Kenwood CM470 series User manual

key
water filter
water filter holder
removable water tank
lid
compartment for excess cord
hotplate (model CM470 series only)
anti drip activating device
program button
clock button
on/off button with indicator light
glass carafe and lid
(model CM470 series only)
thermal carafe and lid
(model CM480 series only)
measuring spoon
filter holder
permanent coffee filter (or use a
paper filter instead)
lid opening lip
aroma control
cup storage area
to make coffee
1Lift the lid.
2Lift out the water tank from the
coffee maker.
3Separate the water filter holder by
pulling the unit apart and place the
water filter inside. Fit the unit back
together.
4Turn the handle on the water filter
holder and align the arrow on the
base with the letter for the current
corresponding month eg F for
February.
5Lower the water filter holder into
the water tank and fit into position
in the recess.
6Fill the tank with the desired
amount of water. The water must
be between the top and bottom
cup marks. Do not fill above the
MAX level. (Alternatively fill the
water tank when fitted inside the
coffee maker but take care not to
cause spillage.)
●Use cold water. We recommend
using filtered water from a
Kenwood Water Filter as it
reduces limescale. Never use
warm or fizzy water.
7Replace the water tank back into
the coffee maker.
8Ensure the filter holder is in
position in the coffee maker.
9Fit either the permanent filter
supplied or a paper filter into the
filter holder. Add the coffee, use
the spoon provided (approximately
1 level spoon per cup or to taste).
10 Close the lid and adjust the aroma
control as required. Turn the
control to the left for stronger
coffee and to the right for weaker
coffee.
11 CM470 series
●Put the carafe on the hotplate.
CM480 series
To achieve the best performance,
rinse the thermal carafe with hot
water immediately before switching
on the coffee maker.
●Screw the lid onto the thermal
carafe. For brewing, the lid should
be fully closed with the tab on the
lid in line with the carafe handle.
Put the carafe on the base.
12 Plug into the power supply and
press the on/off button.
13 Press the on/off button twice to
start brewing immediately. The
on/off button will glow and the
coffee maker will start to operate.
The back light of the display will
come on and automatically switch
off after 10 minutes.
To stop the brewing process at
any time, press the on/off button.
The back light of the display will
come on for one minute and then
go off automatically.
14 Don’t remove the carafe until
brewing has finished.
safety
●Watch out for steam, never lift the
tank lid during the brewing cycle.
●CM470 series only: never
touch the hotplate.
●Always lift the lid using the lid
opening lip.
●Don’t touch hot parts including
the cup storage area.
●Keep children away from the
machine. And never let the cord
hang down where a child could
grab it. Push excess cord inside
the back of the machine.
●Never use a damaged machine.
Get it checked or repaired: see
‘service and customer care’.
●Never put the machine in water or
let the cord or plug get wet - you
could get an electric shock.
●Unplug:
●●before filling with water
●●before cleaning
●●after use.
●Never leave the machine on
unattended.
●Don’t let the cord touch hot parts.
●Always make sure there is water in
the tank before switching on.
●This coffee maker is only suitable
for use with the type of carafe
supplied.
●This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of
the appliance by a person
responsible for their safety.
●Children should be supervised to
ensure that they do not play with
the appliance.
●Only use the appliance for its
intended domestic use. Kenwood
will not accept any liability if the
appliance is subject to improper
use, or failure to comply with these
instructions.
before plugging in
Make sure your electricity supply is
the same as the one shown on the
underside of your machine.
Important (UK) only
●The wires in the cord are coloured
as follows:
Green and Yellow = Earth
Blue = Neutral
Brown = Live.
●The appliance must be protected
by a 13A approved (BS1362) fuse.
●WARNING: THIS APPLIANCE
MUST BE EARTHED.
Note:
●For non-rewireable plugs the fuse
cover MUST be refitted when
replacing the fuse. If the fuse
cover is lost then the plug must
not be used until a replacement
can be obtained. The correct fuse
cover is identified by colour and a
replacement may be obtained
from your Kenwood Authorised
Repairer (see Service).
●If a non-rewireable plug is cut off it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise if an unwanted
non-rewireable plug is
inadvertently inserted into a 13A
socket outlet.
●This machine complies with
European Economic Community
Directive 89/336/EEC.
before using for the first
time
1Remove all packaging.
2Wash the parts: see ‘care and
cleaning’.
3Push excess cord inside the back
of the machine.
