KaVo KaVo Primus 1058 Life TM Installation guide

Care instructions
Primus 1058 Life

Manufacturer:
Kaltenbach & Voigt GmbH
Bismarckring 39
D-88400 Biberach
www.kavo.com
Distributed by:
KaVo Dental GmbH
Bismarckring 39
D-88400 Biberach
Phone [phone]
Fax [phone]

Table of contents
1User instructions............................................................................................................................................... 4
1.1 User guide................................................................................................................................................ 4
1.1.1 Abbreviations............................................................................................................................... 4
1.1.2 Symbols....................................................................................................................................... 4
1.1.3 Target group................................................................................................................................ 4
2Setup methods according to DIN EN ISO 17664............................................................................................. 5
2.1 References............................................................................................................................................... 5
2.2 General instructions for the reprocessing of KaVo treatment units.......................................................... 5
2.2.1 Reprocessing Overview Primus 1058 Life................................................................................... 8
2.3 Reprocessing of the surfaces of treatment unit / upholstery..................................................................... 8
2.4 Preparation of the dentist unit................................................................................................................... 9
2.4.1 Reprocessing of handle and holder pad/anti-slip mat................................................................. 9
2.4.2 Reprocessing of the instrument holder of the TM table............................................................. 11
2.4.3 Reprocessing of the instrument arm S table............................................................................. 12
2.4.4 Setting up the 3-function and multifunction handpiece.............................................................. 14
2.4.5 Preparation of the instrument hoses......................................................................................... 16
2.4.6 Servicing the turbine return air filter........................................................................................... 17
2.4.7 Reprocessing KaVo ERGOcam One......................................................................................... 17
2.5 Reprocessing of the assistant unit.......................................................................................................... 19
2.5.1 Preparing the instrument holder................................................................................................ 19
2.5.2 Preparing the connector for the suction hose............................................................................ 19
2.5.3 Reprocessing of sieve inserts and suction hoses..................................................................... 20
2.6 Preparation of the patient unit................................................................................................................. 20
2.6.1 Preparation of the tumbler......................................................................................................... 20
2.6.2 Preparation of the tumbler holder and filler............................................................................... 20
2.6.3 Preparation of the spittoon........................................................................................................ 22
2.7 Manual reprocessing of the water-conducting system............................................................................ 23
2.8 Automatic hygiene functions of the water conducting system................................................................ 23
2.8.1 Rinsing programme................................................................................................................... 24
2.8.2 Intensive germ reduction........................................................................................................... 27
2.9 Reprocessing and automatic hygiene functions of the suction system.................................................. 30
2.9.1 Reprocessing of the suction system including suction hoses................................................... 30
2.9.2 HYDROclean function............................................................................................................... 31
2.10 Preparation of the amalgam separator................................................................................................... 31
2.11 Reprocessing KaVo Screen One / KaVo Screen HD............................................................................. 32
3Replenish and check the disinfectant............................................................................................................. 33
3.1 Replenish OXYGENAL 6........................................................................................................................ 33
3.1.1 Replenish OXYGENAL 6 when using the water bottle.............................................................. 34
3.2 Check the OXYGENAL 6 concentration................................................................................................. 37
Care instructions Primus 1058 Life
Table of contents
3 / 40

Care instructions Primus 1058 Life
1 User instructions | 1.1 User guide
4 / 40
1 User instructions
1.1 User guide
Requirement
Read these instructions prior to first use to avoid misuse and prevent damage.
Note
Comply with the Instructions for Use of the treatment unit!
