Kallista P23065 User manual

INSTALLATION INSTRUCTIONS
Pulldown Kitchen Faucet
1072005-2-B
Page 1 of 4
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P23071P23065

INSTALLATION INSTRUCTIONS
Pulldown Kitchen Faucet
1072005-2-B
Page 2 of 4
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual
before you install your Kallista product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
BEFORE YOU BEGIN
CAUTION: Risk of fresh water contamination. This faucet contains important back-siphonage
protection. Do not replace the faucet ground joints or remove any components.
Observe all local plumbing and building codes.
Shut off the water supplies.
Carefully inspect waste and supply tubing for any sign of damage and replace if necessary.
For new installations, assemble the faucet on the sink before installing the sink.
Except for plumbers putty, do not use petroleum based products on this faucet.
Before installation, unpack the new faucet and inspect it for damage. Return the faucet to the carton until
you are ready to install it.
Kallista Co. reserves right to make revisions in the design of faucets without notice, as specied in the 
Price Book.
TOOLS AND MATERIALS
Hex
Wrench
Phillips�
Screwdriver
Adjustable
Wrench
Two 3/8” Male�
Supply Connections
Plumbers
Putty
1. FAUCET INSTALLATION
Ring
Screw
Metal Washer
Fiber Washer
Sink
Faucet
Supply Hose
Shank
Ensure that O-ring is installed in bottom of escutcheon.
Partially thread the two screws into the threaded ring until
the screws barely protrude from the backside of the thread-
ed ring.
Fit the faucet through the hole in the sink. Position the fau-
cet so the handle faces in the desired position. The recom-
mended handle position is to the user’s right.
Turn the ring so the screws are to the front and back.
Use a Phillips screwdriver to tighten the screws securely
and evenly.

INSTALLATION INSTRUCTIONS
Pulldown Kitchen Faucet
1072005-2-B
Page 3 of 4
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
2. SUPPLY INSTALLATION
3" (7.6 cm)
or Larger
Cold
Cold
Hot
CAUTION: Risk of restricted water ow and product dam-
age. Use extreme care when bending the supply hoses to avoid
kinking and twisting. Hoses must not be taut after installation.
NOTE: If the sink is not installed, install it at this time. Be sure to fol-
low all instructions packed with the sink.
NOTE: If the sink installation requires that you coil the supply hoses to
obtain a good connection, maintain an inside coil diameter of at least 3”
(7.6 cm).
NOTE: The most common type of faucet installation is with the handle
positioned to the right. Pull the handle for cold water or push the
handle for hot water. If the handle is installed to the left or centered,
reverse the supply tubes; connect the tube for cold water to the hot
supply and the tube for hot water to the cold supply. This will maintain
the relationship of pulling the handle for cold water or pushing for hot
water. If the handle is centered, press it to the right for cold water or to
the left for hot water.
Position the hot and cold water supplies to not interfere with other
hoses.
Connect the supply hoses to the supply stops. Left is hot, right is
cold.
Tighten all connections
3. FLUSH THE SUPPLY LINES
Valve Outlet Hose
Place the valve outlet hose into a bucket or suitable container.
Turn on the hot and cold supplies.
Turn the faucet handle to the full cold ON position.
Let the water run for one minute to remove any debris.
Rotate the faucet handle to full hot position.
Let the water run for one minute to remove any debris.
Turn the faucet handle to the OFF position.

INSTALLATION INSTRUCTIONS
Pulldown Kitchen Faucet
1072005-2-B
Page 4 of 4
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
Valve Outlet Hose
O-ring
Spray Hose
Weight
Slide the weight onto the spray hose.
Verify that the hose ends are clean and that the O-ring is in place.
Fully engage the hose ends.
Reposition the supply hoses if necessary.
Extend and retract the spray hose to check for smooth operation.
4. CONNECT THE SPRAY HOSE