Kestrel 1000 User manual

USER GUIDE
1000, 2000, 2500 & 2500NV,
3000, 3500 & 3500NV, 3500DT
kestrelinstruments.com

3
CONTENTS
Features & Options ....................................................4
Getting to Know Your Kestrel..................................5
Getting Started...........................................................6
Setup + Options .........................................................6
Barometric Pressure & Altitude Adjustment........7
Measurement Notes..................................................8
Maintenance & Service .............................................9
Sensor Calibration ...................................................10
Warranty ....................................................................11
For instruction manuals for all Kestrel
products, FAQs, technical support,
instructional videos and more, please
visit:www.kestrelinstruments.com/help
or contact us at [phone]
[email protected][phone]www.lazodecontrol.com

4
Measurement Icon Hint Units of Measure 1000 2000 2500 3000 3500 3500DT
Wind Speed SPd mph |kt |B |m/s |ft/min |km/h • • • • • •
Temperature dEG ˚F |˚C • • • • •
Wind Chill chill ˚F |˚C • • • •
Relative Humidity % r.h. % • • •
Heat Stress Index % H.I ˚F |˚C • •
Dewpoint Temp d . P. ˚F |˚C • • •
Barometric Pressure bAro inHg |hPA |mb •• •
Altitude Alt m |ft •• •
Wet Bulb Temp bulb ˚F |˚C • •
Backlit Display • • • • •
Pressure Trend ••
Delta T dElt •
Clock •••
*The NV series features a dim red backlight for use in low light or nighttime situations.
*Only one arrow icon will be displayed on screen to indicate the 3-hour pressure trend.
FEATURES & OPTIONS
The table below shows all Measurement screens available, listed with their
corresponding screen icon and “Hint” abbreviation.
[email protected][phone]www.lazodecontrol.com

5
3000
Nielsen Kellerman
www.nkhome.com
[email protected]
610.447.1555
US Patents
5,783,753
5,939,645
REPLACEABLE
IMPELLER
PRESSURE
SENSOR
SERIAL
NUMBER
NAVIGATION
BUTTONS
POWER/BACKLIGHT
BUTTON
(Backlight N/A on K1000)
TEMPERATURE
THERMISTOR
(N/A on K1000)
FRONT
BATTERY DOOR:
CR2032 COIN CELL
BACK
*All Kestrel Meters with temperature measurement allow you to measure air, water and snow temperature.
HUMIDITY
SENSOR
GETTING TO KNOW YOUR KESTREL
[email protected][phone]www.lazodecontrol.com

6
Turning ON and OFFxx
• Press to turn on.
• Hold for 3 seconds to turn o.
The Kestrel Meter will automatically turn o if no buttons
have been pressed for 45 minutes.
Select Measurement Mode
• Use or to access each Measurement screen
• The instantaneous Measurement value will be
displayed on each screen and updated once per
second.
Each Measurement screen will ash a brief “Hint” to clarify
which Measurement is being displayed. Note: Hints are not
displayed in the Kestrel 1000.
The Measurement’s icons and units of measure will be
displayed in the lower line of the screen.
75.2
°F °F
Temperature “Hint”
ashes before
Temperature
Measurement Screen
Select the Unit of Measure
• Select the unit of measure. While holding ,
press to scroll through the available units
of measure for that measurement.
Adjust the Clock
*This applies to the 2500, 2500NV, 3500, 3500NV and 3500DT.
• Adjust the clock. Simultaneously press and
to access clock setting. While the time is
blinking, press or to change the time.
Hold either button down to adjust quickly.
Simultaneously press and to exit clock
setting.
GETTING STARTED SETUP + OPTIONS
[email protected][phone]www.lazodecontrol.com

