KC STORE FIXTURES 16525 User manual

FRAMELESS GLASS CORNER UNIT
#16525
PAGE 1 OF 8
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899

FRAMELESS GLASS CORNER UNIT
#16525
PAGE 2 OF 8
Screws for lock
Qty. 2
Wood screws
Qty. 3
7/8" Bolt
Qty. 16
1/2" Bolt
Qty. 12
Nuts
Qty. 4
Plastic tube
Qty. 16
Plastic sleeves
Qty. 28
Glass shelves
Qty. 2
Glass top
Qty. 1
Glass sides
Qty. 2
Glass back
Qty. 2
Glass door
Qty. 1
Wood base
Qty. 1
Parts List:
"M" bracket
Qty. 3
"L" bracket
Qty. 12
Door hinges
Qty. 2
Door stop & screw
Qty. 1
Door lock
Qty. 1
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
A
F
M
N
O
Q RP
B
GHIJ
C D
K
E
L

Place wood base on a level surface.
STEP 1
The base is pre-grooved for back and side panels. Set the two back
panels (Q) into the grooves at a 90 degree angle.
Attach the two panels using two "L" brackets (B) along the vertical corner.
Place an "L" bracket (B) on the inside of glass panels and align with
holes. Insert 7/8" bolt (I) into plastic sleeve (H) then slide both through
pre-drilled hole from the outside of the glass (Fig. 1).
Screw bolt through bracket and slide plastic tube (F) over end of bolt.
Repeat this for each of the "L" brackets.
STEP 2
Attach back glass panels to the base, using four "L" brackets on the inside
of the glass panel and align with holes at bottom of each panel. Insert 1/2"
bolt (J) into plastic sleeve (H) then slide both through pre-drilled hole from
the outside of the glass and screw into top hole of bracket (Fig. 2).
Repeat step 2 for all four brackets along the bottom, using only the top
hole. DO NOT attach bracket to wood base until side glass panels have
been installed (STEP 4).
FRAMELESS GLASS CORNER UNIT
#16525
PAGE 3 OF 8
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
O
B
(Fig. 1)
FH
I
H
J
(Fig. 2)
B
Q

FRAMELESS GLASS CORNER UNIT
#16525
PAGE 4 OF 8
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
STEP 3
Insert side panels (P) into grooves on wood base.
Connect corners where side panel meets back glass panels using four "L"
brackets. Place "L" bracket (B) on the inside of glass panels and align with
holes. Insert 7/8" bolt (I) into plastic sleeve (H) then slide both through pre-
drilled hole from the outside of the glass (Fig. 3).
Screw bolt through bracket and slide plastic tube (F) over end of bolt.
Repeat this for each of the "L" brackets.
(Fig. 3)
FH
I
P
P
L
(Fig. 4)
B
STEP 4
After side glass panels are in place, secure the "L" brackets to the wood
base using wood screws (Fig. 4). If using a power drill, be careful not to
over tighten.
Repeat this step for bracket in opposite corner.
"L" brackets located in the back corner will overlap each other.
One screw will be used to connect both brackets to the base.

FRAMELESS GLASS CORNER UNIT
#16525
PAGE 5 OF 8
www.kc-store-xtures.com
7400 E. 12th Street, Kansas City, MO 64126 • 1-800-862-0899
STEP 5
Along the front edge of each side panel are two pre-drilled holes for shelving.
In each hole, insert a 7/8" bolt (I) and plastic sleeve (H) through the hole from
the outside. Once through the hole, add a nut (G) and tighten. Slide a plastic
tube (F) over the end of the bolt (Fig. 5).
Repeat this steps for all four locations.
H
(Fig. 5)
G
iF
STEP 6
Place "L" bracket (B) on the inside, top of each glass side panel.
Insert 1/2" bolt (J) into plastic sleeve (H) and slide both through pre-drilled
hole from the outside of the glass. Screw into bracket hole (Fig. 6).
B
H
J
(Fig. 6)