplicaciones típicas y capacidades de carga correspondientes.
 • Useunmanómetroqueindiquelafuerzaaplicada.
• Elpistóndelesparcidorcuentaconunaclasicaciónnominalde1/2toneladas
 • Lascabezasdegomatienenunacapacidadnominalde1/2toneladaenelkitde4toneladasyunacapacidadde1toneladaenelkit
de 10 toneladas.
• No sobre extienda los carneros.
 • Cuandousetubosdeextensión,coloqueeltubomáscortomásalejadodelcilindro.
 • Losaccesoriosylostubosdeextensióndebenestaralineadosycompletamenteenganchadosparaquelafuerzadelpistónsea
recta y evite las condiciones descentradas.
 • Antesdeoperar,aprietetodaslasconexionesdemanguera,manómetroycolectorparaqueesténsegurasylibresdefugas.No
apriete demasiado o puede causar una falla prematura del hilo o accesorios de presión dividida. Apriete todas las conexiones de
desconexión rápida de la manguera con la mano solamente.
 • Nosometalamangueraacalorextremoofrío,superciesaladas,abrasión,impacto,retorcimiento,torsión,curvatura,exióno
  cualquiercondiciónquerestrinjaoafecteelujodeuido.
 • Asegúresedequelaconguraciónseaestableyseguraantesderealizarcualquiertrabajo.
• Utilice este kit para el propósito previsto de la reparación del cuerpo / bastidor del vehículo únicamente.
• Solo los componentes suministrados con este kit deben usarse con este kit.
 • Nosedebenhaceralteracionesomodicacionesaningunodeloscomponentesdelkit.
• El incumplimiento de estas advertencias puede ocasionar lesiones personales graves o fatales y / o daños a la propiedad.
ADVERTENCIA: Esteproductolepodráexponeraciertosquímicos,paraincluirelníquel,conocidosenelEstadodeCaliforniapor
ocasionarcáncerydefectoscongénitosuotrosdañosalareproducción.Paramayoresinformes,visite:www.P65Warnings.ca.gov.
CONSECUENCIAS DE NO PREVENIR LAS SITUACIONES DE RIESGO
No leer, comprender u observar todo el contenido de este manual en relación con sus INSTRUCCIONES DE USO, ADVERTENCIAS DE SEGURIDAD y
FORMA DE MANTENIMIENTO, así como desatender las FORMAS DE EVITAR LAS SITUACIONES DE RIESGO, puede provocar accidentes que tengan
como consecuencia lesiones graves, peligro de muerte o daños materiales.
ADVERTENCIA: Indica una situación
peligrosa que si no se evita, puede
provocar la muerte o lesiones graves.
INFORMACIÓN DE ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA
ADVERTENCIA