Kallista P21586 User manual

INSTALLATION INSTRUCTIONS
Kallista Bath Flip Drain
1117993_2_A
Page 1 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P21586

INSTALLATION INSTRUCTIONS
Kallista Bath Flip Drain
1117993_2_A
Page 2 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual
before you install your Kallista product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
TOOLS
Plumbers
Putty
Adjustable
Wrench
Caulk
Gun
Tape
Measure
Silicone
Sealant
Level
P-Trap Keyhole or Saber Saw Hacksaw Pliers With Rubber Grips
BEFORE YOU BEGIN
Observe all local plumbing and building codes.
Turn off the main water supplies.
Refer to the roughing-in dimensions of your bath to properly install this product.
Carefully inspect the ttings for damage before installing.
Install the drain before installing the bath.
Kallista reserves the right to make revisions in the design of products without notice, as specied in the 
Price Book.

INSTALLATION INSTRUCTIONS
Kallista Bath Flip Drain
1117993_2_A
Page 3 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
ROUGH-IN DIAGRAM
Optional Tee
(Included)
1-3/16”
(3 cm)
1-15/16”
(5 cm)
1-3/16”
(3 cm) Max
3-15/16”
(10 cm)
17-5/16”
(44 cm)
Max 1-7/8”
(4.8 cm) Max
2-13/16”
(7.2 cm)
9-1/2”
(24.2 cm)
Max
19-5/16”
(49 cm)
Max
3-7/16”
(8.8 cm)
Max
3-7/16”
(8.8 cm)
Max
4-1/4”
(10.8 cm)
6-1/4”
(16 cm)
Max
2-5/16”
(5.8 cm)
9-1/2”
(24.2 cm)
Max
3-1/8”
(8 cm)
2-3/16”
(5.6 cm) Max
1-9/16”
(3.9 cm)
2-1/2”
(6.4 cm)

INSTALLATION INSTRUCTIONS
Kallista Bath Flip Drain
1117993_2_A
Page 4 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INITIAL ASSEMBLY
Drain
Elbow
Compression
Seals
Tee
Coupling Nut
Compression Ring
Compression Seal
Overflow Elbow
Overflow Pipe
Drain Pipe
Tailpiece
Compression Ring
Coupling Nut
Compression Ring
Coupling Nut
If using tee with compression joints:
Remove the overow body, waste body, tailpiece and tee from the 
packaging.
Disassemble the coupling nuts, compression rings, and compression
seals from the tee.
Assemble the drain elbow, drain pipe, tee, tailpiece, overow pipe and 
overow elbow. Test t the assembly to the bathtub.
If necessary, mark and cut the drain pipe and overow pipe, using the 
dimensions in the rough-in diagram and the rough-in information for
the tub as a guide.
Remove any sharp edges and retest t to bathtub.
Disassemble the drain elbow, drain pipe, tee, tailpiece, overow pipe 
and overow elbow.
Slide a coupling nut, compression ring, and compression seal onto the
overow pipe. Repeat this process on the drain pipe and tailpiece.
Fit the overow pipe, tailpiece, and drain pipe into the tee.
Hand tighten the coupling nuts onto the tee allowing movement of the
overow body, drain body, and tailpiece.
Do not fully tighten the coupling nuts until instructed to do so.
If using tee with soldered joints:
Drain Elbow
Tee
Overflow Elbow
Overflow Pipe
Drain Pipe
Tailpiece
Assemble the drain elbow, drain pipe, tee, tailpiece, overow pipe and 
overow elbow. Test t the assembly to the bathtub.
If necessary, mark and cut the drain pipe and overow pipe, using the 
dimensions in the rough-in diagram and the rough-in information for
the tub as a guide.
Remove any sharp edges and retest t to bathtub.
Do not solder the joints until instructed to do so.

INSTALLATION INSTRUCTIONS
Kallista Bath Flip Drain
1117993_2_A
Page 5 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
FIT THE WASTE AND OVERFLOW TO THE TUB
Lower Drain Gasket
Upper Drain Gasket
Drain Trim
Drain Outlet
Drain Elbow
Overflow Elbow
Overflow Outlet
Backplate
Bolt
Place the lower drain gasket on top of the drain elbow.
Set the upper drain gasket on top of the drain outlet.
Insert the drain trim through the drain outlet and thread into the drain elbow.
Hand tighten the drain trim into the drain elbow. Do not wrench tighten at this time.
Align the overow elbow to the outside of the overow outlet.
Insert the bolt through the backplate.
Insert the bolt with the backplate onto the threaded cylinder of the overow elbow.
Turn the bolt clockwise until hand-tight to secure the bolt with the backplate to the threaded cylinder. Do not
wrench tighten at this time.
Verify the drain’s t to the tub. Adjust as necessary.
Secure the Connections and Fittings
Wrench tighten the compression ttings to one quarter turn past hand-tight.
If using soldered connections, solder all joints at the tee.
Remove Waste and Overow from Tub
Remove the drain trim, upper drain gasket and lower drain gasket from the drain elbow.
Remove the bolt and backplate from the overow elbow.
Remove the drain assembly from the tub and loosely install tailpiece into the P-trap.

INSTALLATION INSTRUCTIONS
Kallista Bath Flip Drain
1117993_2_A
Page 6 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALL THE WASTE AND OVERFLOW
Lower Drain Gasket
Upper Drain Gasket
Drain Trim
Drain Outlet
Drain Elbow
Overflow Elbow
Overflow Outlet
Backplate
Bolt
Overflow Hood
CAUTION: Risk of property damage. Make sure a watertight seal exists on all bath drain connections.
With the waste and overow assembly installed loosely in the P-trap, install the tub according to the 
manufacturer’s instructions.
Apply silicone sealant to the underside of the lower drain gasket, then place the drain gasket on top of the
drain elbow.
Set the upper drain gasket on top of the drain outlet.
Apply plumbers putty to the underside of the drain trim ange.
Insert the drain trim through the drain outlet and thread into the drain elbow.
Hand tighten the drain trim into the drain elbow. Do not wrench tighten at this time.
Apply plumbers putty or other sealant to the front edge of the overow elbow according to the putty 
manufacturer’s instructions.
Align the overow elbow to the outside of the overow outlet.
Insert the bolt through the backplate.
Insert the bolt with the backplate onto the threaded cylinder of the overow elbow.
Turn the bolt clockwise until hand-tight to secure the bolt with the backplate to the threaded cylinder. Do not
wrench tighten at this time.
Verify the drain’s t to the tub. Adjust as necessary

INSTALLATION INSTRUCTIONS
Kallista Bath Flip Drain
1117993_2_A
Page 7 of 7
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALL THE WASTE AND OVERFLOW (CONT’D)
Secure the Tailpiece into the P-trap
Wrench tighten the P-trap compression tting to one quarter turn past hand-tight.
If using soldered connections, solder the joint at the P-trap.
Secure the Drain Trim
Open the ip drain and insert the grips of a rubber coated pliers into the drain trim and turn to tighten. Be 
careful not to scratch the nish.
Install the Overow Hood
Secure the backplate to the tub by tightening the bolt to one quarter turn past hand-tight.
Thread the overow hood into the bolt.
COMPLETE THE INSTALLATION
Complete the Bath Installation
Check all drain connections for leaks and repair as needed.
Install the bath faucet according to the bath faucet manufacturer’s installation guide.
Refer to the bath manufacturer’s installation guide to complete the nished deck or wall around the bath.