Kanomax TABmaster 6715 User manual

TABmaster Model 6715
Instruction Manual
Be sure to read this manual thoroughly before using the instrument ,
fully understand and pay attention to each cautions mentioned.
Please well-keeping this manual for long time service reference .
01003
14.10

1
CONTENTS
Product Configuration..................................................................................................................... 3
Caution........................................................................................................................................... 5
1. Introduction................................................................................................................................ 7
1.1. Features............................................................................................................................. 7
1.2. Specifications..................................................................................................................... 7
2. Outlook & Structure.................................................................................................................... 8
2.1. Base structure.................................................................................................................... 8
2.2. Micromanometer............................................................................................................... 9
3. Settubg up................................................................................................................................... 9
3.1. Capture Hood.................................................................................................................... 9
3.2. Velocity Grid.....................................................................................................................10
3.3. Pitot tube..........................................................................................................................11
3.4. Micromanometer..............................................................................................................11
3.5. Shoulder Strap..................................................................................................................11
4. Operating Instruction.................................................................................................................12
4.1. Power supply ....................................................................................................................12
4.2. Start On / Power Off.........................................................................................................12
4.3. Keypad operation..............................................................................................................13
5. Function test...............................................................................................................................14
5.1. User Interface...................................................................................................................14
5.2. Single Mode......................................................................................................................15
5.3. Average Mode ...................................................................................................................15
5.4. Back Pressure Mode..........................................................................................................15
6. Menu setting...............................................................................................................................16
6.1. General setting..................................................................................................................17
6.1.1. Date........................................................................................................................17
6.1.2. Time.......................................................................................................................17
6.1.3. Auto Off..................................................................................................................17
6.1.4. Backlighting............................................................................................................18
6.1.5. Communication.......................................................................................................18
6.2. Test setting........................................................................................................................19

2
6.2.1. Tools.......................................................................................................................19
6.2.2. ID application .........................................................................................................20
6.2.3. Test Mode ...............................................................................................................20
6.2.5. Data record.............................................................................................................21
6.2.6. Standard/Actual test................................................................................................21
6.2.7. Compensation factor ...............................................................................................22
7 Error and Troubleshooting...........................................................................................................23
8 Warranty and Service..................................................................................................................24
8.1. Product Warranty.............................................................................................................24
8.2. After service......................................................................................................................24

3
Product Configuration.
6715 Standard:
Item.
Qt’y
Micromanometer Model 6700
1
Instrument Base
1
Fabric Hood: 2ft×2ft
1
Carrying case
1
Portable handle
1
Frames
1
Poles
4
Communication cable
1
Calibration certificate
1
CD-Rom（Manual and software inside）
1
Quick-Guide
1
6715 Optional Parts:
Item.
Specifications
Spare hood 2x2ft
Spare hood 2x4ft
Spare hood 1x4ft
Spare hood 3x2ft
Spare hood 3x3ft
Spare hood 500x500mm
Poles
Capture Hood Stand
Up to 3.4m with capture hood
Communication cable
Printer
AC adapter
DC5V
International plug adapter
Carrying case
Velocity Grid
Pitot tube (2.3 x 200mm)
Pitot tube (4 x 300mm)
Pitot tube (8 x 500mm)
Pressure tubing
2*250cm

4
6700 Standard:
Item.
Qt’y
Micromanometer Model 6700
1
Carrying case
1
Pressure tubing
2
Communication cable
1
Calibration certificate
1
CD-Rom（Manual and software inside）
1
Quick-Guide
1
6700 Optional Parts:
Item.
Specifications
Velocity Grid
Pitot tube (2.3 x 200mm)
Pitot tube (4 x 300mm)
Pitot tube (8 x 500mm)
Pressure tubing
2*250cm
Shoulder Strap
Printer
AC adapter
DC5V
International plug adapter
Communication cable

5
Caution.
The symbols for warning mentioned in this manual are defined below:
〔symbols classifications〕
Danger: To Prevent Serious Injury or Death
Wa rnings in this classification indicate a danger that ma y resultin serious injury or death if not observed .
Caution: To Prevent Damage to the Product
Wa rnings in this classification indica te a risk of damage to the product tha t ma y void the product warranty if not
observed.
〔Description of Symbols〕
△This s ymbol indi cates a condition that requires caution (including danger). The subject of ea ch caution is
illustra ted inside the triangle .
This s ymbol indicates a prohibition. Do not take the prohibited a ction shown inside or nea r this s ymbol .
●This symbol indicates a mandatory action. A specific action is given near the symbol.
WARNING
Heated forbidden
○Never bring the fabric hood to a flammable gas
atmosphere.
…otherwise, the hea t may cause a fi re or explosion.
Disassemble
prohibition
○Do not disassembl y or refit the instrument.
…otherwise, may cause the electric shock or a fi re.
Using properly
○Using properly under the instruction manual.
…otherwise, ma y cause sensor damaged or an electric shock even a fire.
Using properly
○If abnormal smells, noises or s moke occur, or if liquid enters the instrument, pull out
the AC adapter and remove the batteries immediatel y. Then send it to the
maintenance Dept. of KANOMAX for after servi ce.
…or, there is possible of an electric shock or a fi re or instrument malfunction.
Forbidden
○Do not expose the fabri c hood, base and the instrument
noumenon in the rain.
…otherwise, ma y cause an electric shock, an fire and an
person injure.