4Run two lots of water through the
machine (without coffee) to clean it
out. Fill the tank to the top cup
mark when you do this. See ‘to
make coffee’.
6
9
10
15
12
18
2
3
4
6
6
9
8
12
10
15
12
18



















Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK
www.kenwoodworld.com 56087/3
CM470 series
CM480 series
CM470 series
●The hot plate will keep your coffee
hot, but the sooner you drink it,
the better it will taste.
●Your coffee maker will keep the
coffee warm and then
automatically switch off after 2
hours. To manually switch off
earlier, press the on/off button.
CM480 series
●To pour coffee after brewing has
finished, unscrew the lid 180° so
that the tab on the lid is in line
with the pouring spout. Once the
desired amount of coffee has
been poured, screw the lid back
on to best retain the coffee
temperature.
●As soon as all the coffee has
brewed, switch off and unplug the
machine.
●If you haven’t used the machine
for a while, run one lot of water
through it (without coffee) to clean
it out. Fill the water tank to the top
cup mark when you do this.
●Never put the carafe in the
microwave.
to set the clock
1Plug in the coffee maker, the
backlight will come on and the
display will flash.
2Select the correct time of day by
pressing the clock button once
and the time will advance by 1
minute. Press and hold down the
button and the time will advance
in 15 minute intervals.
●If required, press the program
button once to change between
the 12 and 24 hour clock.
3To set the clock press the on/off
button or wait 1 minute for it to
automatically set.
●To re-adjust the clock at any time,
press and hold the clock button
for 5 seconds and adjust the
clock as above.
Note – the backlight of the display
will automatically turn off after 1
minute.
to program automatic brew
1Set the clock to the correct time
(see ‘to set the clock’).
2Press the program button, the
clock symbol and the display will
flash.
3Press the clock button until the
desired brewing time is displayed
(follow procedure in ‘to set the
clock’).
4Press the on/off button to confirm
the automatic time selected. (The
display panel and the on/off
indicator light will flash).
5Press the program button to
return to the current time of day
(the on/off button will continue to
flash). The brewing cycle will begin
once the set time is reached and
the on/off button will stop flashing.
●If you want to check the automatic
time selected, press the program
button.
●To override the automatic brewing
operation press the on/off button
and the coffee maker will start
immediately. Press the button
again to switch off.
care & cleaning
●Always switch off, unplug and
allow to cool before cleaning.
●Never put the machine in water or
let the cord or plug get wet.
●Don’t wash parts in the
dishwasher.
water filter
●Change and discard the water
filter after 70 brewing operations
or within a calender month
whichever is sooner.
carafe, lid, permanent filter,
filter holder, water filter
holder
●Wash, then dry.
body
●Wipe with a damp cloth, then dry.
Don’t use abrasives - they’ll
scratch the plastic and metal
surfaces.
descaling
With use, the display will indicate
when the coffee maker requires
descaling. A series of solid lines
will gradually appear and when 4
appear in the display and flash ,
the coffee maker has
completed 100 cycles or more
and requires descaling (see ‘to
descale’).
important
When descaling always remove
the water filter and water filter
holder first.
to descale
1Buy a suitable descaler.
2Descale the machine.
3After descaling, run several lots of
water through the machine to
clean it out. Fill the tank to the top
cup mark when you do this.
4Wash the parts.
5To reset the descale counter to
zero, press the clock and program
button at the same time for 2
seconds.
service and customer
care
●If the cord is damaged it must, for
safety reasons, be replaced by
Kenwood or an authorised
Kenwood repairer.
UK
If you need help with:
●using your machine or
●servicing, spare parts or repairs (in
or out of guarantee)
call Kenwood customer care on
023 92392333. Have your
model number ready - it’s on
the underside of the coffee maker.
For spare parts including water
filters call 0870 241 3653.
●other countries
Contact the shop where you
bought your machine.
guarantee
If your coffee maker goes wrong
within one year from the date you
bought it, we will repair it (or
replace it if necessary) free of
charge provided:
●you have not misused, neglected
or damaged it;
●it has not been modified (unless by
Kenwood);
●it is not second-hand;
●it has not been used
commercially;
●you have not fitted a plug
incorrectly; and
●you supply your receipt to
show when you bought it.
This guarantee does not affect
your statutory rights.
2
3
4
6
6
9
8
12
10
15
12
18
2
3
4
6
6
9
8
12
10
15
12
18