Kaycee Ovijector Instructions for use

INSTRUCTION AND
MAINTENANCE MANUAL
OVIJECTOR
HAND HELD SELF-FILLING REPEATER SYRINGE
ADJUSTABLE DOSAGE
MK1 0.1ml • 0.2ml • 0.3ml • 0.4ml • 0.5ml
0.6ml • 0.7ml • 0.8ml • 0.9ml • 1.0ml
MK2 0.5ml • 0.75ml • 1.0ml • 1.25ml • 1.5ml • 1.75ml • 2.0ml
MK3 1.0ml • 1.5ml • 2.0ml • 2.5ml • 3.0ml
3.5ml • 4.0ml • 4.5ml • 5.0ml

KAYCEE VETERINARY PRODUCTS LIMITED
14 Enterprise Park
Lewes Road
Lindfield
West Sussex
RH16 2LH
United Kingdom
T [phone]
F [phone]
E [e-mail]
Your Kaycee syringe is a hand-
operated repeater syringe which
has been designed for use with
all oil and water-based vaccines.
It is comfortable to handle and
its ergonomic design allows long
sessions without operator-fatigue.
This accurate, robust and easy to
maintain device is factory set using
digital calibration and will last many
years if well maintained.

aRemove handgrip with an anticlockwise turn and
set aside.
s DO NOT BOIL HANDGRIP
bPlace syringe in distilled or previously boiled water
and pump trigger several times to fill syringe.
Add all other items for sterilising eg Hypodermic
needles, vaccine feed tube, feed needle or Multifit
Direct Bottlemount or Cap assembly and bottle
(unscrew bottle from cap).
cBoil for 10 minutes.
dAllow to cool, refit handle and pump out water.
1. Sterilisation
2. Setting the dose
The numbers on the dose knob show the dose
amount in ml. In order to set the Ovijector to the
dose required, twist the dose knob at the base of
the handgrip. It will click into precise dose settings
each complete turn. Read the dose setting at the
extreme end of the handgrip.

The self-filling Kaycee syringes can be fitted with:
a. rear connector and tube feed into vaccine container
b. Multifit bottle holder
c. Cap assembly and bottle.
aFit the PVC feed tube to rear connector and
short vaccine feed needle to the other end of the
tube. Attach feed needle to vaccine container.
If container is rigid, use of an air needle will be
required to relieve vacuum;
s FAILURE TO RELIEVE VACUUM MAY RESULT
IN UNDER-DOSING
b(Please note the Multifit can be located on top or
rear of vaccinator as required.)
-To attach bottle to Multifit holder first remove red
needle cover from air vent needle.
-Carefully remove the seal from the cap of the
bottle, ensuring the remaining cap is left in place.
-Pierce centre of rubber seal firmly so bottle head
enters ‘crown’ of Multifit holder.
-Slide and click ring completely over crown
segments to lock bottle.
-If ring doesn’t click over round crown segments,
loosen crown anti-clockwise and try again.
-Once it has clicked, turn crown clockwise for final
adjust.
cWhen using cap assembly and bottle, fill bottle with
vaccine and screw inverted syringe firmly down
onto bottle.
dOnce vaccine is connected using desired
attachment, fit hypodermic needle to front stem
(ensuring needle is facing away from operator) and
pump the trigger several times to prime the device
until fluid flows from the needle. Your syringe is
now ready for use.
3. Connect vaccine

Immediately after use, pump through with hot soapy
water, followed by clean water. This is essential to
ensure blockages do not occur due to a build-up
of residue and to promote the long life of your
instrument.
Remove piston and lubricate ‘O’-ring with medicinal
liquid paraffin or Caster oil and refit piston, do not
interchange pistons between syringes as they are
individually calibrated for accuracy.
4. Maintenance
aIf you experience difficulty when
priming the syringe and vaccine
is not initially drawn through, use
a disposable syringe with a short
piece of PVC tubing attached
to the front stem to draw the
vaccine through.
bThe syringe is designed and
built to give a high degree of
accuracy. If accuracy should
fail, check for residual matter
stuck on the valves.
-Unscrew and remove delivery
option. i.e. Rear connector,
multifit bottle holder or cap
assembly bottlemount.
-Ensure suction valve and
valve spring are clean and
undamaged and no residual
matter appears in rear connector
or rear of vaccinator.
-Replace parts as in diagram
ensuring correct orientation of
suction valve.
cIf after long service there is
leakage from the base of the
handgrip, remove piston and fit
new ‘o’ ring and lubricate with
Liquid paraffin or Caster oil
before replacing piston.
5. Troubleshooting

