Kanto L100 TV User manual

User Manual
L100 TV Mount
Supporting your digital lifestyle™
TILTING FLAT PANEL TV MOUNT
English
19” - 32” 56 lbs
(25 kg)
50 x 50
to
200 x 200 VESA
COMPLIANT
±12°
30°

Introduction
Table of Contents
Table of Contents / Introduction . . . . . . . . . . . . . 2
Supplied Parts & Hardware ..................3
Setup - Step 1............................4
Setup - Step 2............................5
Setup - Steps 3 to 5 .......................6
Other Kanto Products ......................7
Warranty ................................8
2
Thank you for choosing a Kanto tilting wall mount. The L100 is designed to mount flat panel televisions weighing up to 56
lbs (25 kg) within 3” of your wall, allow you to swivel left and right approximately 30° (depending on TV size), and tilt your
TV ±12°.
Read these instructions fully before installation of this mount. If you do not understand these directions, or have any
doubts about the safety of the installation, please consult a qualified installation contractor to install this mount.
Make sure there are no defective or missing parts. Do not use defective parts. If there is hardware missing, or if you
are uncertain whether the part is defective call Kanto directly at 1-888-848-2643 or [email protected]. Kanto
cannot be liable for property damage or injury caused by incorrect mounting, incorrect assembly, lifting or incorrect
use of this product.
This product should not be mounted on steel stud walls or cinder block walls. Consult a qualified installation con-
tractor if you are unsure about the type of wall you may have.
CAUTION
The wall you plan to affix the Kanto mount to must be able to support more than 5 times the weight of the
television and the wall mount combined. Do not use this product for any purpose other than to mount a flat panel
TV on a vertical surface as outlined in this manual. Improper installation may cause damage to your TV or serious
injury. This product should not be mounted to steel stud walls, cinder block or old concrete walls. Consult a qualified
installation contractor if you are unsure about the type of wall you may have.
CAUTION
The maximum loading weight is 56 lbs (25 kg). This wall mount is intended for use only within the maximum
weight restrictions indicated. Use with products heavier than the maximum weights indicated may result in instability
causing possible injury. Recommended TV Size: 19 inch to 32 inch.
See installation video online at:
www.kantoliving.com/product/mount/l100#video

Supporting your digital lifestyle™
Supplied Parts and Hardware
3
A: Wall Plate B: Arm Assembly C: TV Plate
E: M4 x 12mm
Bolt
D: Screw Cover
F: M4 x 30mm
Bolt
G: M6 x 12mm
Bolt
H: M6 x 35mm
Bolt
L: Lag Bolt
M: Concrete Anchor
x4 x4 x4 x4
J: M6 Washer
x6
K: Plastic Spacer
x4 x4
I: M4 Washer
x8
x4
N: Safety Knob
x2
O: Allen Bolt
x2
P: Spring Washer
x2
Q: Allen Key
Required Tools
Phillips
Screwdriver
Hammer (for
concrete
installs)
Pencil Stud
Finder
Level Drill
5/16”
Masonry
Bit
5/32”
Wood
Bit

Step 1.1 Select the correct size of bolt.
Kanto provides 2 bolt diameters (Metric sizes M4 and M6)
in various lengths. Part items: E, F, G, H.
Select the correct diameter bolt and hand screw into the
back of the TV to determine the correct length. Use the
longest available bolt without reaching the bottom of
the TV threads, using spacers (K) if your TV has a curved
back or a deep recess.
Step 1.2 Attach TV plate to the back of the TV.
Insert the selected Bolts through the appropriate
washers (Ior J), TV Plate, and Spacers (K) (if necessary),
then thread into the mounting holes (see Diagram A).
4
WARNING
Never over-tighten a screw into the back of your flat panel TV.
Do not lay the TV face down on its glass front. Use a wall or a TV stand.
Step 1: Attach TV Plate
Diagram A
Washer (I or J)
Screws (E thru H)
There are a wide variety of TVs available that require different bolt sizes. We provide a selection of mounting bolts to
fit most TVs. If you have any concerns about this mounting hardware or installation call us direct at 1-888-848-2643 or
email at [e-mail].
Spacer (K), if necessary
for curved TVs

