KBC ESUGS8-B User manual

ESUGS8-B
Quick Start Guide
Rev 1903

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 2 of 12
Index
1INTRODUCTION ..................................................................................................3
1.1 ESUGS8-B Introduction .............................................................................. 3
1.2 Features ............................................................................................... 3
1.3 Specifications......................................................................................... 4
2PANEL VIEWS .....................................................................................................5
2.1 Front Panel View ..................................................................................... 5
2.2 Status Indicator LED ................................................................................. 6
3DIMENSIONS (UNIT: mm) .......................................................................................7
4MOUNTING........................................................................................................8
4.1 DIN Mounting ......................................................................................... 8
4.2 Wall Mounting ........................................................................................ 8
4.3 Items for Attention .................................................................................. 9
4.4 Grounding ............................................................................................. 9
5 CABLE ........................................................................................................... 10
5.1 Ethernet Cable ......................................................................................10

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 3 of 12
1INTRODUCTION
1.1 ESUGS8-B Introduction
ESUGS8-B is an unmanaged PoE/PoE+ industrial Ethernet switch with
8*10/100/1000M auto sensing electrical ports. This product supports PoE/PoE+.
Each electrical port outputs up to 30W. Rugged design with IP40 enclosure and
industrial level 3 protection makes it suitable for applications such as Intelligent
Transportation System, IP surveillance and industrial networks.
1.2 Features
−Unmanaged industrial switch
−8*10/100/1000Base-T ports
−Support IEEE802.3af/at
−Dual 45~57VDC power input
−Level 3 ESD protection
−IP-40 housing design
−Operation temperature: -40~+75℃
−Support DIN-rail or wall mounted
−Unique DIN mount design makes mount and removal easy
−Installation: Plug-and-play, no setting required

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 4 of 12
1.3 Specifications
Ethernet
10/100/1000Base-T
8
PoE Standard
IEEE802.3af/at
Switch Performance
Architecture
Store and forward
Switch Capacity
16Gbps
Power
Redundant Input Power
Dual DC inputs. 45~57VDC, 5-pin screw terminal
Power Consumption (Max.)
< 6W (without PoE)
PSE Type
End span
PoE Port
Each port up to 30W output
Overload Current Protection
Present
Reverse Polarity Protection
Present
Mechanical
Enclosure
IP40
Dimensions (L x W x H)
62 x 87 x 100 mm
Weight
0.6kg
Environment
Storage Temperature
-40 to +85oC (-40 to 185oF)
Operating Temperature
-40 to +75oC (-40 to 167oF)
Operating Humidity
5% to 95% non-condensing

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 5 of 12
2PANEL VIEWS
2.1 Front Panel View
1
3
5
6
4
+ /L
-/N
+ /L
-/N
4 5 ~ 5 7
VD C
P1
P2
Po E
5
6
7
8
1
2
3
4
2
1
4
3
6
5
8
7
2
1．Power status indication
2．45~57VDC power input
3．PoE status indication
4．Ground screw
5．10/100/1000Base-T port: #1 ~ #4
6．10/100/1000Base-T port: #5 ~ #8
WARNING：This product MUST be mounted to a well-grounded mounting
surface such as a metal panel.

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 6 of 12
2.2 Status Indicator LED
LED
Color
Status
Description
P1
Orange
On
Power 1 is being supplied
Off
Power 1 is not being supplied
P2
Orange
On
Power 2 is being supplied
Off
Power 2 is not being supplied
PoE1-8
Green
On
The corresponding port’s PoE power on
Off
The corresponding port’s PoE power off
10/100/1000Base-T(X)
SPD
Green
On
Speed indicator for 1000Mbps
Off
Speed indicator for 100Mbps and 10Mbps
LINK/ACT
Orange
On
The corresponding port’s link is active
Blinking
Data is being transmitted
Off
The corresponding port’s link is inactive

