Keurig DRINKWORKS Home Bar User manual

HOME BAR CARE GUIDE
Bar quality drinks
at the touch of a button.
Cheers!

drinkworks.com
Drinkmaker warnings.
Read and follow all warnings and instructions before use.
Misuse of this drinkmaker may result in serious personal injury or property damage.
Positioning
Set up the drinkmaker on a flat, weight-
bearing, stable, heat-resistant surface
away from hot surfaces, sources of heat,
or open flames.
Keep out of reach of children.
Keep upright. Do not use the drinkmaker
unless it is in its upright position.
Use
Use only with Drinkworks™ Pods. Use with
any other Pod may result in injury or damage
to the unit.
Use only water in this drinkmaker. Do not
put any other liquids or substances in the
water tank except as instructed in the
Cleaning Instructions.
Do not overfill the water tank.
Do not move the drinkmaker during the
beverage making process.
Drinkmaker operating temperature between
41°F to 86°F (5°C to 30°C).
You must be 21 years or older to purchase or
consume alcoholic beverages.
i
Care
Perform maintenance only as directed in
the Home Bar Care Guide.
Always drain the drinkmaker before
unplugging.
Any servicing other than cleaning and user
maintenance should be performed by a
Drinkworks™ authorized representative.
Attempting other maintenance or servicing
could cause injury or damage.
Disposal
The symbol on the product or its packaging
indicates: Do not dispose of electrical
appliances or batteries as unsorted municipal
waste, use separate collection facilities.
Contact your local authority for information
regarding the collection systems available.
If electrical appliances are disposed of in
landfills or dumps, hazardous substances
can leak into the groundwater and get into
the food chain, damaging your health and
well-being.
Please contact your local or regional waste
authority for more information on collection,
reuse and recycling programs.
Welcome.
We recommend that you review and carefully follow
this guide as well as all warnings and instructions that
accompanied your drinkmaker to make the most of
your Drinkworks™ Home Bar. This guide includes use,
care, maintenance, and troubleshooting information
for you to keep making remarkable drinks every time.

ii
Carbonation warnings.
System contains CO2gas under pressure. Do not puncture CO2Cartridge or expose to heat,
fire, or flame. Inspect for any dents, puncture, or damage before use, and do not use if damaged.
Keep out of reach of children. Close supervision is necessary when the drinkmaker is used
near children.
Handling
Mishandling the CO2Cartridge can result in
serious personal injury.
Do not throw or drop the CO2Cartridge or
allow it to fall.
Do not tamper with the CO2Cartridge in
any way.
Do not transport the drinkmaker with the
CO2Cartridge installed in the drinkmaker.
Do not heat CO2Cartridge or leave in
direct sunlight.
Do not inhale CO2.
Store CO2Cartridge in a well-ventilated cool
and dry place (Max. 50°C/122°F).
Do not handle the CO2Cartridge while
discharging remaining CO2by pressing the
blue CO2Gas Release Button. CO2Cartridge
will be extremely cold and could freeze tissue.
Allow CO2Cartridge to warm up to room
temperature before handling.
Carbonation
Do not allow children to use the drinkmaker.
Use only authorized Drinkworks™ CO2
Cartridges. Use of non-authorized CO2
Cartridges could lead to serious injury
or damage.
Do not remove the CO2Cartridge from the
machine until all the CO2has been discharged
from the Cartridge.
The blue CO2Gas Release Button must
be depressed to release any remaining gas
before removing the CO2Cartridge from
the drinkmaker.
Removing CO2Cartridge before discharging
all CO2could cause injury.
Use
Inspect the CO2Cartridge before use for
dents, punctures, or other damage.
If you see any, do not use the Cartridge,
contact a Drinkworks™ representative.
Do not open CO2Door while drinkmaker is
preparing beverage.
End of Life
Do not attempt to refill. Empty CO2Cartridge
are not refillable.
Electrical warnings.
When using electrical appliances, basic safety precautions should be followed,
including the following:
General
Read all instructions before using.
This drinkmaker must be properly installed
and located in accordance with these
instructions before it is used.
Clean component parts as specified in the
Home Bar Care Guide.
Always keep the water tank cover on the
Water Tank unless you are refilling it.
Do not attempt to lift the drinkmaker handle
while making a beverage.
To protect against fire, electrical shock,
and injury do not immerse cords, plugs, or
the drinkmaker in water or other liquids.
Do not use the drinkmaker for other than its
intended use.
The use of non-authorized accessories may
cause injuries or damage the drinkmaker.
Positioning
Ensure that sufficient space is left
around all sides of the drinkmaker to allow
air to circulate.
Do not obstruct the vents on the sides and
rear of the drinkmaker.
iii
Do not place on or near a hot gas or electric
burner, or in a heated oven.
Keep your drinkmaker away from direct
sunlight and heat sources.
Do not use outdoors. The drinkmaker is
intended for indoor use only.
Do not let the cord hang over the edge of the
table or counter, or touch hot surfaces.
Use of accessory attachments are
not recommended by the drinkmaker
manufacturer and may result in fire, electrical
shock, or injury to persons.
Cords and Grounding
The drinkmaker is equipped with a power cord
having grounding wires with a grounding plug.
GROUNDING INSTRUCTIONS: This
drinkmaker must be grounded. In the event
of malfunction or breakdown, grounding
provides a path of least resistance for electric
current to reduce the risk of electric shock.
This drinkmaker is equipped with a cord having
an equipment-grounding conductor and a
grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed
and grounded in accordance with all local
codes and ordinances.

01iv
Figure 1
(A)
GROUNDING
PIN
Cords and Grounding (Cont.)
DANGER - Improper connection of the
equipment-grounding conductor can result
in a risk of electric shock. The conductor
with insulation having an outer surface that
is green with or without yellow stripes is the
equipment-grounding conductor. If repair or
replacement of the cord or plug is necessary,
do not connect the equipment-grounding
conductor to a live terminal. Check with a
qualified electrician or serviceman if the
grounding instructions are not completely
understood, or if in doubt as to whether the
drinkmaker is properly grounded. Do not
modify the plug provided with the drinkmaker
- if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This appliance is for use on a nominal 120 V
circuit, and has a grounding plug that looks like
the plug illustrated in sketch A in Figure 1.
SHORT CORD INSTRUCTIONS: A short power
supply cord is provided to reduce the risk
of becoming entangled in or tripping over a
longer cord. If an extension cord is used: (1)
the marked electrical rating of the cord set
or extension cord should be at least as great
as the electrical rating of the appliance, (2)
the cord should be arranged so that it will not
drape over a counter-top or table top where
it can be pulled on by children or tripped over
unintentionally, and (3) the extension cord
must include a 3-prong grounding plug.
EXTERNAL CLEANING: It is ideal that the
product is unplugged while cleaning the
exterior of the appliance.
WHEN UNPLUGGING POWER: To
disconnect, turn off power switch, then
remove plug from outlet.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Drinkmaker Warnings................................................................. i
Carbonation Warnings ............................................................... ii
Electrical Warnings .................................................................. iii
About Your Home Bar ................................................................ 02
Using Your Home Bar ................................................................. 03
Positioning the drinkmaker ........................................................ 03
Chilling ......................................................................... 04
Making a drink ................................................................... 05
Get connected .................................................................. 08
Tips For Pouring a Beer ............................................................... 09
Drinkmaker Controls & Menu Functions................................................. 10
Home Bar Care & Cleaning ............................................................ 12
CO2Cartridge Care & Replacement .................................................... 20
Drinkmaker Status ................................................................... 24
Troubleshooting ..................................................................... 25
Helpful Hints ........................................................................ 28
Home Bar Warranty .................................................................. 29
Contents:
THIS PRODUCT IS FOR
HOUSEHOLD USE ONLY.

02 03
Place your drinkmaker in an open, uncluttered area in your kitchen or bar area. Leave the
following distance around your drinkmaker:
At least 2 inches (5 centimeters) from any wall.
For the best performance of the drinkmaker’s cooling and cleaning features, we recommend that
you always keep your drinkmaker plugged in and powered on.
Always remove the Water Tank from the drinkmaker to fill the Water Tank. Do not bring the
drinkmaker to the sink to refill the Water Tank. Do not fill beyond the MAX Fill line. Using bottled or
filtered water is recommended, but optional.
FILL THE WATER TANK WITH WATER OR ICE WATER ONLY, EXCEPT AS OTHERWISE
INSTRUCTED DURING A CLEAN CYCLE.
Positioning the drinkmaker.
Using your Home Bar.
About your Home Bar.
A. Pod (Not Included)
B. Water Tank
C. Power Button
D. Power Cord
E. Display
F. Touch Arrow Buttons
G. START Button
H. Drip Tray
I. Pod Basket
J. Pod Door
K. Handle
L. Tap
M. CO2Side Door
N. CO2Gas Release Button
O. CO2Cartridge
P. Half-Gallon Container (Not Included)
Q. Water Filter
K.
I.
A.
G.
J.
L.
N.
E.
F.
D. B.
C.
O.
M. Q.
P.
H.