1.1.1 Abbreviations
Abbre‐
viation
Explanation
IfU Instructions for use
CI Care instructions
AI Assembly instructions
TI Technician's instructions
SC Safety checks
IEC International Electrotechnical Commission
RI Repair instructions
EMC Electromagnetic compatibility
Scaler Scaler (ZEG)
IR Infrared
IrDA Infrared Data Association
1.1.2 Symbols
Refer to the chapter on Safety/Warning symbol
Important information for users and service technicians
Action request
CE mark according to Medical Devices Directive EC 93/42
Thermodisinfectable at up to 95 °C (203 °F)
Suitable for steam sterilisation at up to 135 oC (275 °F)
1.1.3 Target group
This document is for dentists and dental office staff.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.1 References
2 Setup methods according to DIN EN ISO 17664
2.1 References
The reprocessing consists of the following basic steps:
▪ Cleaning and disinfection ( manually or automatically)
▪ Sterilisation
Note
Comply with national hygiene requirements, e.g. RKI guidelines.
CAUTION
Risk of injury during cleaning of the treatment unit.
Lack of instructions to the cleaning staff and lack of preparation of the treatment unit
can lead to the cleaning personnel sustaining injuries.
▶ Only trained professionals and instructed cleaning personnel may be present in
the treatment rooms.
▶ Position the chair for cleaning and turn the device off.
CAUTION
Product damage due to improper disinfection.
Malfunctions.
▶ Use the disinfectant as prescribed by the manufacturer.
▶ No spray disinfection, perform wipe disinfection only.
▶ Do not immerse product or parts of the product in liquids.
▶ Mop up any spilled cleanser or disinfectant immediately.
CAUTION
Improper disinfection may lead to health hazards and material damage.
Infection hazard to users and patients.
Damage to the sterile product.
▶ No hot air sterilisation, no chemical cold sterilisation, do not sterilise with ethylene
oxide.
CAUTION
Health hazard and property damage due to non-compliance with servicing schedule.
Infection hazard to users and patients.
Product damage.
▶ Comply with servicing schedule.
Note
The preparation methods for the instruments and motors are found in the separate
instructions for use that accompany the instrument and motor packages.
2.2 General instructions for the reprocessing of KaVo treatment units
Please comply with the general reprocessing instructions at all times. Detailed prod‐
uct-specific reprocessing instructions are provided subsequently.
At the site of use ▶ Remove any surface contamination using a
disposable cloth/paper towel.
5 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.2 General instructions for the reprocessing of KaVo treatment units
6 / 40
Storage and transport KaVo recommends reprocessing as soon as possible after use.
Preparations for cleaning ▶ Comply with product-specific reprocessing
instructions.
Manual cleaning Fixtures:
▪ Brush or cloth
▪ Tap water 30 °C ± 5 °C
▶ Remove any dirt on the surface using a suit‐
able cleanser according to the recommen‐
dations of the manufacturer. Before doing
so, check the compatibility of the cleanser
on a inconspicuous place of the treatment
centre.
Automatic cleaning KaVo recommends washer disinfectors in accordance with EN ISO
15883-1, which are operated with alkaline cleaning agents with a pH value
of max. 10 (e.g. Miele G 7781 / G 7881 – Validation was carried out with
the "VARIO-TD" programme, cleaning agent "neodisher® mediclean" and
rinsing agent "neodisher® mielclear" and only applies to the material com‐
patibility with KaVo products).
▶ For programme settings as well as cleans‐
ers and disinfectants to be used, please re‐
fer to the Instructions for Use of the washer
disinfector.
▶ Directly after automated cleaning/disinfec‐
tion, treat the medical device with the care
products and systems provided by KaVo.
Manual disinfection ▶ Perform wipe disinfection only, the use of
spray disinfection and disinfection baths is
not feasible.
▶ Wipe all outer surfaces with a soft cloth and
an approved disinfectant.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
▪ Microcide AF Liquid (Schülke & Mayr)
▪ FD 322 (Dürr Dental)
▪ Incidin Liquid (Ecolab)
▶ Use disinfectants according to the manufac‐
turer's Instructions for Use.
