Kallista P24603-CR User manual

INSTALLATION INSTRUCTIONS
Deck-Mounted Bath Set
1144944_2_A
1 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
P24603-CR P24603-LV

INSTALLATION INSTRUCTIONS
Deck-Mounted Bath Set
1144944_2_A
2 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
THANK YOU FOR CHOOSING KALLISTA
We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual
before you install your KALLISTA product. If you encounter any installation or performance problems, please do
not hesitate to contact us at the phone number listed at the bottom of the page.
TOOLS
Tube Cutter Silicone Sealant
Hex
Wrench
Adjustable
Wrench
Phillips
Screwdriver
IMPORTANT INFORMATION
Please read all instructions before you begin.
Shut off the main water supply.
Observe all local building codes.
Complete the nished deck material before installing.
Before installation, unpack the new faucet trim and inspect it for damage. Return it to the carton until
installation.
KALLISTA reserves the right to make revisions in the design of products without notice, as specied in the 
Price Book.
REMOVE THE PIPE PLUG1.
CLOSE
COLD
CLOSE
HOT
3/8” Pipe Plug
WARNING: Risk of personal injury. Lines may be pressurized. Do
not lean over the pipe plug when turning or removing the plug.
Make sure the valves are closed (cold = fully counterclockwise; hot =
fully clockwise).
Turn off the main water supply
Wrap a rag around the pipe plug to prevent water spray.
IMPORTANT! Water may purge from the supply tube when you remove
the plug.
Carefully remove the pipe plug.

INSTALLATION INSTRUCTIONS
Deck-Mounted Bath Set
1144944_2_A
3 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
PREPARE FOR SPOUT INSTALLATION2.
Rough
Deck
Tile
1-1/2” (3.8 cm)
Remove the plaster guard from the spout supply tube.
Cut off the spout supply tube 1-1/2” (3.8 cm) above the rim,
nished deck, or tile.
Remove all burrs from the supply tube to prevent damage to the
O-ring seal.
INSTALL THE SLEEVE3.
Spout Supply Tube
Setscrews
Sleeve
Washer
Spacer
CAUTION: Risk of product damage. Use care when installing the
spout assembly to prevent damage to the O-ring seal.
IMPORTANT! Keep the spout supply tube clean above the nished deck to
avoid damage to the O-ring seal.
NOTE: The washer is not needed for rim/nished deck installation.
If the installation includes a tile covered rough deck, slide the washer,
at side facing forward, onto the supply tube.
If a spacer is provided, slide the spacer onto the supply tube.
Loosen the setscrews in the sleeve.
Use a twisting motion to install the sleeve on the spout supply tube
until it contacts the deck or washer, or spacer.
Align the sleeve with the setscrews offset from the center (not facing
directly forward or backward) of the supply tube.

INSTALLATION INSTRUCTIONS
Deck-Mounted Bath Set
1144944_2_A
4 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALL THE SPOUT4.
Sleeve
Spout
O-ring
Setscrew
Plug
Remove the setscrew from the back of the spout assembly.
Install an O-ring in the bottom of the spout.
Position the spout on the sleeve, and carefully press down until the spout
contacts the nished deck.
Align the spout as desired and tighten the setscrew.
Install the plug into the setscrew.
If desired, apply a bead of silicone sealant around the base of the spout
according to the manufacturer’s instructions.
INSTALL THE HANDLES5.
Handle Assembly
Screw
Sleeve
Stem Extension
O-ring
NOTE: The hardware pack contains two different length stem
extensions and screws. Choose the stem extension and screw
combination that works for your installation.
Make sure the valves are closed (cold = fully counterclockwise;
hot = fully clockwise).
Install a stem extension on one of the valve stems.
Remove the sleeve from a handle assembly.
With the handle oriented correctly, place a handle assembly over
the stem extension and verify correct handle alignment.
NOTE: The handle alignment can be adjusted by removing the
handle assembly and stem extension. Rotate the stem extension
one tooth and replace. Replace the handle assembly and check
the alignment. Repeat this procedure until the handle alignment is
satisfactory.
Remove the handle assembly and secure the stem extension to
the valve with the screw.
Re-install the sleeve into the handle assembly.
With the handle oriented correctly, hold the handle with one
hand and thread the handle assembly into the valve assembly
with the other hand.

INSTALLATION INSTRUCTIONS
Deck-Mounted Bath Set
1144944_2_A
5 of 5
Questions? Problems? For additional assistance, please contact KALLISTA’s Customer
Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX [phone].
INSTALL THE HANDLES (CONT’D)
Repeat the procedure with the other handle assembly.
If desired, apply a bead of silicone sealant around the base of the handle assemblies according to the
manufacturer’s instructions.
COMPLETE INSTALLATION6.
Ensure that both faucet handles are turned off (cold = fully
counterclockwise; hot = fully clockwise).
Turn on the main water supply, and check for leaks. Repair as required.
Turn on both hot and cold valves, and run water through the spout for
about a minute to remove any debris.
Turn off both hot and cold valves.