KC STORE FIXTURES 16522 User manual

FRAMELESS GLASS WALL UNIT
#16522
PAGE 1 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899

FRAMELESS GLASS WALL UNIT
#16522
PAGE 2 OF 10
Glass shelves - Qty. 4
Glass top - Qty. 1
Glass sides
Qty. 2
Glass back
Qty. 1
Glass doors
Qty. 2
17" 24"46-1/2"
Wood base - Qty. 1
Parts List:
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
QRS
1/2" Bolt
Qty. 29
Optional glides
Qty. 4
Washers
Qty. 33
Glass door guides
Qty. 2
Adhesive door handles
Qty. 2
Shelf Rests
w/washer & bolt
Qty. 20
Wood screws
Qty. 2
Nuts
Qty. 2
Upper door track
Qty. 1
Lower door track
Qty. 1
"M" bracket
Qty. 4
"L" bracket
Qty. 8
Door lock kit
Qty. 1
AF
M
N
O
P
B
GHIJ
C D
K
E
L
Optional - attach glides (J) to bottom of base
before starting glass panel assembly.

FRAMELESS GLASS WALL UNIT
#16522
PAGE 3 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
OPTIONAL
Turn base over so bottom is facing up. Using a rubber mallet,
add glides (J) to each corner of the base. Once glides are in
place, turn base right side up to start with STEP 1.
It is recommended two people assist with the assembly of this unit.
STEP 1
Install bottom door track (M) onto top of base (P).
Look for 2 small drill holes along front edge of base. (Fig. 1a) Note, drill holes are offset on purpose.
Begin by sliding the center section of door track (M) to the right, this will reveal screw hole. Position track so screw hole aligns
with pre-drilled hole in the wood base. (Fig. 1b)
Use wood screw (K) to attach lower track. Do NOT fully tighten screw until BOTH screws are in place.
Once screw is in place on left side, slide center track to the left, to reveal the screw hole on the right end of the track.
Position so screw hole aligns with pre-drilled hole in the wood base and add remaining wood screw. (Fig. 1c)
Once BOTH screws are in place, you may tighten them all the way down.
(Fig. 1c)(Fig. 1b)
(Fig. 1a)
Left screw
hole
Right screw
hole
J

STEP 2
Using pre-grooved slots on base, join one side panel (Q) and the back panel (R) at a 90 degree angle and secure with two
"L" brackets (B) along the vertical corner. Do not use the top or bottom holes on either panel. They will be used later in the
process.
Place "L" bracket (B) on the inside of glass panels and align with holes. Insert 1/2" bolt (I) through washer (H) through
pre-drilled hole from the outside of the glass. (Fig. 3) Once bolt is through glass, screw into bracket (B).
FRAMELESS GLASS WALL UNIT
#16522
PAGE 4 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
P
B
B
(Fig. 2)
H
I
Q
R

FRAMELESS GLASS WALL UNIT
#16522
PAGE 5 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
STEP 3
Repeat STEP 2 to add other side panel.
Place "L" bracket (B) on the inside of glass panels and align with holes.
Insert 1/2" bolt (I) through washer (H) then through pre-drilled hole from the outside of the glass. (Fig. 4) Once bolt is through
glass, screw into bracket (B).
(Fig. 3)
H
I
B
B

FRAMELESS GLASS WALL UNIT
#16522
PAGE 6 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
STEP 4
Secure glass panels to wood base.
At front of showcase, use "L" bracket (B) on the inside
of glass panel and align with hole in glass. Insert 1/2"
bolt (I) through washer (H) then through pre-drilled
hole from the outside of the glass and screw into top of
bracket (B). (Fig. 4).
Next, align hole in bottom of bracket (B) with pre-drilled
hole in base, making make sure it is level and straight
with base. Insert bolt through washer and screw into
base. Do not fully tighten bolts into base until all four
corners are in place and partially screwed in.
At rear of showcase, use "M" bracket (A) on the inside
of the glass panel and align with holes in glass. Insert
1/2" bolts (I) through washers (H) then through pre-
drilled hole from the outside of the glass and screw into
top of bracket (B).
Next, align hole in bottom of bracket (A) with pre-drilled
hole in base, making make sure it is level and straight
with base. Insert bolt through washer and screw into
base.
Repeat step 4 for locations on the opposite side of the
wood base.
(Fig. 4)
B
HH
I
I
B
M

FRAMELESS GLASS WALL UNIT
#16522
PAGE 7 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
Next, Place an "L" bracket (B) on the inside of each glass side panel using holes on top glass and side
glass, closest to the sliding doors. Insert 1/2" bolt (I) through washer (H) then through pre-drilled hole
from the outside of the glass.
Repeat the above step for the other side panel to secure top glass in place.
STEP 6
Attach top to sides and front.
Attach "M" bracket (A) to each corner
at the back of the tower. Insert 1/2" bolt
(I) through washer (H) then through
pre-drilled holes on each side from the
outside of the glass.
B
A
BA
H
N
H
STEP 5
Install upper door track to top glass panel prior to attaching top panel to wall unit.
Align holes in the upper track (L) with pre-drilled holes in the top glass. Insert 1/2" bolt (I) through washer (H) then through
pre-drilled hole from the outside of the glass. Once bolt is through glass and metal track, add nut (G) to end of bolt. Do not
fully tighten nut until both ends of track are attached to glass.
L
H
G
I
I
I

FRAMELESS GLASS WALL UNIT
#16522
PAGE 8 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
O
STEP 7
Shelf supports and shelves
Side and back glass panels have pre-drilled holes for shelving. Double holes are provided so shelf heights can be adjusted
based on needs. Determine which level you want each shelf, then install shelf rest (F) on all three glass panels.
To install shelf rests, unscrew bolt and washer from end of shelf rest. Insert bolt and washer from outside of glass into shelf
rest (barrel shaped post) positioned on the inside of the glass panel.
Repeat these steps for all eight locations.
Once shelf rests (F) are in place, add shelves.
F FF

STEP 8
Sliding doors and lock.
The left door is pre-drilled for installation of a plunger lock.
Locate screw holes on back of metal plate and insert lock (E) so faceplate aligns with holes. Attach with two 1/4" at head
screws from the door lock kit. Once attached, slide silver ring over plunger (on front side of door) and press into place.
Door frontDoor back
FRAMELESS GLASS WALL UNIT
#16522
PAGE 9 OF 10
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
SS
E
STEP 9
Rotate door panel 180 degrees and place plastic
door guide (C) on the top of each door. Center each
door guide in the middle of the door.
C
BOTTOM
TOP
LEFT DOOR RIGHT DOOR

FRAMELESS GLASS WALL UNIT
#16522
PAGE 10 OF 10
WWW.KC-STORE-FIXTURES.COM
7400 E. 12TH STREET, KANSAS CITY, MO 64126 • 1-800-
STEP 10
Install Right door rst. Position top of right door into top door track (L) using the track furthest back.
Once top of door is in the track, keep door lifted slightly and position wheels on back rail of lower door track (M).
Back track
Front track
L
STEP 11
Install left door (with lock) last. Once the right side door is in place, position top of left door into top door track
using the closest (front) track. Make sure the key side of the lock is facing out towards you. Once top of door
is in the track, keep door lifted slightly and position wheels on front rail of lower door track. With plunger lock in
open position, both doors should now slide smoothly, left to right past each other.
STEP 12
Once doors are in place, attach adhesive door pulls (D) on outside of each door,
approx. 4" in from edge. You may select the height based on your personal
preference.
Back rail
Right
door in
place on
back,
bottom
track
Front rail M
D