Parts list - Rear Connector Fitting
OVIJECTOR (REAR CONNECTOR FITTING) Cat. No
01 Luer lock stem 40mm 10091
Luer lock stem 60mm 10092
02 Fibre washer 10157
03 Valve spring 10169
04 Delivery valve (conical) 10170
05 Suction valve (semi-sphere) 10182
06 Trigger screw 10194
07 Trigger 10200
08 Handle grip MK1, MK2 10224
Handle grip MK3 10236
11 Hexagon screw (plain) 10273
12 Main body MK1 10327
Main body MK2 10339
Main body MK3 10340
13 Side arm 10418
14 ‘O’-Ring MK1 10455
‘O’-Ring MK2 10467
‘O’-Ring MK3 10479
15 Piston MK1 10522
Piston MK2 10534
Piston MK3 10546
16 Main spring MK1, MK2 10571
Main spring MK3 10583
17 Chest plug 10280
OV Spares kit MK1 10789
OV Spares kit MK2 10790
OV Spares kit MK3 10807
s PLEASE STATE VACCINATOR MODEL WHEN ORDERING

Parts list - Cap Assembly Bottle
s PLEASE STATE VACCINATOR MODEL WHEN ORDERING
OVIJECTOR (CAP ASSEMBLY BOTTLE) Cat. No
01 Luer lock stem 40mm 10091
Luer lock stem 60mm 10092
02 Fibre washer 10157
03 Valve spring 10169
04 Delivery valve (conical) 10170
05 Suction valve (semi-sphere) 10182
06 Trigger screw 10194
07 Trigger 10200
08 Handle grip MK1, MK2 10224
Handle grip MK3 10236
11 Hexagon screw (plain) 10273
12 Main body MK1 10327
Main body MK2 10339
Main body MK3 10340
13 Side arm 10418
14 ‘O’-Ring MK1 10455
‘O’-Ring MK2 10467
‘O’-Ring MK3 10479
15 Piston MK1 10522
Piston MK2 10534
Piston MK3 10546
16 Main spring MK1, MK2 10571
Main spring MK3 10583
17 Chest plug 10280
19 Cap assembly 10297
20 Bottle 125ml 10364
21 Multifit attachment with 22mm crown 10821
22 Needle chest 10822
23 Valve cap seat 10830
24 Crown 22mm 10825
25 Locking ring 22mm 10826
26 Ball valve 10824
OV Spares kit MK1 10789
OV Spares kit MK2 10790
OV Spares kit MK3 10807

Parts list - Multifit Bottle Holder
OVIJECTOR (MULTIFIT BOTTLE HOLDER) Cat. No
01 Luer lock stem 40mm 10091
Luer lock stem 60mm 10092
02 Fibre washer 10157
03 Valve spring 10169
04 Delivery valve (conical) 10170
05 Suction valve (semi-sphere) 10182
06 Trigger screw 10194
07 Trigger 10200
08 Handle grip MK1, MK2 10224
Handle grip MK3 10236
11 Hexagon screw (plain) 10273
12 Main body MK1 10327
Main body MK2 10339
Main body MK3 10340
13 Side arm 10418
14 ‘O’-Ring MK1 10455
‘O’-Ring MK2 10467
‘O’-Ring MK3 10479
15 Piston MK1 10522
Piston MK2 10534
Piston MK3 10546
16 Main spring MK1, MK2 10571
Main spring MK3 10583
17 Chest plug 10280
19 Cap assembly 10297
20 Bottle 125ml 10364
21 Multifit attachment with 22mm crown 10821
22 Needle chest 10822
23 Valve cap seat 10830
24 Crown 22mm 10825
25 Locking ring 22mm 10826
26 Ball valve 10824
OV Spares kit MK1 with multifit bottle fitting 10808
OV Spares kit MK2 with multifit bottle fitting 10809
OV Spares kit MK3 with multifit bottle fitting 10810
s PLEASE STATE VACCINATOR MODEL WHEN ORDERING

www.kaycee.co.uk
Visit our website to see our full range of syringes and accessories
Distributor: