KBC FTL1-S1A-BS User manual

FTL1-S1A-BS
FTL1-S1B-BS
User Manual

Manual-FTL1-S1A-BS FTL1-S1B-BS 10 100M（3U+3U）-Rev1104 Page 2 of 8 www.k cnetworks.com
Copyright © KBC Networks Ltd.
Table of Contents
1. Overview ...........................................................................3
1.1 Introduction : ...3
1.2 Technical Specification....3
1.3 Warranty ..........4
1.4 Instruction of Disassembly.........
2. Installation ........................................................................
2.1 Package Contents ......6
2.2 Transmitter Enclosure ..........................................................6
2.3 Receiver Enclosure ..............................................................7
2.4 Caution ..............................................................................8
2. Install Application ..............................................................8

Manual-FTL1-S1A-BS FTL1-S1B-BS 10 100M（3U+3U）-Rev1104 Page 3 of 8 www.k cnetworks.com
Copyright © KBC Networks Ltd.
1. Overview
1.1 Introduction
The FTL1-S1A-BS/FTL1-S1B-BS Series 10/100M Auto-Sensing Ethernet single-mode
Fiber Optic Transceiver is designed using advanced fiber optic technology. This series
transmit and receive 10/100 Mbps (no adjustment is required) data over a single-mode
optical fiber, extending the Ethernet transmission distance from its normal few hundred
meters to 2 kilometers. By using optical fiber as transmission media, this series continue
to perform its secured, high-speed and long-distance communication even under the
adverse condition such as lighting, power surge and electromagnetic interference;
substantial saving on lighting and power surge protection equipments if copper wires were
used.
The FTL1-S1A-BS/FTL1-S1B-BS Series is fully assembled using SMT components for
stability and reliability.
1.2 Technical Specification
ETHERNET
Supporting standards IEEE802.3 10Base-T, 100Base-T
Data Rate 10/100Mbps auto-sensing, Full Duplex or Half
Duplex
Physical Interface RJ4 , Auto MDI/MDIX
OPTICAL
Number of Fibers 1
Wavelength 1 0nm (Transmitter); 1310nm (Receiver)
Fiber Type 9/12 µm(SM)
Distance 0 ~ 2 Km
Connector Type ST/PC

Manual-FTL1-S1A-BS FTL1-S1B-BS 10 100M（3U+3U）-Rev1104 Page 4 of 8 www.k cnetworks.com
Copyright © KBC Networks Ltd.
GENERAL
Operating Temperature -40 ~ 70˚C / -40 ~ +1 8ºF
Relative Humidity 0 ~ 9 % non-condensing
Mean Time Between Failure (MTBF) > 100,000hrs
Input Voltage + VDC
Enclosure Color Silver
Housing Standard 3U 19” chassis card
1.3 Warranty
 Repair
 Please contact your local distributors when product is defective. Please apply RA in
advance and prepay shipping cost when returning the defective product to us. We
will pay the cost for sending it back to you.
 Please attach a statement clearly describing the problem.
 We will repair defective product under warranty free of charge to our customer.
 years warranty for product only.
 Any unauthorized modification of hardware and software voids the warranty.
 Warranty does not cover mishandling and/or abuse of the product.
Products comply with the following Safety Label for International Fiber Communication
Equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 1 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful Interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at this own expense.
Warning
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Manual-FTL1-S1A-BS FTL1-S1B-BS 10 100M（3U+3U）-Rev1104 Page 5 of 8 www.k cnetworks.com
Copyright © KBC Networks Ltd.
1.4 Instruction of Disassembly
Instruction of Disassembly of KBC Product
(For EU Directive 2002/95/EEC━
━━
━WEEE)
Tools Required:
1) mm flat tip screwdriver
2) Φ3 cross tip screwdriver
3) Φ cross tip screwdriver
4) Size small snip nose pliers
) 1 mm spanner
Steps for Disassembly:
1) Remove tightening screws of box cover (1 or 4-8 screws in general);
2) Remove lock nut for BNC with spanner;
3) Remove cover plate;
4) Remove tightening screws for printed circuit board (PCB);
) In case the assembly has more than one PCB then continue removing the remain
tightening screws until none left;
6) Use snip nose pliers to loose the nut of flange and then remove optic cable
connector (jump wire);
7) Snip off power conducting cable and remove power switch /jack/etc.;
8) Take out all PCBs;
9) Disassembly of product completed.
Notice：
：：
：When a product reaches the end of it’s life—
——
—return to KBC

Manual-FTL1-S1A-BS FTL1-S1B-BS 10 100M（3U+3U）-Rev1104 Page 6 of 8 www.k cnetworks.com
Copyright © KBC Networks Ltd.
2 Installation
2.1 Package Contents
• One FTL1-S1A-BS Transceiver ( Transmitter)
• One FTL1-S1B-BS Transceiver( Receiver )
• Two User Manuals
Please contact dealer or distributor if part is missing or damaged.
2.2 Transmitter Enclosure
Transmitter Back View
Connectors:
TX : Fiber Optic ST
LAN: LAN RJ4
Transmitter Front View

Manual-FTL1-S1A-BS FTL1-S1B-BS 10 100M（3U+3U）-Rev1104 Page 7 of 8 www.k cnetworks.com
Copyright © KBC Networks Ltd.
LEDs Definition:
POWER: On if Power Supply is plugged in.
FIB: Link activity; on if link is OK; flashing if there is activity.
LAN: LAN activity; on if link is OK; flashing if there is activity.
2.3 Receiver Enclosure
Receiver Back View
Connectors:
TX : Fiber Optic ST
LAN: LAN RJ4
Receiver Front View
LEDs Definition:
POWER: On if Power Supply is plugged in.
FIB: Link activity; on if link is OK; flashing if there is activity.
LAN: LAN activity; on if link is OK; flashing if there is activity.

Manual-FTL1-S1A-BS FTL1-S1B-BS 10 100M
（
Copyright © KBC Networks Ltd.
2.4 Caution
• Switch off all power
supply before installation.
•
Ensure fiber is properly aligned to the receiving connector. Avoid forcing in the fiber.
• The Ethernet interface
is an
2.5 Install Application
FT
L1
/FT
L1
Switch or HUB
C
able
SM Fiber
C
able
FTL1-S1A-BS/
FTL1-S1B-BS
FTL1-S1A-BS
/FTL1-S1B-BS
（
3U+3U）-Rev1104 Page 8 of 8
supply before installation.
Ensure fiber is properly aligned to the receiving connector. Avoid forcing in the fiber.
is an
auto-sensing interface.
L1
-S1A-BS
L1
-S1B-BS
Switch or HUB
Switch or HUB
Cable
SM Fiber
C
able
FT
/
FT
www.k cnetworks.com
Ensure fiber is properly aligned to the receiving connector. Avoid forcing in the fiber.
Cable
FT
L1-S1A-BS
FT
L1-S1B-BS