Kallista Inigo P7430 User manual

INSTALLATION INSTRUCTIONS
Inigo Console Table
1095725-2-A
Page 1 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P74300, P74301

INSTALLATION INSTRUCTIONS
Inigo Console Table
1095725-2-A
Page 2 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual
before you install your Kallista product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
BeFORe YOU BeGIN
Observe all local building codes.
Prior to installation, unpack the new lavatory and console and inspect them for damage. Return the lavatory
and console to their protective cartons until you are ready to install them.
These instructions are for installing the console table to wood frame construction. For other installations,
supply suitable bracing and fastening devices of sufcient size and strength.
Sufcient support behind the nished wall, such as 2x6 wall bracing, is required for proper installation. 
This installation is designed to be done with a minimum of two people. Do not install this xture alone. 
All dimensions given assume that the oor and walls are square, plumb, and level. Make appropriate ad-
justments for other conditions.
Kallista reserves the right to make revisions in the design of products without notice, as specied in the 
Price Book.
TOOLS ANd MATeRIALS
Tape
Measure
Assorted
Screwdrivers
Adjustable
Wrench
Socket Wrench
W/Sockets
Drill
Pencil Level
Silicone
Sealant

INSTALLATION INSTRUCTIONS
Inigo Console Table
1095725-2-A
Page 3 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
PRePARe THe SITe1.
Finished
Floor
Wall Bracing
(2x6 minimum)
C
L
Finished
Wall
Mark the
anchor
holes.
Side Rail
Bracket Anchor
Holes
Console Table
Bracket Anchor
Holes
Foot
Anchor
Holes
21-1/4” 16” C
L
26-23/32”
31-13/16”
31-1/2”
32-13/16”
34”
Rough-in the water supply lines and the drain piping.
Install a minimum of a 2x6 as a wall brace to provide support for 
the wall bracket. The brace should be the same length as the
console table, 36″ and should be positioned 32″ from the nished
oor to the top edge of the board. The center of the wall brace
should be in-line with the drain outlet.
Finish the wall.
Mark the centerline on the oor and the wall.
Mark the anchor holes on the wall for the side rail mounting 
brackets.
Mark the anchor holes for the console table mounting bracket on 
the wall by holding the bracket up to the nished wall so that the
center of the bracket lines up with the centerline. Mark the loca-
tion of the anchor holes with a pencil.
Mark the location of the holes on the oor for the feet anchors.
Drill two holes 5/16″ D. x 1/2″ deep, in the nished oor for each 
foot anchor. The holes should be 21-1/4” from the wall and 16”
from the centerline.
INSTALL THe MOUNTING BRACKeTS2.
Console Table
Mounting Bracket
Side Rail
Mounting Bracket
Install the side rail mounting brackets to the nished wall 
with fasteners suitable for your wall type.
Install the console table mounting bracket to the nished 
wall with fasteners suitable for your wall type.
Verify the table mounting bracket is level.

INSTALLATION INSTRUCTIONS
Inigo Console Table
1095725-2-A
Page 4 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
ASSeMBLe THe CONSOLe TABLe LeGS3.
Front Towel
Bars
Side Rails
Side Rail
Mounting Bracket
Leg Height
Adjustment Pad
Leg Height
Adjustment Pad
Insert the front towel bars into the holes in the legs,
being sure to engage the towel bars in the O-rings in
the legs.
Insert legs into holes in oor.
Tilt the legs away from the wall so that a helper can
install the side rails into the legs, being sure to engage
the side rails in the O-rings in the legs.
Tilt the legs back to a vertical position, while a helper
guides the side rails into the side rail mounting brack-
ets, being sure to engage the side rails in the O-rings in
the side rail mounting brackets.
Adjust the leg height adjustment pads so that the top of
the legs are level with each other.
INSTALL THe CONSOLe TOP4.
Apply silicone
sealant
Place the console top upside down to install the lavatory.
NOTe: When installing the lavatory, use the clips provided with the lavatory
and the hardware provided with the console top.
Install the lavatory.
With a partner, pick up the console top and align the holes on the bot-
tom of the console top with the holes on the top of the wall bracket.
Verify that the console top is level and re-adjust the height adjustment
pads if necessary.
Apply silicone sealant where the leg height adjustment pads meet the
console top to stabilize it.
Thread the supplied washer and Phillips head screw through the
bracket into the console top and secure. Do not overtighten.

INSTALLATION INSTRUCTIONS
Inigo Console Table
1095725-2-A
Page 5 of 5
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Three faucet holes have been partially drilled from the underside of the console top.
On the top, show surface, of the console top, locate the center of the required faucet holes. Using a com-
pass or circle template, draw a circle for the required holes.
Using a small hammer, create the faucet hole(s) by gently tapping the console top within the circles until
the stone breaks away.
NOTe: dO NOT strike the console top with too much force. dO NOT strike from the bottom side of the console
top. This will damage the top surface of the console top.
Using a le or sanding cylinder, complete the removal of stone material to create a clean round hole.
Backsplash Console
Top
Attach backsplash to console table and wall with clear silicone.
Connect the water supply and check for leaks.
STONe TOP HOLe FABRICATION (OPTIONAL)5.
COMPLeTe THe INSTALLATION6.