6
CAUTION
Using properly
○Always unplug when the instrument not in use.
…Failure to do so ma y cause an electric shock, an fire or circuit damage.
Using properly
○Remove the batteries when storing the instrument for a l ong period. Do not leave
the exhaused batteries in the ba ttery comparement and exchange the ba ttereis on
time.
…Failure to do so may cause the batteries leakage and the instrument damage.
Using properly
○Matching the correct AC adapter outwa rd as reqested.
…or may cause the instrument damage.
Forbidden
○Do not wipe the instrument with a vola tile solvent.
…the body may deform or deteri orate. Use a soft dry cl oth to remove stains. If stains
persist, soak the cloth in a neutral detergent a nd wipe the i nstrument with the soft
cloth. Never use volatile solvents such as thinner or benzene .
Forbidden
○Do not use or leave the instrument in a high
temperature, high humidity or dusty environment. Do
notlea ve the instrument under direct sunlight.
…otherwise, the instrument ma y not function properly
out of the specified opera ting conditions or the inside
components damaged.
Forbidden
○Never dropping the unit or pla cing heavy objects on it
…It may cause damage or malfunction to the instrument

7
1. Introduction
TABmaster Model 6715 is a kind of intelligent test instrument with multi functional of airflow test, velocity
test and micro-Differential pressure test. It’s widely used in air flow and velocity testing of air - conditioning,
HAVC system and other places, especially for the high precision micro differential pressure test.
1.1. Features
3.5 inch true color LCD.
Available measuring the air flow, velocity, temperature and humidity at the same time.
Two kinds of tests are available of in flowing and exhaust flowing.
Back pressure compensation.
Ultra-large Storage capacity: 8000 records
Blue tooth communication makes remote monitoring and data transferring available.
Light weight, compact configuration for easy carrying.
Data printing or transferring to the computer.
1.2. Specifications
Items
Specifications
Air flow
Test range
40～4300 m3/h
Accuracy
±3% of readings ± 8m3/h（＞85m3/h）
Resolution
1 m3/h
Air velocity
Test range
0.15～40 m/s（Pitot Tube）、 0.15～15 m/s（Velocity Grid)
Accuracy
±3% of readings ±0.05m/s（＞0.25m/s）
Resolution
0.01m/s
Differential
pressure
Test range
-2500~2500 Pa
Accuracy
±0.25% of readings ±1Pa
Resolution
0.001 Pa
Temperature
Test range
0～60℃
Accuracy
±0.5℃
Resolution
0.1℃
Humidity
Test range
0~100%RH
Accuracy
±3%RH（10~90%RH）
Resolution
0.1%RH
Absolute
pressure
Test range
70~130 kPa
Accuracy
±2% of readings
Resolution
0.1 kPa
Operation Temp.
0~60℃（non condensing ）
Storage Temp.
-20~70℃（non condensing）
Power Source
4 pcs of AA-size buttery ( approx. 9hrs available）or DC5V Adapter
Weight
3.6kg approx.

8
2. Outlook & Structure
2.1. Base structure
1．Outlook
2．Internal view 3．Grid
Testing
point
Fabric
Hood
Micromanometer
Pivot
Wi ndow
Frame
Poles
Instrument
Base
Poles
Grid
Back pressure plate
Test handle
Base buttom
Micromanometer
Back pressure
ON/OFF
Potable handle
Adjust handle

9
2.2. Micromanometer
3. Settubg up
3.1. Capture Hood
1．Fabric Hood & basement
、
Note：
1）Make sure the elastic band of the fabric hood is placed exactly as shown (Figure(3)) to ensure a good fit.
The elastic band must lineup with the top lip of the base as shown. If you don’t line it up correctly, the
hood might slide off the base when you insert the poles.
2）Use the 4 positioning holes on the base stitching as a guide to ensure the hood fully wraps around the
base..
2．Frame Poles
Front view
Top view
Bottom view
Back
Cover lock
Mini USB Port
Power on/off
Air port (+)
Air port (-)
Keypad
Display LCD
Battery Compartment Cover
（1）
（2）
（3）
（4）

