MENUS:
Press SET button on the ma n screen to access the menus. If the
lock funct on s deact vated, PROG menu appears on the screen. Use
the d rect on buttons to see ADJUST,DISPLY and EXIT
MANUAL MODE
Manual mode s used for sett ng or test ng the des red relay output, or
deact vat ng the program operat on. Th s mode could be act vated for
both of the relays separately. If output A s locked t can't be sw tched
to manual mode for output A, but t can be sw tched for output B.
For block ng the act vat on of manual mode, the related output should
be locked. Lock funct on s descr bed on page 7.
There are two d fferent manual modes.
1-TEMPORARY MODE : When the subsequent program steps n,
temporary manual mode would be deact vated.
Temporary manual mode for Relay A :
Push ▼ button unt l the flash ng hand con appears on the left of the
screen.
Throughout the manual mode, for chang ng Relay A output, t s
necessary to push and release ▼ button.
In th s mode, f the subsequent program for Relay A changes the
output, manual mode would be deact vated automat cally and
ASTRO operates the program. Otherw se manual mode would
cont nue to be act ve for Relay A.
To deact vate th s mode for Relay A as an opt on, push ▼ button unt l
the flash ng hand con d sappears.
Temporary manual mode for Relay B :
Push ▲ button unt l the flash ng hand con appears on the r ght of the
screen.
Throughout the manual mode, for chang ng Relay B output, t s
necessary to push and release ▲ button.
In th s mode, f the subsequent program for Relay B changes the
output, manual mode would be deact vated automat cally and
ASTRO operates the program. Otherw se manual mode would
cont nue to be act ve for Relay B.
To deact vate th s mode for Relay B as an opt on, push ▲ button
unt l the flash ng hand con d sappears.
- PERMANENT MODE : It s only poss ble to deact vate permanent
mode as manually.
Permanent manual mode for Relay A:
Push ▼ and SET buttons at the same t me unt l the hand con
appears on the left of the screen.
Permanent manual mode s not deact vated automat cally. The only
way to deact vate th s mode s manually.
Throughout the manual mode, for chang ng Relay A output, t s
necessary to push and release ▼ button.
To deact vate th s mode for Relay A, push ▼ button unt l the hand
con d sappears.
Permanent manual mode for Relay B:
Push ▲ and SET buttons at the same t me unt l the hand con
appears on the r ght of the screen.
Permanent manual mode s not deact vated automat cally. The only
way to deact vate th s mode s manually.
Throughout the manual mode, for chang ng Relay B output, t s
necessary to push and release ▲ button.
To deact vate th s mode for Relay B, push ▲ button unt l the hand
con d sappears.
PROGRAM:
All program sett ngs could be done.
Creat ng new program, chang ng or
delet ng an ex st ng program.
ADJUST:
Dev ce sett ngs could be done.
information :
In th s menu, program and dev ce
sett ngs could be mon tored w thout
mak ng changes. Use the d rect on
buttons to see nformat on about sunr se,
sunset, programs, memory status,
season (summer-w nter), lat tude,
long tude,qu et mode status.
PROGRAM MENU:
Press SET button on PROG screen to
access the Program Menu. Use the d rect on
buttons to see NEW,CHANGE,DELETE and
EXIT menus.
NEW : New programs are created.
CHANGE : Ex st ng programs could be
changed.
DELETE : Ex st ng programs could be
deleted. It s poss ble to delete all
of them or the selected one.
SET
▲
▲
▲
SET
▲
▲
▲
SET
SET
▲
▲
▲
▲
▲
▲
▲
▲
SET
ADJUST MENU:
In th s menu, dev ce sett ngs could be done.
Real T me Clock and Calender could be set
n TIME menu
In th s menu, dayl ght sav ng t me sett ngs
could be done. If AUTO s chosen, dev ce
determ nes beg nn ng dates of the summer
and w nter automat cally.
Coord nates and t me zone sett ngs of the
locat on could be done n th s menu.
Lock funct on could be act vated to prevent
unauthor zed persons from us ng the dev ce.
Th s mode could be act vated for both of the
relays separately.
Qu et mode could be act vated to stop the
program operat on for a certa n per od.
In th s menu, PIN code could be changed.
PIN code s a 4 d g t number.
Infrared (con03) commun cat on could be
Enabled or d sabled
Language could be changed to turk sh or
engl sh
All dev ce sett ngs except t me and date are
set to default.
The dev ce could be restarted t me and date
Sett ngs would be cleared.
www.kael.com.tr
ınfo
prog
adjust
back
ınfra
Langua
defaul
reset
▲
▲
back
back