Supporting your digital lifestyle™Supporting your digital lifestyle™
5
Step 2: Mount Wall Plate
Wood Stud Wall
The Wall Plate must be mounted to a wood stud. Use a
stud sensor to locate the stud, clearly marking the outer
edges of the stud. Align the Wall Plate (with the Stop
Screw at the bottom of the plate - see Diagram B) so that
all four screws will screw into the stud, and mark the top
hole.
Pre-drill the top hole, then temporarily attach the Wall
Plate to the wall using a Lag Bolt (L). Using a level, ensure
that the Wall Plate is level, and mark the three remaining
holes. Remove the Wall Plate and drill the remaining
holes. Attach the Wall Plate using 4 Lag Bolts (L) (see
Diagram B). Do not over-tighten lag bolts (L). Make sure
the Wall Plate is flat against the wall surface.
Brick or Concrete Wall
Using the Wall Plate as a template (with the Stop Screw
at the bottom of the plate - see Diagram C), use a level
to ensure that the Wall Plate is level, then mark the
four holes at your desired height. Adjust the Wall Plate
position to be clear of mortar joints.
Pre-drill four holes, and insert a Concrete Anchor (M)
into each of the holes flush with the concrete wall surface
and not flush with the surface covering, such as drywall.
Attach the Wall Plate using 4 Lag Bolts (L) (see Diagram
C). Make sure the Wall Plate is flat against the wall
surface. Do not over-tighten Lag Bolts (L).
CAUTION
Make sure the supporting surface will support
the load limits outlined in the Caution at bottom
of page two. Tighten Lag Bolts until the Wall Plate is
snug flat against the wall. Do not over tighten Lag Bolts
(L). Each Lag Bolt must be screwed into a wood stud.
CAUTION
Make sure the concrete or brick wall is at least
2” thick. Make sure the anchor is seated completely flush
with the concrete surface even if there is another layer
of material, such as drywall. If drywall is over 5/8” thick
custom lag bolts must be used. Concrete must be
a minimum of 2000psi in density.
Diagram B Diagram C
Wood Concrete
5/32”
(4 mm)
2” (50 mm) 2” (50 mm)
5/16”
(8mm)
M
LL
Stop Screw
at bottom Stop Screw
at bottom

Step 3: Insert Arm Assembly
into Wall Plate
Step 4: Attach TV to Wall Plate
Assemble the Arm Assembly and Screw Cover, then slide
the two parts together into the channel on the Wall Plate, as
shown in Diagram D.
The Arm Assembly will stop when it hits the Stop Screw.
Lift the TV on to the Wall Plate, hooking the TV Plate on to
the pegs of the Arm Assembly, as shown in Diagram E.
CAUTION
Read this section carefully prior to install.
WARNING
Use two people to lift and position the TV onto the Wall Plate.
Diagram D
6
Diagram E
Hook
Peg
A
D
B
Step 5: Attach the Tilt Knobs
With your TV mounted to the wall plate, insert the Safety
Knobs (N) through Washer (J) and Spring Washer (P), then
through the mounting slot on the TV Bracket and into
the threaded holes on the Arm Assembly, as shown in
Diagram F. You can then tilt the TV ±12° to your desired
viewing angle, tighten the Safety Knobs, and pan the TV
approximately 30° in either direction. Your installation is
complete.
If preferred, you can use the supplied Allen Bolts (O) in
place of the Safety Knobs (N), if you do not plan to use
the tilt function regularly.
Diagram F
N
J
P

Supporting your digital lifestyle™
7
To learn more about all our products, visit www.kantoliving.com
• Check out our full line of bookshelf and desktop speaker systems
• Available in a stunning array of colors
Kanto Speakers
• Full line of Audio and Video Cables
• Attractive white cables and heads
• HDMI, Optical, Mini-jack, RCA, USB
• Switchers, Hubs, Adapters
• Visit kantoliving.com/cable for more!
• Visit kantospeakers.com for more!
BEN
by
kantoliving kantoliving
Check out more great products from Kanto!

Limited Warranty To Original Purchaser
Kanto Distribution Inc. (Kanto) warrants the equipment it manufactures to be free from defects in material and workmanship
for the following limited warranty period of:
24 months parts and labour
If equipment fails because of such defects and Kanto or an authorized dealer is notified within 24 months from the date
of shipment with proof of original invoice, Kanto will, at its option, repair or replace the equipment, provided that the
equipment has not been subjected to mechanical, electrical, or other abuse or modifications. Equipment that fails under
conditions other than those covered will be repaired at the current price of parts and labor in effect at the repair. Such repairs
are warranted for 90 days from the day of reshipment to the original purchaser. This warranty is in lieu of all other warranties
expressed or implied, including without limitation, any implied warranty or merchantability or fitness for any particular
purpose, all of which are expressly disclaimed.
The information in the owner’s manual has been carefully checked and is believed to be accurate. However, Kanto assumes
no responsibility for any inaccuracies that may be contained in the manual. In no event will Kanto, be liable for direct, indirect,
special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the
possibility of such damages.
Warranty
13-09
www.kantoliving.com
[email protected]
Tel [phone]