▶ Please note the disinfectant safety data
sheet.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.2 General instructions for the reprocessing of KaVo treatment units
Automatic disinfection KaVo recommends washer disinfectors in accordance with EN ISO
15883-1, which are operated with alkaline cleaning agents with a pH value
of max. 10 (e.g. Miele G 7781 / G 7881 – Validation was carried out with
the "VARIO-TD" programme, cleaning agent "neodisher® mediclean" and
rinsing agent "neodisher® mielclear" and only applies to the material com‐
patibility with KaVo products).
▶ For programme settings as well as cleans‐
ers and disinfectants to be used, please re‐
fer to the Instructions for Use of the washer
disinfector.
▶ In order to prevent negative effects on the
medical device, make sure that the interior
and the exterior of the medical device are
dry after completion of the cycle, and then
grease it immediately with servicing agents
from the KaVo care system.
Manual drying ▶ Supply dry, clean and uncontaminated com‐
pressed air according to ISO 7494-2 only.
▶ Blow off the outside and inside with com‐
pressed air until water drops are no longer
visible.
Automatic drying Usually, automatic drying is part of the cleaning/disinfection cycle of the
washer disinfector and should not be carried out above 95 °C.
Servicing ▶ Discard damaged products.
Control and functional test ▶ Perform a visual inspection to check for
damage and wear and tear.
▶ Test products for function regularly.
Packaging ▶ Use standardised packaging material. Seal‐
ing should not be under tension.
▶ Use sterile goods packaging in order to en‐
sure sterility.
Sterilisation All sterilisable products are temperature-resistant up to max. 138 °C.
Select a suitable procedure (depending on the available autoclave) from
the following sterilisation processes:
▪ Autoclave with three times pre-vacuum:
- at least 3 minutes at 134 °C -1 °C / +4 °C (273 °F -1.6 °F / +7.4 °F)
▪ Autoclave using the gravity method:
- at least 10 minutes at 134 °C -1 °C / +4 °C (273 °F -1.6 °F / +7.4 °F)
▶ Use according to the manufacturer's Instruc‐
tions for Use.
Storage ▶ Reprocessed products should be stored pro‐
tected from dust with minimum exposure to
germs in a dry, dark and cool place.
▶ Comply with the expiry date of the sterilised
items.
7 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.3 Reprocessing of the surfaces of treatment unit / upholstery
8 / 40
2.2.1 Reprocessing Overview Primus 1058 Life
Reprocessing items/medical devi‐
ces
Cleaning Disinfection Sterilisation
manual automatic manual automatic automatic
Surfaces
Unit
Cushion
Gripping sleeve, white
Gripping sleeve, grey
Light
Dentist element
Handpiece sleeve 3F and MF hand‐
pieces
Cannula for 3F and MF handpieces
Holder pad/anti-slip mat
Handpiece holder
Swing-arm S-table
Assistant element
Connection parts of the suction
hose
Patient element
Tumbler support
Tumbler filler
Porcelain spittoon bowl
Glass spittoon bowl
2.3 Reprocessing of the surfaces of treatment unit / upholstery
Position the chair for cleaning
▶ Adjust the backrest to vertical position and move the chair upward.
Also refer to:
Instructions for use
Turn device off
▶ Switch main device switch off.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
Cleaning and disinfecting the surfaces of treatment unit / upholstery
CAUTION
Non-colour-fast textiles.
Non-colour-fast textiles can cause permanent discoloration.
▶ Remove discolourations with water immediately.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
▪ Microcide AF Liquid (Schülke & Mayr)
▪ FD 322 (Dürr Dental)
▪ Incidin Liquid (Ecolab)
▶ Clean the surfaces and upholstery with a soft cloth and water, and wipe-disinfect
them with an approved surface disinfectant.
CAUTION
Damage caused by spray disinfection.
Disinfectant gets into cracks and loosens the paint.
▶ No spray disinfection.
▶ Only disinfect by wiping.
Cleaning and disinfection of the foot control
CAUTION
Damage caused by inappropriate use of water.
Damage to the foot control.
▶ For cleaning, the foot control must not be immersed in water or placed under run‐
ning water.
