Kallista Vir Stil .75 User manual

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
1 of 8
P74205, P74209, P74202-SM P74210, P74211, P74212 P74213, P74214, P74215

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
2 of 8
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page or visit us on line at kallista.com.
BEFORE YOU BEGIN
The Vir Stil® .75 Vanity consists of the following:
●P74205 – .75 Wood Vanity ●P74202-SM – Small Metal Base with (1 ea.) Handle
●P74209 – Stone Top ●P72040 – Undercounter Basin
The Vir Stil® 1.0 Vanity consists of the following:
●P74210 – 1.0 Wood Vanity ●P74212 – Metal Base with (4 ea.) Handles
●P74211 – Stone Top ●P72040 – Undercounter Basin
The Vir Stil® 1.5 Vanity consists of the following:
●P74213 – 1.5 Wood Vanity ●P74215 – Large Metal Base with (5 ea.) Handles
●P74214 – Large Stone Top ●P72040 – Undercounter Basin
Prior to installation, unpack all products and inspect them for damage. If the product is damaged, contact
Kallista’s Customer Service immediately at the phone number listed at the bottom of the page.
NOTE: Although your vanity may differ from the one shown in the illustrations, the installation steps are the
same.
This installation requires a minimum of two people. Do not install this xture alone.
The stone console lavatory can be installed with three different faucet congurations:
●Single-Hole for a monoblock faucet
●Three-Hole for a widespread faucet
●No-Hole for a wall-mount faucet
Refer to your faucet installation instructions to determine which conguration is necessary for your lavatory.
To create the holes necessary for your faucet installation, refer to the instructions in section 2.
KALLISTA reserves the right to make revisions in the design of products without notice, as specied in the
Price Book.

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
3 of 8
TOOLS AND MATERIALS
Rags
Pliers File
Phillips ScrewdriverCompass
Hammer
Level
1. ATTACH VANITY TO METAL BASE
Flat Head
Cap Screws
Vir Stil
Vanity Base
Flat Head
Cap Screws
Vir Stil 1.5
Vanity Base
Base Foot
Base Foot
Leveler
Wood
Screws
Assemble the metal base.
Position the metal base in the desired nal location. If the oor is uneven, use a pair of pliers to adjust the
leveler located in the foot of the base.
NOTE: Lowering the vanity into place is a two person task.
Mount the vanity to the metal base using the supplied wood screws.

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
4 of 8
2. STONE TOP HOLE FABRICATION
Partially Drilled Hole
Top or Finished Surface
Underside
2"
(51 mm)
4"
(102 mm)
4"
(102 mm)
6-5/16"
(160 mm)
Top or
Finished Surface
File
NOTE: Three faucet holes have been partially drilled from the underside of the stone top.
Determine the number of faucet holes needed for your installation.
Turn the stone top upright.
On the top or nished surface of the stone, locate the center for each faucet hole that will be used.
NOTE: The circles should align with the partially drilled holes on the underside of the stone top.
Use a compass or circle template to draw a circle representing the holes.
IMPORTANT! Striking the stone with too much force or from the underside will damage the top or nished
surface of the stone.
Using a small hammer, create the faucet hole(s) by gently tapping the stone within the circles until the
stone breaks away.
Using a le or sanding cylinder, complete the removal of stone material to create a clean, round hole.

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
5 of 8
3. COMPLETE INSTALLATION
Stone Top
NOTE: Prior to positioning the stone top on the vanity, it is recommended that the plumber install the faucet and
undercounter basin.
With assistance from a second person, gently lower the stone top onto the vanity.
NOTE: Only three drops of adhesive are required.
Prior to mounting the handle to the door, place a small amount of adhesive to the threading of the handles.
Screw the handles together with the male threads on the exterior side.
Using a damp rag, wipe away any excess adhesive immediately.

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
6 of 8
4. ADJUST THE CLOSING SPEED OF THE DOOR
Adjustment Screw
Adapter
Piston
Clip
Installation:
Loosen a screw on the mounting plate and position the adapter under the screw.
Tighten the screw to secure the adapter to the mounting plate.
To attach the piston, insert the clips on the piston into the square holes on the adapter. Slide the piston back
until it snaps into place.
Adjustment:
To decrease the closing speed, turn the adjustment screw toward the plus sign.
To increase the closing speed, turn the adjustment screw toward the minus sign.

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
7 of 8
5. REMOVE/ADJUST THE DOORS AND HINGES
Vertical
Gap
Horizontal
Side of Vanity
Top of Door
Hinge Base
Latch
Bracket
Slot
Hinge Cup
Removal:
At each hinge assembly location on the door, hold the door in place with one hand while releasing the latch
from the bracket. The door will detach from the hinges. Set the door aside.
If applicable, remove the remaining door in the same manner.
Replacement/Reinstallation:
Line up the latch pin on the hinge cup with the groove on the hinge base and then snap into place.
Open and close the door to conrm smooth operation. Adjust the screws on the hinge assembly as needed.
Adjustment:
NOTE: Refer to the hinge assembly illustration above to select the screw that corresponds to the adjustment
needed.
Vertical (up or down) – Turn the screw either way on the bottom and top hinge assembly until the desired
adjustment is achieved.
Horizontal (left or right) – Turn the screw either way on the bottom and top hinge assembly until the
desired adjustment is achieved.
Gap (in or out) – Loosen the screw on the bottom and top hinge assembly, hold the door in the desired
position, and then retighten the screws.

INSTALLATION INSTRUCTIONS
Vanity
1207801-2-B
© 2013 KALLISTA
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
8 of 8
6. REMOVE/ADJUST THE DRAWER
Rail
Tab
Underside View
Release Latch
Drawer Height
Adjustment Wheel
NOTE: A drawer height adjustment wheel and a release latch are located underneath the front of the drawer at
each corner.
Removal:
Slide the drawer out on the rails until fully extended.
Pull both release latches toward you and then pull the front of the drawer up off the rails.
Lift the drawer out from the vanity.
Reinstallion:
Fully extend the rails.
Align the grooves on the underside of the drawer with the rails and set the drawer into place.
Hold the drawer in place on the rails with one hand. With your other hand, pull the tab on the bottom front of
the rail toward you until you hear the rail “snap” into place. Repeat this step for the remaining rail.
Ensure the drawer is locked into place by lightly lifting the front of the drawer upward. If the drawer does not
lift up, it is engaged. If the drawer lifts up, repeat the procedure.
Slide the drawer in and out of the vanity to ensure smooth operation.
Adjustment
Slide the drawer out on the rails until fully extended.
Turn the drawer height adjustment wheels to adjust the drawer height. To lower the drawer, turn the wheel on
the left side of the drawer clockwise and/or the wheel on the right side of the drawer counterclockwise. Turn
the wheel(s) in the opposite direction to raise the drawer.