04 05
3. Place a Drinkworks™ Pod into the Pod Basket. Make sure
that the Pod is fully inserted with the barcode on the Pod
label at 12 o’clock position – facing away from you.
2. Lift up the Handle on the Pod Door to reveal the
Pod Basket.
1. Fill the Water Tank as instructed by the Display.
Making a drink.
Your drinkmaker will chill water to 35º F in an
internal reservoir. The drinkmaker will begin
cooling the water as soon as you add water to
the Water Tank. Cooling water takes time; to
speed up this process, add ice to your Water
Tank before you add water. The Display will let
you know when the drinkmaker is cooling and
how long it will take before the internal reservoir
is fully chilled. To make drinks with carbonation,
the internal reservoir must be fully chilled. You
can make non-carbonated drinks at any time,
but it is recommended that you add ice to your
glass if the internal reservoir is still “Chilling…”
To avoid additional cooling time, we recommend
that you keep your drinkmaker plugged in and
powered on all the time.
NOTE: Make sure to empty the internal
reservoir before unplugging or powering
down your drinkmaker. You can do this by
running an Empty Cycle found on page 14.
Chilling…
Using your Home Bar.Using your Home Bar.
Internal Reservoir
35ºF
12 o’clock
Tip! When hosting a party or making lots of
drinks we recommend that you always keep
your Water Tank filled with ice, so you never
have to wait for a cold drink!

06 07
6. When the recipe is ready, the START Button will flash
blue. Press the START Button to make a drink!
NOTE: If you do not push the START Button within
60 seconds, the light will stop flashing blue. Re-load
the drink recipe by opening and closing the Pod Door
using the Handle.
5. Place appropriate sized glass underneath the Tap on top
of the Drip Tray. The Display will alert you to the correct
size glass to use based on the drink you have selected.
4. Close the Pod Door by pulling the Handle down. Wait for
drinkmaker to recognize your drink and prepare the recipe.
7. The Display will notify you when your drink is ready to
enjoy. Please enjoy responsibly!
NOTE: It is recommended that you remove the Pod from
your drinkmaker after your drink has been made.
XAM
XAM
Tip! Serving recommendations for each drink
including glassware, garnish, and ice can be
found on the Pod tube, Drinkworks™ App, or at
www.drinkworks.com.

08 09
For more information refer to the Drinkworks™ App
or visit the website www.drinkworks.com.For more information visit the website www.drinkworks.com.
3. Gradually straighten the glass to the upright position as
beer is dispensed from the Tap.
2. Hold the glass at a 45-degree angle to attain the right
combination of foam and liquid.
1. When making a beer, consider using a frosted glass. Give
the inside of your glass a quick rinse with cold water. This
will help sustain the head of the pour.
Get connected.
Your drinkmaker comes with built-in Bluetooth®Low Energy 4.2 technology. This technology
allows your drinkmaker to communicate with the Drinkworks™ App about its performance in
order to help us improve its function. Once connected to the Drinkworks™ App, you will have
a choice to opt in to share drinkmaker data with Drinkworks™ for these and other purposes
described during the opt-in process. This feature is optional. It is not required for the drinkmaker
to function properly.
Download the Drinkworks™ App from the Apple App Store or Google Play store for Android and
connect to your drinkmaker to enjoy all of the features offered by your drinkmaker.
After downloading the Drinkworks™ App, you can choose to get connected to your drinkmaker
with the following steps:
1. Enable the Bluetooth feature on your phone through its settings.
2. Create an account on the Drinkworks™ App and pair it with your drinkmaker by following
instructions on the initial Drinkworks™ App login.
3. Your drinkmaker will send a unique key for use with pairing the app that you must confirm
via the drinkmaker by pressing the Right Touch Arrow Button next to the Display panel.
4. Complete the Drinkworks™ App registration and ensure that your drinkmaker is paired
and connected by viewing the “Dashboard” in the Drinkworks™ App.
5. To disconnect from the drinkmaker’s Bluetooth®go to your phone settings and press
Forget Device.
What can I do with the Drinkworks™ App?
Setup and register your drinkmaker.
•Watch helpful videos.
•Send unique referral codes to friends and family.
•Access tips and answers to commonly asked questions.
•Shop for new beverage Pods and more!
Tips for pouring a beer.Using your Home Bar.
45°

