Kallista P21581 User manual

INSTALLATION INSTRUCTIONS
Cable Drain & Cable Drain Trim Kit
1096756_2_A
1 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P21581 &
P21582

INSTALLATION INSTRUCTIONS
Cable Drain & Cable Drain Trim Kit
1096756_2_A
2 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to Kallista quality products. Please take a moment to review this manual be-
fore you install your Kallista product. If you encounter any installation or performance problems, please do not
hesitate to contact us at the phone number listed at the bottom of the page.
TOOLS
Plumbers
Putty
Adjustable
Wrench
Level
P-Trap
Spanner
(supplied)
Hex Wrench
(supplied)
Caulk
Gun
Tape
Measure
Silicone
Sealant
Keyhole or Saber Saw Hacksaw
BEFORE YOU BEGIN
CAUTION: Risk of product damage. Do not kink or cause damage to the cable during installation.
Observe all local plumbing and building codes.
Turn off the main water supplies.
Refer to the roughing-in dimensions of your bath to properly install this product.
Carefully inspect the ttings for damage before installing.
If you are installing a new bath, install the drain before installing the bath.
Kallista reserves the right to make revisions in the design of products without notice, as specied in the 
Price Book.

INSTALLATION INSTRUCTIONS
Cable Drain & Cable Drain Trim Kit
1096756_2_A
3 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
ROUGH-IN DIAGRAM1.
7/16”
2-9/16”
1-1/8”
20-11/16”
Max
21-1/2”
Max
8-7/8”
Max
3-1/8”
2-3/16”
Max
2-5/16”
1-9/16”
4-1/4”
3-7/16”
Max
2-5/16”
1-1/2”
Max
3-7/16”
Optional Tee
(Included)
3-15/16”
1-15/16”
1-3/16”
1-7/8”
Max
2-7/8”
8-7/8”
Max
20”
Max
1-3/16”
Max

INSTALLATION INSTRUCTIONS
Cable Drain & Cable Drain Trim Kit
1096756_2_A
4 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INITIAL ASSEMBLY2.
Drain
Elbow
Compression Seal
Compression Ring
Coupling Nut
Tee
Coupling Nut
Compression Ring
Compression Seal
Overflow Elbow
Overflow Pipe
Drain Pipe
Tailpiece
Coupling Nut
Compression Ring
Compression Seal
If using tee with compression joints:
Remove the overow body, waste body, tailpiece and tee 
from the packaging.
Disassemble the coupling nuts, compression rings, and
compression seals from the tee.
Assemble the drain elbow, drain pipe, tee, tailpiece, over-
ow pipe and overow elbow. Test t the assembly to the
bathtub.
If necessary, mark and cut the drain pipe and overow 
pipe, using the dimensions in the rough-in diagram and the
rough-in information for the tub as a guide.
Remove any sharp edges and retest t to bathtub.
Disassemble the drain elbow, drain pipe, tee, tailpiece,
overow pipe and overow elbow.
Slide a coupling nut, compression ring, and compression
seal onto the overow pipe. Repeat this process on the
drain pipe and tailpiece.
Fit the overow pipe, tailpiece, and drain pipe into the tee.
Hand tighten the coupling nuts onto the tee allowing move-
ment of the overow body, drain body, and tailpiece.
Do not fully tighten the coupling nuts until instructed to do
so.
If using tee with soldered joints:
Drain
Elbow
Tee
Overflow Elbow
Overflow Pipe
Drain Pipe
Tailpiece
Assemble the drain elbow, drain pipe, tee, tailpiece, overow pipe and 
overow elbow. Test t the assembly to the bathtub.
If necessary, mark and cut the drain pipe and overow pipe, using the 
dimensions in the rough-in diagram and the rough-in information for
the tub as a guide.
Remove any sharp edges and retest t to bathtub.
Do not solder the joints until instructed to do so.

INSTALLATION INSTRUCTIONS
Cable Drain & Cable Drain Trim Kit
1096756_2_A
5 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALL THE WASTE AND OVERFLOW3.
Apply
plumbers
putty.
Drain
Gasket
Nut
Flange
Drain
Outlet
Threaded
Cylinder
Drain Elbow
Backplate
Nut
Overflow Outlet
Overflow Elbow
Threaded
Cylinder
Overflow
Seal
CAUTION: Risk of product damage. Do not kink or cause damage to the cable during installation.
CAUTION: Risk of property damage. Make sure a watertight seal exists on all bath drain connections.
Apply plumbers putty to the underside of the ange.
Set the ange on top of the drain outlet.
Apply silicone sealant to the underside of the drain gasket, then place the drain gasket on top of the drain
elbow.
Insert the nut through the center of the ange and onto the threaded cylinder in the drain elbow.
Hand tighten the nut onto the threaded cylinder. Do not wrench tighten at this time.
Remove any excess putty from around the ange.
Remove the overow seal from the packaging and position it on top of the overow elbow.
Apply plumbers putty or other sealant to the top edge of the overow seal according to the putty manufac-
turer’s instructions.
Align the overow elbow to the outside of the overow outlet.
Insert the nut through the recessed side of the backplate.
Insert the nut with backplate onto the threaded cylinder of the overow elbow.
Turn the nut clockwise until hand-tight to secure the nut with backplate to the threaded cylinder. Do not
wrench tighten at this time.

INSTALLATION INSTRUCTIONS
Cable Drain & Cable Drain Trim Kit
1096756_2_A
6 of 6
Questions? Problems? For additional assistance, please contact Kallista’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
COMPLETE THE INSTALLATION4.
Overflow Outlet
Handle
Setscrew
Plug
Drain
Outlet
Secure the Connections and Fittings
Wrench tighten all connections and ttings to one quarter turn past hand-
tight.
If using soldered connections, solder all joints at the tee.
Install the Trim
Insert the plug into the drain outlet. Adjust the height of the plug, if desired.
NOTE: To ensure the setscrew does not inadvertently fall down the drain
outlet, push down on the plug to close the drain hole.
Secure the handle to the overow outlet with the setscrew.
Turn the handle counterclockwise and clockwise to ensure proper opera-
tion of the plug.
Complete the Bath Installation
Install the bath faucet according to the bath faucet manufacturer’s installa-
tion guide.
Refer to the bath manufacturer’s installation guide to complete the nished 
deck or wall around the bath.