▶ When wiping it off with a moist cloth, do not touch the contacts of the charge
socket.
▶ Only wipe off. Do not spray.
2.4 Preparation of the dentist unit
2.4.1 Reprocessing of handle and holder pad/anti-slip mat
Note
The handle of the TM table cannot be detached.
9 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
10 / 40
Cleaning and disinfection of the handle TM table / cart
▶ Clean the handle with a soft cloth and water, and wipe-disinfect it with an ap‐
proved surface disinfectant.
Cleaning and disinfection of S-table handle and holder pad/anti-slip mat
▶ Press the push button and pull off the handle.
▶ Clean the handle under flowing water.
▶ Disinfect the white and grey handle by wiping or thermodisinfection (minor disco‐
louration may occur).
▶ Sterilise the holder pad and anti-slip mat by thermodisinfection.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
Sterilisation of S-table handle and holder pad/anti-slip mat
CAUTION
Damage caused by sterilisation.
▶ Do not sterilise the white standard handle.
▶ Sterilise the holder pad/ anti-slip mat.
The grey handle (Mat. no. 1.002.4489) can be sterilised (see symbol on the handle).
2.4.2 Reprocessing of the instrument holder of the TM table
Note
The handpiece holder (Mat. no. 3.001.4229) can be removed to facilitate cleaning.
Cleaning and disinfection of the instrument holder
CAUTION
Damage caused by thermodisinfection.
▶ Do not thermodisinfect the instrument holder.
▶ Place the instrument hoses in the provided places of the germ reduction attach‐
ment during the cleaning and germ reduction of the handpiece holder.
11 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
12 / 40
▶ Pull the latches evenly outward and carefully remove the handpiece holder.
▶ Clean the handpiece holder under running water.
▶ Wipe-disinfect the instrument holder.
Sterilize the instrument holder
CAUTION
Damage caused by sterilisation.
▶ Do not sterilise the instrument holder.
2.4.3 Reprocessing of the instrument arm S table
Note
The instrument arm S table (Mat. no. 1.007.4756) can be removed to facilitate
cleaning.
Cleaning and disinfection of the instrument arm S table
CAUTION
Damage caused by thermodisinfection.
▶ Do not sterilise the instrument arm S table by thermodisinfection.
Note
Neither the rinsing program nor the intensive germ reduction can be carried out
when the instrument arm is removed.
▶ Switch off the unit at the main switch.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
▶ Fit the germ reduction attachment to the spittoon bowl.
▶ Take the handpieces off the hoses.
▶ Take the roller out of the instrument arm and then place the hose in the germ re‐
duction attachment.
▶ Pull-off the swing-arm in an upward direction.
▶ Clean the swing-arm and roller under running water.
▶ Wipe the instrument arm S table with disinfectant.
Sterilisation of instrument arm S table
CAUTION
Damage caused by sterilisation.
▶ Do not sterilise the instrument arm S table
13 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
14 / 40
2.4.4 Setting up the 3-function and multifunction handpiece
Note
Wet the O-rings of the gripping sleeves after sterilisation using silicone grease (Mat.
no. 1.000.6403) or KaVo Rota Spray 2 (Mat. no. 0.411.7510). After replacing the
cannula, the air channel must be blown out before the start of treatment to ensure
that the air exiting during treatment is dry.
Cleaning the triple-function and multifunctional handpiece
Automatic cleaning
Not applicable.
CAUTION
Damage caused by improper cleaning/disinfection.
▶ Do not wash the gripping sleeve and the cannula in the thermodisinfector.
▶ Do not sterilise the gripping sleeve and the cannula in the hot-air steriliser.
▶ Do not place the gripping sleeve and the cannula in a disinfectant or ultrasonic
bath.
Manual cleaning
Note
Combine manual cleaning with disinfection.
Cleaning the interior
▶ Leave the gripping sleeve and cannula on the instrument, and activate the air and
water for 60 seconds.
External cleaning
CAUTION
Danger of injury if the valve body is hot (heating elements, high-pressure lamp).