10
Note: The poles always cross in an “X” shape when assembling. To remove the poles, simply reverse the steps.
3．Potable handle
Note: Release the poles and portable handle when packing in the carring case to avoid case damaged.
4．Micromanometer & basement
Note: 1）Correct install the micromanometer to the ba se with the same S/N No.
2）Do not cross- insert the Air pines just refer to the figure as above.
3.2. Velocity Grid
Air velocity testing can be achieved when micromanometer work together with the velocity Grid.
①
②
(+) (-)

11
Note: Mounting angle between the Grid and handle can be adjusted as request.
3.3. Pitot tube
Air flow and velocity testing can be achieved when micromanometer work together with Pitot tube.
3.4. Micromanometer
Differential pressure testing can be achieved by using the micromanometer.
Device
under test
3.5. Shoulder Strap
When testing by Velocity Grid、Pitot tube、Micromanometer as the tool, for convenient view and easy
operation, the shoulder strap can be fit for using.
（+）（ -）
Static pressure
port
Testing point
（+）（ -）
（+）（ -）
Handle
Grid

12
4. Operating Instruction
4.1. Power supply
1．Power by AC adapter. AC adapter will be as the priority power supply when the AC adapter and batteries are
all available using. The specification of the AC adapter is: I/P:AC 110-240V 50/60HZ O/P:DC 5V/2A。
1）AC adapter for the master 2）AC adapter for Capture Hood
2．Power by battery
4 AA-size batteries can be used for a power supply.
Press the compartment cover lock (refer to figure indicating ①/②), and then slide the cover off to open
the battery compartment。
Put 4 AA-size batteries in and make certain the batteries are correctly oriented.
New alkaline battery or rechargeable Ni-MH battery can be used. Never mix battery types, or battery
leakage or damage to the instrument may occur.
Replace the compartment cover (refer to figure ③). The compartment cover will be automatically locked.
When power is supplied with batteries, the current charge value will be displayed on the upper of the LCD.
When the batteries run out of power, the instrument will turn off.
Note：
1）Do not test with low battery power.
2）Do not mixing use full power battery with low power ones for ensure testing well.
3）Change the batteries in time when power shows low for ensure testing well.
4.2. Start On / Power Off
①
②
③
Power off

13
2014/03/20
13:10
20.5
℃
30.7
%RH
m
3
/h
Atmos:kPa
Ready
ID:
Cycle:
Mode:
01
001
Single
START
SAVE
MENU
99.0
1. Start On
Press button【POWER】for 2 seconds for start On, displaying “KANOMAX”then enter into the testing
interface.
2. Power Off
Press【POWER】for 2 seconds, shut down and power off.
4.3. Keypad operation
Keypad panel includes control buttons, back-pressure switch and LCD adjusting keys.
1．Control buttons:
UP：Value increasing or Cursors upward moving.
SAVE：Save the current test results
SET：Store changes or enter into the selected option’s next level interface
MENU：On the main screen holding this down for 2 seconds will enter into the main “MENU”
OK：In the “General Setting”, pressing for 2 seconds will save the date or time ;
While in the “Record Processing”, pressing for 2 seconds will delete saved data.
START：Begin a measurement in main menu
STOP：Stop a measurement in main menu
BACK：Cancel or end an operation or return to the previous screen
EXIT：Return to the main menu
ESC：Stop printing when printing
DOWN:：Value decreasing or Cursors downward moving
2．Back pressure switch for on/off
Note ：
1) If you are not in the back pressure mode, shut down the back pressure plate and lock the
switch to avoid testing errors.
2) If the airflow is greater than 1500m3/h (883CFM), testing in back-pressure Mode is
recommended according to testing procedures.
POWER
START/STOP
SAVE
UP/SAVE
DOWN
SET/MENU/OK
START/STOP/
BACK/EXIT/ESC

14
3．LCD adjusting
Note ：
1）Please switching the handle slow gently during LCD adjusting.
2）Stop turning when reach to the bound, for avoiding over turning and handle falling down.
5. Function test
Besides the airflow test, if along with other optional products, test air velocity and micro -differential
pressure is available.
5.1. User Interface
Testing information, parameter settings and the testing conditions will be displayed on the main interface.
A. Date and time —— real-time display the current date and time
B. Testing data display —— airflow 、air velocity 、differential pressure and etc.
C. Tools icon —— working tools display
D. Testing condition —— temperature 、humidity or absolute pressure displaying according to the
Back pressure
On
Back pressure
Off
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Ready
ID:
Cycle:
Mode:
01
001
Single
START SAVE MENU
99.0
B
C
D
E
A
I
H
G
F
J

