Kallista P73015 User manual

INSTALLATION INSTRUCTIONS
Original For Him Dressing Table
1008300_2_A
1 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P73015, P73032

INSTALLATION INSTRUCTIONS
Original For Him Dressing Table
1008300_2_A
2 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual
before you install your Kallista product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
BefORe yOU BegIN
These instructions are for installing the dressing table (P73015) and pre-cut marble top (P73032).
Observe all local plumbing and building codes.
Prior to installation, unpack the new dressing table and marble top and inspect them for damage. Return
the dressing table and marble top to their protective cartons until you are ready to install them.
Refer to the dressing table specication sheet for P-trap and supply location recommendations. Verify your
supply valves and P-trap will not interfere with the shelf and drawer. Install the water supply and drain lines.
The water supply nipples must extend 3″ (76 mm) beyond the nished wall material.
These instructions are for installing the dressing table to wood frame construction. For other installations,
supply suitable bracing and fastening devices of sufcient size and strength.
Provide 2x6 backing material in the nished wall. The height from the top of the 2x6 backing material to the
oor must be 36-1/4″ (921 mm).
This installation is recommended to be done with a minimum of two people.
The marble top can be installed with three different faucet congurations:
● ″Single-Hole″ for a monoblock faucet
● ″Three-Hole″ for a widespread faucet
● ″No-Hole″ for a wall-mount faucet
All dimensions given assume that the oor and walls are square, plumb, and level. Make appropriate
adjustments for other conditions.
Remove any moldings that may inhibit the dressing table from being ush against the nished wall.
Make sure the path of the shelf will not be obstructed as it slides open.
Kallista reserves the right to make revisions in the design of products without notice, as specied in the
Price Book.

ThANk yOU fOR ChOOSINg kALLISTA
TOOLS ANd MATeRIALS
Pencil
Tape
Measure Level Drill
Hex
Wrench
Clear 100% Silicone
Sealant or Caulk
File
Hammer
Safety Glasses
Plus
● Conventional woodworking
tools and materials, as
appropriate
● Hole Saw
● Wood Screws
● Screwdriver

INSTALLATION INSTRUCTIONS
Original For Him Dressing Table
1008300_2_A
3 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
1. INSTALL The dReSSINg TABLe
Measure and mark 36-1/4″ (921 mm) up from the oor. This will
be the height from the top of the 2x6 backing material to the
oor.
Secure the 2x6 backing material to the studs with framing nails.
Install the water supply and drain lines. The water supply
nipples must extend at least 3″ (76 mm) beyond the nished
wall material.
Complete the nished wall. Make sure that the nished wall is
straight and plumb, and that the oor is at and perpendicular
to the nished wall.
IMPORTANT! Do not install any moldings that may inhibit the
dressing table from being plumb against the nished wall.
Position the dressing table against the nished wall.
Verify the dressing table is level front to back and side to side. If necessary,
adjust the levelers on the bottom of the dressing table.
Mark the supply and drain locations on the inside of the dressing table back
wall. Move the dressing table away from the wall.
Cut the marked supply and drain locations from inside of the dressing table
using a hole saw.
Position the dressing table against the wall, aligning the supply and drain
locations with the cut holes on the dressing table back wall.
2. TeST fIT The dReSSINg TABLe
36-1/4”
(92.1 cm)
2x6 Backing Material

INSTALLATION INSTRUCTIONS
Original For Him Dressing Table
1008300_2_A
4 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].

Three faucet holes have been partially drilled from the underside of the console top.
On the top, show surface, of the marble top, locate the center of the required faucet holes. Using a
compass or circle template, draw a circle for the required holes.
Using a small hammer, create the faucet hole(s) by gently tapping the console top within the circles until the
marble breaks away.
NOTE: DO NOT strike the console top with too much force. DO NOT strike from the bottom side of the
console top. This will damage the top surface of the console top.
Using a le or sanding cylinder, complete the removal of marble material to create a clean round hole.
3. MARBLe TOP hOLe fABRICATION (OPTIONAL)
20-3/16" (513 mm)
4"(102 mm)
8"(203 mm)
2-1/2"(64 mm)

INSTALLATION INSTRUCTIONS
Original For Him Dressing Table
1008300_2_A
5 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].

NOTE: If using a lavatory with overow, ensure that the
lavatory is installed with the overow to the front of the marble
top and dressing table.
Install the lavatory and faucet to the marble top at this
time. Refer to the lavatory manufacturer’s instructions
for proper lavatory installation. Refer to the faucet
manufacturer’s instructions for proper faucet installation.
With the help of an assistant, place the marble top on top
of the dressing table. Verify correct t and alignment of all
components. Adjust as necessary.
With the help of an assistant, carefully remove the marble
top and set aside.
Drill two pilot holes through the mounting rail and nished
wall on each side of the dressing table. Make sure the two
pilot holes are spaced a minimum of 16″ (406 mm) apart
from one another.
Tighten a wood screw through each of the two drilled
holes until the dressing table is ush and secure against
the nished wall.
Apply clear 100% silicone caulk or sealant to the top of the dressing table.
With the help of an assistant, replace the marble top on top of the dressing table. Verify correct t and
alignment. Adjust as necessary.

Install the P-trap according to the manufacturer’s instructions.
Connect the water supply and check all connections for leaks. Repair as needed.
4. INSTALL The MARBLe TOP
5. COMPLeTe The INSTALLATION

INSTALLATION INSTRUCTIONS
Original For Him Dressing Table
1008300_2_A
6 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].

Drawer Height
Adjustment Wheel Release Latch
Underside View
Rail Tab
To remove the drawer:
Slide the drawer out on the rails until fully extended.
Pull both release latches toward you, then pull the front of the drawer up off the rails.
Lift the drawer out from the dressing table.
To reinstall the drawer:
Fully extend the rails.
Align the grooves on the underside of the drawer with the rails and set into place.
Hold the drawer in place on the rails with one hand. With your other hand, pull the tab on the bottom front of
the rail toward you until you hear the rail ″snap″ into place. Repeat this step for the remaining rail.
Ensure the drawer is locked into place by lightly lifting the front of the drawer upward. If the drawer does not
lift up, it is engaged. If the drawer lifts up, repeat the above procedure.
Slide the drawer in and out of the dressing table to ensure smooth operation.
Adjustment:
Slide the drawer out on the rails until fully extended.
Turn the drawer height adjustment wheels to adjust the drawer height. To lower the drawer, turn the wheel
on the left side of the drawer clockwise and/or the wheel on the right side of the drawer counterclockwise.
Turn the wheel(s) in the opposite direction to raise the drawer.
6. ReMOve/AdjUST The dRAweRS