Risk of burn injury.
▶ Switch off the unit at the main switch.
▶ Let the handpiece cool after long use.
Accessories required:
▪ Tap water 30oC ± 5oC
▪ Brush, e.g. medium-hard toothbrush
▶ Disassemble the gripping sleeve and cannula.
▶ Detach the key part from the gripping sleeve.
▶ Clean the key part, gripping sleeve and cannula by brushing them under running
water (at least tap water quality).
▶ Immediately remove contamination from materials used in the dental practice (im‐
pression materials, caustic chemicals).

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
▶ Carefully wipe off contamination from the cannula tip with a soft Q-tip or soft cloth
and water.
CAUTION
Damage caused by using a nozzle needle that is too long.
Damage to the internal hoses of the cannula.
▶ Use a short nozzle needle (Mat. no. 1.004.4986) to clean the media exit holes.
▶ Carefully remove contamination from the media exit ports using the short nozzle
cleaning needle.
Disinfection of the 3-function and multifunction handpiece
Manual disinfection
External disinfection
▶ Wipe-disinfect the surfaces with a soft cloth.
Automatic disinfection
Not applicable.
CAUTION
Damage caused by improper cleaning/disinfection.
▶ Do not wash the gripping sleeve and the cannula in the thermodisinfector.
▶ Do not sterilise the gripping sleeve and the cannula in the hot-air steriliser.
▶ Do not place the gripping sleeve and the cannula in a disinfectant or ultrasonic
bath.
Drying the 3-function and multifunction handpiece
Manual drying
▶ Blow off the outside and inside with compressed air until water drops are no lon‐
ger visible.
Automatic drying
Not applicable.
Care of the 3-function and multifunctional handpiece
Requirement
The multifunctional handpiece has been reprocessed.
15 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
16 / 40
▶ Apply KaVo silicone grease (Mat. no. 1.000.6403) or KaVo Rota Spray 2 (Mat. no.
0.411.7510) to the O-rings of the joint between the gripping sleeve and cannula.
Use cotton buds for this purpose.
Sterilising the 3-function and multifunction handpiece
Note
The grip sleeve and cannula can be sterilised.
▶ Hold the 3-way or multifunctional handpiece at the gripping sleeve and take off the
cannula with a slight twisting motion.
▶ Pull the gripping sleeve off the valve body.
Sterilization in a steam sterilizer in compliance with DIN EN 13060
▶ Weld the cannula and grip sleeve in sterile goods packaging.
▶ Sterilise with a triple fractionated vacuum (B class steriliser); hold for 4 minutes;
134°C ± 1 °C; overpressure: 2.13 bar.
CAUTION
Damage caused by over-heating.
Damage to the gripping sleeve.
▶ Immediately remove the parts from the steriliser after the sterilisation cycle is
completed.
Storage
▶ Reprocessed products should be stored protected from dust with minimum expo‐
sure to germs in a dry, dark and cool place.
2.4.5 Preparation of the instrument hoses
Cleaning and disinfection of instrument hoses
▶ Clean the hoses and couplings with a cloth and water.
CAUTION
Damage caused by spray disinfection.
▶ Do not subject instrument hoses to spray disinfection.
▶ Subject instrument hoses to wipe disinfection.

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
2.4.6 Servicing the turbine return air filter
Cleaning the turbine return air filter
Note
The liquid collector must be checked weekly.
▶ If there is any liquid in the filter, drain the liquid and replace the O-rings of the mul‐
tiflex couplings.
▶ If necessary, replace the turbine return air filter (Mat. no. 0.200.3098) and clean
the filter holder.
Note
The turbine return air filter is in the same position in the dentist element variant with
S table.
2.4.7 Reprocessing KaVo ERGOcam One
Note
The camera handle cannot be sterilised or disinfected with heat.
Cleaning
Note
Disinfect the camera before cleaning.
Disinfect after cleaning if necessary.