15
working tools.
E. Keypad —— current status indicating and the grey state is not available.
F. Testing mode —— display the current testing mode
G. Cycle—— recorded Cycle quantity
H. ID—— current ID quantity
I. Power supply —— AC adapter or batteries
J. Blue tooth status —— when blue tooth working, the icon display or no icon display with closed.
5.2. Single Mode
Note：
1）START: Left-button for the Micromanometer or instrument base
2）After testing start for about 8s with stably measuring,output displaying the test data and testing wind
direction.
3）Testing stop when finish outputting.
4）Press SAVE for data record with adding 1 to the Cycle value.
5）Same testing method with the capture hood when using the Velocity Grid、Pitot、Micromanometer.
5.3. Average Mode
Note：
1）START: Left-button for the Micromanometer or instrument base.
2）After testing start for about 8s with stably measuring , output displaying the test data for the first time.
3）Go on the testing with frequency of 1s for data updating.
4）The continuously outputting is as the average data and be related with the “AvgTime”set by user. More
larger of the value of“AvgTime”will get more stable of the testing data.
5）If auto-save function On, testing data will be recorded automatically according to the setting “AutoSave”
and value of “Cycle”will be added automatically.
6）Press “STOP”, testing stop. And “STOP”will be as the Left-button for the Micromanometer or instrument
base.
7）Same testing method with the capture hood when using the Velocity Grid、Pitot、Micromanometer.
5.4. Back Pressure Mode
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Waiting...
ID:
Cycle:
Mode:
01
001
Avg
99.0
STOP SAVE MENU
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
32 ID:
Cycle:
Mode:
01
001
Avg
99.0
STOP SAVE MENU
1.Ready for tes ting
2. Testing
3. test output
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
31 ID:
Cycle:
Mode:
01
001
Avg
99.0
STOP SAVE MENU
4. testing stop
STOP
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Ready
ID:
Cycle:
Mode:
01
001
Avg
START SAVE MENU
99.0
START
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Ready
ID:
Cycle:
Mode:
01
001
Single
START SAVE MENU
99.0
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Waiting...
ID:
Cycle:
Mode:
01
001
Single
99.0
STOP SAVE MENU
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
32 ID:
Cycle:
Mode:
01
001
Single
99.0
START SAVE MENU
START
1. Ready for testing
待测状态
2. Testing
3. tes t output

16
In order to reduce the measure error of the pressure loss,which causing from the hood to the system and
get the more real air flow, we suggest testing under the Back Pressure Mode when air flow more than 1500
m3/h.
Note：
1）START: Left-button for the Micromanometer or instrument base.
2）After testing start for about 8s , indicating “Open Flap”. It’s time for switching on the Back-Pressure Plate
as needed.
3）When Back-Pressure Plate opened On, tip of “Open Flap” disappear.
4）Press START for about 8s, testing stop, real airflow outputting with back pressure compensation.
5）Press SAVE for testing data record and the meanwhile, value Cycle added 1.
6）When select Velocity Grid、Pitot tube、Micromanometer for testing, Back-Pressure compensation will be
not available.
6. Menu setting
when stop for ready, press for 2s for enter into the menu.
MENU
General Setting
Test Setting
UP
DOWN
OK
EXIT
SET
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Ready
ID:
Cycle:
Mode:
01
001
Avg
START SAVE MENU
99.0
（1）2 opti onal settings ：
1）Basi c setting
2）Test setting
3）Working tool displayi ng below
2s
4. swi tch on Back-Pressure Pla te
5. testing ready
6. testing
2. Testing
1.Ready for tes ting
7. test output
8. shut off the pla te
9. testing ready
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Ready
ID:
Cycle：
Mode:
01
001
B.P
START SAVE MENU
99.0
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
2000 ID:
Cycle:
Mode:
01
001
B.P
99.0
START SAVE MENU
3. Ba ck-pressure On promoting
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Ready
ID:
Cycle:
Mode:
01
001
B.P
START SAVE MENU
99.0
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Open Flap !
ID:
Cycle：
Mode:
01
001
B.P
START SAVE MENU
99.0
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Waiting...
ID:
Cycle:
Mode:
01
001
B.P
99.0
STOP SAVE MENU
START
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Ready
ID:
Cycle：
Mode:
01
001
B.P
START SAVE MENU
99.0
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
Waiting...
ID:
Cycle:
Mode:
01
001
B.P
99.0
STOP SAVE MENU
START