10 11
Display Screen
Messages appear on the Display screen. Follow the prompts
on the screen to complete activities.
Solid Arrow
The Touch Arrow Buttons appear on either side of the Display.
Use them to move backwards and forwards through options.
Blinking Arrow
Touch a blinking arrow button to continue to the next step.
START Button
Press this button to confirm an action or select an option.
Arrows and START Button.
Drinkmaker controls.
*NOTE: These functions require the use of an empty half-gallon container that fits under the
Tap. The drinkmaker does not include this container. Any appropriately sized container can
be used for this purpose.
Menu options include:
Clean the drinkmaker* (requires Drinkworks™ Cleaning Tablets)
Rinse the drinkmaker*
Empty the drinkmaker* (required for storage)
Make a medium soda water (non-alcoholic)
Make a large soda water (non-alcoholic)
Change language to French or English
Exit the menu
To access the built-in drinkmaker functions, press and hold the START Button for 3 seconds.
Press the Touch Arrow Buttons on either side of the Display to move through the options.
Press the START Button to select your choice.
Accessing the drinkmaker menu.
Menu functions.

12 13
Home Bar care & cleaning.
CAUTION: Please rinse the Water Tank thoroughly after cleaning so that no cleaners
or cleaning solutions remain in this area as they may contaminate the water supply in
the drinkmaker.
1. Rinse the filter screen with the strong force of water
from your faucet.
2. If you have a sprayer, aim the water spray at the
filter screen.
3. Fill the Water Tank with approximately two inches of
clean water, close the Water Tank, and agitate (shake)
the Water Tank.
4. Empty the Water Tank then fill it with clean water and
return it to the drinkmaker. If needed, repeat the
above procedures.
Cleaning the Drinkmaker Exterior
Keep your drinkmaker looking its best by cleaning the exterior
after making drinks. Wipe down all the surfaces on your
drinkmaker with a clean, moist, lint-free, non-abrasive cloth.
Never immerse the drinkmaker in water or other liquids.
Cleaning the Drip Tray
The Drip Tray can accumulate up to 10 ounces of liquid before it
overflows. To remove the Drip Tray, slide it toward you, keeping
it level at all times to avoid spilling its contents. The Drip Tray
should occasionally be rinsed between cleanings. Clean the
Drip Tray with a damp, soapy, lint-free, non-abrasive cloth.
Cleaning the Pod Basket
Wash the Pod Basket at least once a week, but a quick rinse
after each drink is recommended—especially after making
flavorful cocktails*. The Pod Basket is removeable and can be
cleaned with a damp, soapy, lint-free, non-abrasive cloth or in
the top rack of the dishwasher. Keeping the Pod Basket clean
helps with drink quality.
*WARNING: Some beverage Pods may contain allergens such as milk, egg, wheat,
nuts, or soy, or have been produced in a facility that also produces products
containing milk, egg, wheat, nuts, or soy. Check the Pod packaging for allergen
information. If you make a drink with such a Pod, remove the Pod Basket and clean
it before your next drink, as there may be trace amounts of allergen on the basket.
Cleaning the Water Tank and Water Tank Lid
The Water Tank and Water Tank Lid should be periodically inspected and cleaned. Neither the
Water Tank or Water Tank Lid should be cleaned in the dishwasher. They should be cleaned with
a damp, soapy, lint-free, non-abrasive cloth and rinsed thoroughly. Do not dry the inside of the
Water Tank with a cloth as lint or other particles may transfer from the cloth to the Water Tank.
To clean the filter screen at the base of your Water Tank, empty the Water Tank and follow one
or all of the following procedures.
NOTE: If you are using a water filter inside the Water Tank, remove it before cleaning the Water
Tank. For water filter replacement, consult and follow the instructions and recommendations
on the filter package.
XAM