Exterior cleaning by hand
CAUTION
Damage to camera due to improper cleaning.
To avoid the surface or optical system of the camera being destroyed:
▶ Do not use abrasives or aggressive cleaning substances
▶ Do not immerse camera in water or other fluids
▶ Switch main device switch off.
▶ Remove the camera.
17 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.4 Preparation of the dentist unit
18 / 40
▶ Clean the surface with a soft cloth and mild liquid cleaning agent.
Disinfection
Exterior disinfection by hand
WARNING
Highly flammable gases-.
Explosion.
▶ Allow product to cool before disinfecting.
CAUTION
Damage to the camera due to improper disinfection.
Irreversible destruction of the camera.
▶ Disinfect with wipes only, do not use disinfectant sprays.
▶ Do not immerse the camera in liquids.
▶ Do not sterilise the camera in an autoclave!
▶ Do not store the camera in steri pack.
▶ Do not sterilise the camera with hot air or thermo disinfectant.
▶ Switch main device switch off.
▶ Allow the camera to cool down.
▶ Remove the camera.
▶ Disinfect the surface using a soft wipe and disinfectant.
Approved disinfectants:
▪ CaviCide / CaviWipes (Metrex)
▪ Microcide AF Liquid (Schülke & Mayr)

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.5 Reprocessing of the assistant unit
▪ FD 322 (Dürr Dental)
▪ Incidin Liquid (Ecolab)
Note
The exterior of the camera and camera hose can be disinfected with chemical disin‐
fectants.
Comply with the manufacturer's instructions for use with regard to the application
range. and exposure time.
CAUTION
Material damage due to use of non-approved disinfectant.
Damage to the camera.
▶ Use approved disinfectants only.
2.5 Reprocessing of the assistant unit
2.5.1 Preparing the instrument holder
The instrument holder on the assistant unit is prepared in the same way as the instru‐
ment holder on the dentist unit.
See also:
22.4.2 Reprocessing of the instrument holder of the TM table, Page 11
2.5.2 Preparing the connector for the suction hose
▶ Remove connectors ① and ② from the suction hoses.
Cleaning and disinfection of the suction hose connector
▶ Clean the disassembled parts under running water.
▶ Thermodisinfect the disassembled parts for at least 10 minutes at 93 °C (total cy‐
cle: approximately 20 minutes)
Sterilising the suction hose connector
CAUTION
Damage caused by sterilisation.
▶ Do not sterilise the suction hose connector.
Note
Sterilise the suction cannulas according to the manufacturer's instructions.
19 / 40

Care instructions Primus 1058 Life
2 Setup methods according to DIN EN ISO 17664 | 2.6 Preparation of the patient unit
20 / 40
2.5.3 Reprocessing of sieve inserts and suction hoses
Note
Check the sieve inserts daily and after each surgery. The sieve inserts must be re‐
placed at the latest when the suction decreases (Mat. no. 0.763.3423).
Cleaning is not recommended for hygienic reasons.
▶ Remove the suction hoses from the holder.
ðThe suction motor starts automatically when the suction tubes are removed from
the holder.
▶ Hold the cloth under the sieve seat, and pull the sieve insert out of the housing.
▶ If needed, insert a new sieve insert (Mat. no. 07633423) into the seat.
▶ Wipe the suction tubes with disinfectant.
2.6 Preparation of the patient unit
2.6.1 Preparation of the tumbler
▶ Reprocess as specified by the manufacturer.
2.6.2 Preparation of the tumbler holder and filler
CAUTION
Water in the device.
Material damage from leaking water upon actuation of the "Tumbler filler" or "Bowl
flush" keys.
▶ Make sure that the unit is turned off before removing the tumbler filler or the spit‐
toon bowl.
▶ Always check the correct seating of tumbler filler and spittoon bowl before turning
on the unit.
Cleaning and disinfection of the tumbler holder and filler
Note
When assembling, make sure that the O-ring is present on the tumbler filler.