7
SETTING REFERENCE BAROMETRIC PRESSURE &
ALTITUDE: KESTREL 2500 & KESTREL 3500 ONLY
The Kestrel Meter measures “station pressure,” which changes
in response to both changes in altitude and changes in
atmosphere. Barometric pressure is a measurement of the air
pressure adjusted to sea level. To obtain accurate barometric
pressure and altitude readings, you must rst enter EITHER
your location’s current barometric pressure OR your current
altitude.
*Station pressure is displayed if the reference altitude is set to zero.
Starting with Known Altitude for your Location
• Use or to highlight the “BARO” screen.
• Press and simultaneously until the word
“REF” starts blinking on screen.
• Use or to adjust the value to the correct
known Altitude.
• Press and simultaneously to exit the
reference setting mode.
After the Altitude reference is set, place the unit on a table and
allow it to stabilize. The accurate Barometric Pressure reading will
then be displayed on screen.
Note the correct barometric pressure reading above
and use this measurement to set the Altitude:
• Use or to highlight the “Altitude” screen.
• Press and simultaneously until the word
“REF” starts blinking on screen.
• Use or to adjust the value to the barometric
pressure measurement noted above.
• Press and simultaneously again to exit the
setting mode.
Starting with Known Barometric Pressure for
your Location
• Use or to highlight the “Altitude”
screen.
• Press and simultaneously until the
word “REF” starts blinking on screen.
• Use or to adjust the reference value to
the correct known Barometric Pressure.
• Press and simultaneously again to exit
the setting mode.
After the Pressure reference is set, place the unit on a table
and allow it to stabilize. The accurate Altitude reading will
then be displayed on screen.
Note the correct altitude reading above and
use this to set the Barometric Pressure:
• Use or to highlight the “BARO” screen.
• Press and simultaneously until the
word “REF” starts blinking on screen.
• Use or to adjust the reference value to
the correct known Altitude.
• Press and simultaneously again to exit
the setting mode.
Once these steps are complete, both screens will
display accurate readings.
*Be sure to adjust your reference measurements when
you change your location for altitude and/or barometric
pressure or when there has been dramatic change in
weather conditions.
BAROMETRIC PRESSURE & ALTITUDE ADJUSTMENT
[email protected][phone]www.lazodecontrol.com

8
Max/Avg Function
To view the maximum wind gust recorded, press
or until you see “MAX” appear at bottom
of screen. Press again to view average wind gust.
“AVG” will appear at bottom of screen. Both Max
and Average are reset each time the unit is powered
down. To restart averaging, simply turn the unit o
and back on again.
Hold Mode
Hold Mode can be useful for taking measurements when you
are unable to view the display.
• Hold down , then press .
• The word“HOLD”will blink on each screen and all
values will stop measuring and freeze in memory.
• Use or to view each Measurement screen in
Hold Mode.
• To exit Hold Mode, hold down , then press
again.
Backlight*
• Press to activate the backlight for 10 seconds.
• Press again to manually deactivate the backlight
before 10 seconds expire.
*The Kestrel 1000 Meter does NOT oer a backlight.
MEASUREMENTS
Barometric Pressure Trend
: indicates pressure is rising quickly (> +0.18 inHg) in 3 hours
: indicates pressure is rising (within +0.06 and +0.18 inHg)
: indicates pressure is stable (remains between -0.06 and +0.06
inHg)
: indicates pressure is dropping (within -0.06 and -0.18 inHg)
: indicates pressure is falling quickly (> -0.18 inHg)
Select Units of Measure
• Use or to scroll to the desired
Measurement screen.
• Hold down , then press to set the desired
Units of Measure for the Measurement.
Water and Snow Temperature
The Kestrel Meter may also be used to measure
the temperature of water and snow. Submerge the
thermistor portion (curly exposed wire in window
next to impeller) in water or snow to get an accurate
reading. Kestrel Meters are completely waterproof,
oat and can be safely submerged in water
according to IP-67 standards (up to 1 meter for a
maximum of 30 minutes).
MEASUREMENT NOTES
[email protected][phone]www.lazodecontrol.com

9
Replacing the Battery
When your display becomes dim or disappears, you need
to change the battery.
Use a US nickel or similar coin to twist open the battery
compartment.
Replace battery with a new, clean CR2032 coin-cell
battery, with positive side (+) facing up.
CR2032 batteries are available in most stores that sell
batteries.
When replacing the battery door, be sure to keep the black rubber
o-ring seated in the groove on the case back.
MAINTENANCE & SERVICE ADDENDUM
[email protected][phone]www.lazodecontrol.com