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 7 of 12
3DIMENSIONS (UNIT: mm)

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 8 of 12
4MOUNTING
4.1 DIN Mounting
Very simple: Press the clamp, insert into rail then loosen hand.
4.2 Wall Mounting
Step 1 Step 2

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 9 of 12
Step 1: Loosen the 4 screws on the rear panel;
Step 2: Mount the accessories on the rear panel;
Step 3: Fix the switch on the wall.
4.3 Items for Attention
−Operating Ambient: If the product is installed in a closed rack, the inside
operating ambient temperature of the rack may be higher than outside. Therefore,
consideration should be given to installing the equipment in an environment
compatible with the maximum operating temperature specified by the
manufacturer.
−Air Flow: Installation of the equipment in a rack should be such that the amount
of air flow required for safe operation of the equipment is not compromised.
−Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring.
−Reliable Earthing: Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g. use of power strips).
4.4 Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic
interference (EMI). Run the ground connection from ground screw to the grounding
surface prior to connecting devices.

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 10 of 12
5CABLE
5.1 Ethernet Cable
The product uses standard Ethernet cable. Depending on the connection type, you
can choose CAT3, 4, 5e, 6 UTP cable to connect to other network devices
(computers, servers, switches, routers, hubs, etc.). The cable properties are listed
in the following table.
Cable
Type
Max Length
Connector
10BASE-T
Cat.3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-T
Cat.5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat.5/Cat.5e/6 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
10BASE-T / 100BASE-T Pin Allocation
For 10BASE-T / 100BASE-T cable, pin 1 and 2 send data, pin 3 and 6 receive data.
10/100Base-T RJ-45 Pin Definition
Pin Number
Signal
PoE
1
TD+
PoE+
2
TD-
PoE+
3
RD+
PoE-
4
null
5
null
6
RD-
PoE-
7
null
8
null

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 11 of 12
1000Base-T RJ-45 Pin Definition
Pin Number
Signal
PoE
1
BI_DA+
PoE+
2
BI_DA-
PoE+
3
BI_DB+
PoE-
4
BI_DC+
5
BI_DC-
6
BI_DB-
PoE-
7
BI_DD+
8
BI_DD-
This switch supports MDI / MDIX auto-flip function. The following table lists the
10/100Base-T MDI/MDI-X / 1000Base-T MDI/MDI-X port pin output.
10/100Base-T MDI/MDI-X Pin Definition
Pin Definition
MDI Port
MDI-X Port
PoE
1
TD+(transmit)
RD+(receive)
PoE+
2
TD-(transmit)
RD-(receive)
PoE+
3
RD+(receive)
TD+(transmit)
PoE-
4
Not used
Not used
5
Not used
Not used
6
RD-(receive)
TD-(transmit)
PoE-
7
Not used
Not used
8
Not used
Not used

ESUGS8-B Quick Start Guide
QSG-QSG-ESUGS8-B_Rev1903 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2019
Page 12 of 12
1000Base-T MDI/MDI-X Pin Definition
Pin Number
MDI Port
MDI-X Port
PoE
1
BI_DA+
BI_DB+
PoE+
2
BI_DA-
BI_DB-
PoE+
3
BI_DB+
BI_DA+
PoE-
4
BI_DC+
BI_DD+
5
BI_DC-
BI_DD-
6
BI_DB
BI_DA-
PoE-
7
BI_DD+
BI_DC+
8
BI_DD-
BI_DC-
Need Help?
Please visit www.kbcnetworks.com or contact your nearest KBC office or dealer.
KBC Networks Contact Information
North America & Canada, USA
Phone: [phone]
Toll-free: [phone]
Email: [e-mail]
LATAM & Caribbean, Mexico
Phone: [phone]
Email: [e-mail]
EMEA, UK
Phone: [phone]
Email: [e-mail]
APAC, China
Phone (1): [phone]
Phone (2): [phone]
Email: [e-mail]