17
6.1. General setting
6.1.1. Date
6.1.2. Time
6.1.3. Auto Off
When instrument not in use, it will be turn off automatically according to Auto-Off time setting to avoid
power waste.
MENU
General Setting
Test Setting
UP
DOWN
OK
EXIT
SET
（1）Basic setting：
1）Date
2）Time
3）Auto Shut
4）Backlight
5）Communicate
2s
(1) press or for data modify.
(2)press , for sele cting Year/Month/day.
(3)Press for 2s for save settings.
(4)Press for quit.
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
High
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
20 / 03 / 20
13 : 10
Off
High
14
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 04 / 01
13 : 10
Off
High
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 04 / 01
13 : 10
Off
High
01
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
High
2s
2s
(1)Press or for data modify.
(2)Press for hour/minute selection.
(3)Press for 2s for save settings.
(4)Press for quit.
(1)按或键进行数值更改。
(2)按键，时/分选项循环移动。
(3)长按 键2s，保存设置。
(4)按键，退出设置。
General Setting
1.
2.
3.
4.
5.
Data
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
: 10
Off
High
13
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
High
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
15 : 15
Off
High
General Setting
1.
2.
3.
4.
5.
Data
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
15 : 15
Off
High
15

18
6.1.4. Backlighting
Adjust the LCD lighting according to the environmental brightness for the best viewing. And meanwhile, the
lower the brightness, the less battery power will be needed.
6.1.5. Communication
Communicate with PC, printer and Bluetooth are available. Data transfer or remote monitoring is available
by selecting communicating way.
Note：
1）PC communication means to save the testing record to the computer. And the communication cable and
software reserved for data-fetching are necessary for using together. Refer to the << Manuel for Data
fetching Software>> .
2）For printing out the testing record, the optional printer and cables for special are necessary. Printer baud
rate is set to 19200 bps and Do not change it. Refer to the << Manuel for RD series Mini printer >> .
3）Bluetooth make the remote control and data monitoring available by Hand phone. And our APP software is
necessary for using together. Refer to the << Manuel for TAB Mobile>>.
4）Shut off the switch when not use the Bluetooth communication for improving battery life.
(1)Press or for o ptions cha nge.
(2)Press for save settings .
(3)Press for quit.
(1)Press or fo r opti ons cha nge.
(2)Press for save settings .
(3)Press for quit.
(3)按键，退出设置。
General Setting
1.
2.
3.
4.
5.
Data
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
20 min
10 min
30 min
60 min
General Setting
1.
2.
3.
4.
5.
Data
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
20 min
10 min
30 min
60 min
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
High
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
10 min
High
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
High
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
Low
High
Normal
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
High
Low
Normal
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
Low

19
5）If other settings need to be changed when Bluetooth successful communication, you need to shutdown
Bluetooth firstly then enter the menu to change other settings. Just as below shown:
6.2. Test setting
6.2.1. Tools
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
32 ID:
Cycle:
Mode:
01
001
Avg
START SAVE OFF
99.0
2014 / 03 / 20 13 : 10
20.5 ℃30.7 %RH
m3/h
Atmos: kPa
32 ID:
Cycle:
Mode:
01
001
Avg
START SAVE MENU
99.0
2s
Communicate
1.
2.
3.
Computer
Printer
Bluetooth
UP
DOWN
OK
BACK
SET
Off
Print
1.
2. Print By IDs Print By Cycles
UP
DOWN
OK
BACK
SET
Communicate
1.
2.
3.
Computer
Printer
Bluetooth
UP
DOWN
OK
BACK
SET
Off
Communicate
1.
2.
3.
Computer
Printer
Bluetooth
UP
DOWN
OK
BACK
SET
Off
Computer
Comfirm the Connection
UP
DOWN
OK
BACK
SET
Waiting...
Communicate
1.
2.
3.
Computer
Printer
Bluetooth
UP
DOWN
OK
BACK
SET
On
General Setting
1.
2.
3.
4.
5.
Date
Time
Auto Shut
Backlight
Communicate
UP
DOWN
OK
BACK
SET
2014 / 03 / 20
13 : 10
Off
High
Test settings：
1）Select Tool
2）Test ID
3）Test Mode
4）Unit
5）Data Record
6）Standard/Actual testing
7）Compensation factor
MENU
General Setting
Test Setting
UP
DOWN
OK
EXIT
SET
Test Setting
1.
2.
3.
4.
5.
Select Tool
Test ID
Test Mode
Unit
Data Record
UP
DOWN
OK
BACK
SET
RunAvg
6.
7. Std/Act
K factor 1.000
Act