10
Impeller
The Kestrel impeller calibration drift is less than
1% after 100 hours of use at 16 MPH | 7 m/s. Drift
increases with higher-speed use. For most users, the
impeller will provide accurate wind speed/air ow
readings for years if not physically damaged. How-
ever, if your application requires extremely high
precision or if you perform frequent high-speed
readings, we recommend you replace your impeller
at one-year intervals. Every replacement impel-
ler is supplied with a certicate of conformity and
restores your Kestrel’s calibration upon installation.
Temperature Sensor (Kestrel 2000 and higher)
The Kestrel temperature sensor exhibits virtually
zero drift over time and generally does not require
recalibration for accurate performance during the
life of the product. If your industry or application
requires calibration, please contact NK or a certied
calibration lab for options and pricing.
Humidity Sensor (Kestrel 3000 and higher)
The Kestrel humidity sensor calibration drift may
be up to +/- 2% over 24 months. For high-precision
applications, we recommend recalibration at
24-month intervals. If you require calibration,
please contact NK or a certied calibration lab for
options and pricing. The humidity sensor may also
be recalibrated in the eld using a Kestrel Humid-
ity Calibration Kit (NK PN-0802). Instructions for
running the recalibration routine are provided with
the Humidity Calibration Kit and may also be found
at www.kestrelinstruments.com/mwdownloads/
download/link/id/37/
Pressure Sensor (Kestrel 2500 & 3500)
The Kestrel pressure sensor drift may be up to 1
mbar over 12 months. For high-precision applica-
tions, we recommend recalibration at 12-month in-
tervals. If you require calibration, please contact NK
or a certied calibration lab for options and pricing.
The pressure sensor may also be recalibrated in the
eld with reference to a known-accurate and cali-
brated pressure standard. We do not recommend
simply recalibrating to a local weather station as this
may not be accurate for your location. Instructions
for recalibrating the pressure sensor may be found
at www.kestrelinstruments.com/category-ser-
vice-calibration/kestrel-calibration.
SENSOR CALIBRATION
[e-mail][phone]www.lazodecontrol.com [email protected][phone]www.lazodecontrol.com
Automatización y Medio Ambiente
www.lazodecontrol.com

[email protected]
Jr.Salaverry 160 – Magdalena
[phone]

11
Your Kestrel instrument is warrantied to be free of defects in materials and workmanship for a period of FIVE
YEARS from the date of its rst consumer purchase. NK will repair or replace any defective product or part when
notied within the warranty period, and will return the product via domestic ground shipping or NK’s choice
of method of international shipping at no charge. The following are excluded from warranty coverage: damage
due to improper use, storage, maintenance or handling (including corrosion); damage caused by severe or
excessive impact, damage caused by failed or leaking batteries, crushing or mechanical harm; modications
or attempted repairs by someone other than an authorized NK repair agent; impeller failure not caused by a
manufacturing defect; normal usage wear and failed batteries. Measurement accuracy is warranted to be within
the specications on the supplied Certicate of Conformity including specied drift since date of manufacture.
If no warranty registration or proof of purchase is provided, the warranty period will be measured from the
product’s date of manufacture.
Except for the warranties set forth herein, NK disclaims all other warranties, expressed, implied or
statutory, including, but not limited to, the implied warranties of merchantability or tness for a
particular purpose. Any implied warranties that may be imposed by applicable law are limited to the
term of this warranty. In no event shall NK be liable for any incidental, special or consequential damages,
including, but not limited to, loss of business, loss of prots, loss of data or use, whether in an action
in contract or tort or based on a warranty, arising out of or in connection with the use or recalibration,
performance of an NK product, even if NK has been advised of the possibility of
such damages. You agree that repair, and (upon availability) replacement, as applicable, is
your sole and exclusive remedy with respect to any breach of the NK Limited Warranty
set forth herein.
All product liability and warranty options are governed exclusively by the laws of the
Commonwealth of Pennsylvania.
Please register your Kestrel instrument at www.kestrelinstruments.com
5 YEAR LIMITED WARRANTY
[email protected][phone]www.lazodecontrol.com