KBC FTL1-S2-MSC User manual

FTL1-S2-MSC
UserManual

Manual-FTL1-Rev1009.pdfPage 2of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
Tableof Contents
1. Overview...........................................................................3
1.1Introduction:...3
1.2TechnicalSpecification ... .3
1.3Warranty. ... ... ...4
1.4 InstructionofDisassembly ... ... ...5
2. Installation........................................................................6
2.1Package Contents .. ....6
2.2TransceiverEnclosure ..........................................................6
2.3Caution.............................................................................. 7
2.4Install Application .............................................................. 8
3. Dimensions.......................................................................9

Manual-FTL1-Rev1009.pdfPage 3of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
1.Overview
1.1Introduction
The FTL1-S2-MSCSeries10/100MAuto-Sensing EthernetMulti-mode FiberOptic
Transceiverisdesigned usingadvanced fiberoptictechnology.Thisseriestransmitand
receive10/100 Mbps(no adjustmentisrequired)dataovertwosingle-mode opticalfibers,
extending theEthernettransmission distancefromitsnormalfewhundred metersto25
kilometers.Byusing opticalfiberastransmission media,thisseriescontinue toperformits
secured,high-speed and long-distancecommunicationeven undertheadversecondition
suchaslighting,powersurge and electromagneticinterference;substantialsavingon
lightingand powersurge protection equipmentsif copperwireswereused.
The FTL1-S2-MSCSeriesisfullyassembled usingSMTcomponentsforstabilityand
reliability.
1.2Technical Specification
ETHERNET
Supporting standards IEEE802.310Base-T,100Base-T
DataRate 10/100Mbpsauto-sensing, FullDuplexorHalf
Duplex
PhysicalInterface RJ45, DCEinterface
OPTICAL
Numberof Fibers 2
Wavelength 1310nm
FiberType 9/125μm(SM)
Distance 0~25km
ConnectorType ST/PC

Manual-FTL1-Rev1009.pdfPage 4of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
GENERAL
Operating Temperature -40 ~70˚C/ -40~+158ºF
RelativeHumidity 0~95%non-condensing
Mean TimeBetween Failure(MTBF)>100,000hrs
PowerSupplyAdaptor Input: 100~240VAC, 50/60Hz,0.5A
Output: +12VDC, 2A
EnclosureColor Silver
Dimensions(L WH) 76mm 70mm 28mm/2.98”2.76”1.10”
1.3Warranty
nRepair
¨Pleasecontactyourlocaldistributorswhen productisdefective.PleaseapplyRAin
advanceand prepayshippingcostwhen returning the defectiveproducttous.We
willpaythecost forsendingit back toyou.
¨Pleaseattachastatement clearlydescribing the problem.
nWewillrepairdefectiveproduct underwarrantyfree ofchargetoourcustomer.
n5yearswarrantyforproduct only.
nAnyunauthorized modification of hardwareandsoftwarevoidsthe warranty.
nWarrantydoesnotcovermishandlingand/orabuseof theproduct.
Productscomplywiththe following SafetyLabelforInternationalFiberCommunication
Equipment.
NOTE:Thisequipment hasbeentested and found tocomplywiththelimitsforaClass A
digitaldevice,pursuanttoPart15ofthe FCC Rules.Theselimitsaredesigned to
provide reasonableprotection againstharmfulinterferencewhen the equipmentis
operatedinacommercialenvironment. Thisequipment generates, usesand can radiate
radiofrequency energyand,ifnotinstalled and used inaccordancewiththe instruction
manual,maycauseharmfulInterferencetoradiocommunications.Operation ofthis
equipmentinaresidentialarea islikelytocauseharmfulinterferenceinwhichcasethe
userwillbe requiredtocorrectthe interferenceat thisownexpense.
Warning
Thisisaclass Aproduct. Inadomesticenvironmentthisproductmaycauseradio
interferenceinwhichcasetheusermaybe required totakeadequatemeasures.

Manual-FTL1-Rev1009.pdfPage 5of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
1.4InstructionofDisassembly
InstructionofDisassemblyofKBC Product
(ForEUDirective2002/95/EEC WEEE)
ToolsRequired:
1)5mm flat tipscrewdriver
2) Φ3cross tipscrewdriver
3) Φ5cross tipscrewdriver
4)Sizesmall snipnosepliers
5)15 mm spanner
StepsforDisassembly:
1)Removetightening screwsof boxcover(1or4-8screwsingeneral);
2)Removelock nut forBNC withspanner;
3)Removecoverplate;
4)Removetightening screwsforprinted circuit board(PCB);
5)Incasetheassemblyhasmorethan one PCBthen continueremoving the remain
tightening screwsuntilnone left;
6)Usesnipnoseplierstoloosethenutofflangeandthen removeopticcable
connector(jumpwire);
7)Snipoffpowerconductingcableand removepowerswitch/jack/etc.;
8)Takeout allPCBs;
9)Disassemblyof productcompleted.
Notice Whenaproductreaches theendofit slife—returntoKBC

Manual-FTL1-Rev1009.pdfPage 6of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
2Installation
2.1PackageContents
•One FTL1-S2-MSCTransceiver
•One powersupplyadaptor
•One UserManual
Pleasecontact dealerordistributorif partismissing ordamaged.
2.2TransceiverEnclosure TransceiverTop View
TransceiverLeftView
Connectors:
GND: Grounded pin
DC orACPowerSupplybetween 12Vand24Vcan be used on thisproduct .
•DC:
＋:+12VDC~+24VDC
－:PowerSupplyGround

Manual-FTL1-Rev1009.pdfPage 7of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
•AC:
Thereisno differencebetween ＋/－,the powersupplycanbe connected intothe
devicedirectly.
TransceiverRightView
Connectors:
TX:FiberOpticST(Transmit )
RX:FiberOpticST(Receive)
LAN:LANRJ45
Beside theEthernet RJ45, therearetwoLEDs:
Thegreen LED:Ethernet Link.Flashingifthe linkisinOK
TheyellowLED:FiberLink.Flashingifthe linkisinOK
2.3Caution
•Switchoff allpowersupplybeforeinstallation.
•Ensurefiberisproperlyaligned tothe receivingconnector.Avoidforcinginthe fiber.
•The FTL1-S2-MSCSeriesisanauto-sensingdevice.

Manual-FTL1-Rev1009.pdfPage 8of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
2.4Install Application
FTL1-S2-MSC
SwitchorHUB
SwitchorHUB
Cable
Cable
SM Fiber
SM Fiber
Cable
Cable
FTL1-S2-MSC
FTL1-S2-MSC
FTL1-S2-MSC

Manual-FTL1-Rev1009.pdfPage 9of 9www.kbcnetworks.com
Copyright KBCNetworksLtd.
3Dimensions(mm)
76
70
67
28