14 15
1. Initiate a Clean Cycle by selecting “RUN CLEAN CYCLE
PRESS START” from the drinkmaker menu by pressing the
START Button when that message is being displayed.
2. Remove and empty the Water Tank. If you are using a
water filter inside the Water Tank, remove it now.
3. Fill the Water Tank to the MAX fill line and replace it on
the drinkmaker.
Run the Rinse Cycle
Periodically run the drinkmaker Rinse Cycle. The Rinse Cycle empties and refills the internal
chilling tank so that drinks can be made with fresh water. Access the Rinse Cycle from the
drinkmaker Menu and follow the prompts on the Display. It takes about 10 minutes to complete
a Rinse Cycle.
NOTE: Please make sure to keep the Pod Basket in the drinkmaker while running a Rinse Cycle.
Run the Empty Cycle
Before you unplug or power down your drinkmaker, please make sure to run an Empty Cycle.
An Empty Cycle will drain the water from the Water Tank so that you can transport or store your
drinkmaker. Select “EMPTY DRINKMAKER PRESS START” from the drinkmaker’s menu and follow
the prompts on the Display using the arrow keys to navigate through the directions.
NOTE: Please make sure to keep the Pod Basket in the drinkmaker while running an
Empty Cycle.
Run the Clean Cycle
The drinkmaker has a pre-programmed
Clean Cycle and will indicate when it is
time to clean. To run a Clean Cycle, you will
need 3 Drinkworks™ Cleaning Tablets and a
container that can hold at least a half-gallon
of water to place under the Tap.
Run the Clean Cycle
Access the Clean Cycle at any time from the menu by holding
down the START Button for 3 seconds.
The Clean Cycle takes about 30 minutes to complete. The
drinkmaker will guide you through the cleaning process and
prompt you when it requires you to do such things as: adding
cleaning tabs, filling the Water Tank, or emptying the container.
After completing each step on the display, press the Right
Arrow Button to move to the next step. Press the Left Arrow
Button to go back to the previous step.
NOTE: Please make sure to keep the Pod Basket in the
drinkmaker while running a Clean Cycle.
30 mins
3 Tablets
1/2 Gallon
Container
Hold for 3
Seconds
XAM

16 17
4. Add three Drinkworks™ Cleaning Tablets to the
Water Tank.
7. Empty the half-gallon container down the drain and put it
back under the Tap.
5. Place a half-gallon container under the Tap.
8. Wait for Drinkworks™ Cleaning Tablets to completely
dissolve (approximately 10 minutes).
6. Press START Button to empty the drinkmaker. The
drinkmaker will Display “EMPTYING…” until this step
is complete.
9. Press START Button to begin cleaning (takes about 20
minutes). The drinkmaker will Display “CLEANING…” until
this step is complete.
10. Empty the half-gallon container down the drain and
put it back under the Tap.
11. Remove, empty, and wash the Water Tank.
10 mins
XAM
XAM
XAM

18 19
Your drinkmaker has a built in UV light to help keep your water
fresh. To prolong the life of the drinkmaker and maintain the
quality of drinks, we recommend that you run the Clean Cycle
every 30 days. Your drinkmaker will alert you anytime it thinks
you should clean it. If you would like to be reminded later
to clean simply press the Left Touch Arrow and you will be
reminded to clean 24 hours later. For the UV light to perform
its best, we recommend that you always keep your drinkmaker
plugged in and powered on.
Storage
Before you store your appliance make sure to do the following things:
1. Run an Empty Cycle.
2. Vent the CO2remaining in the CO2Cartridge and remove the CO2Cartridge
from the drinkmaker. See removal instructions on page 20.
3. Rinse, empty, and dry the Water Tank, Pod Basket, and Drip Tray.
4. Store your drinkmaker upright in a safe frost-free environment.
When you prepare to use your drinkmaker after storage, we recommend rinsing the
Water Tank with fresh water and running a Clean Cycle before you prepare your next drink.
Tutorials & Tips
Instructional videos are available online.
You can watch step by step videos on cleaning, rinsing, emptying, and more.
Visit www.drinkworks.com.
12. Refill the Water Tank to the MAX Fill and replace it on
the drinkmaker.
13. Press START Button to begin rinsing. The drinkmaker will
Display “RINSING…” until this step is complete.
14. Empty, dry and store the half-gallon container.
15. Insert water filter in the Water Tank and refill the
Water Tank.

20 21
2. Press and hold the blue CO2Gas Release Button to
release any remaining pressure, which will unlock the
cartridge from the drinkmaker. When pressurized, the
cartridge will be in the locked position.
3. When you no longer hear gas releasing, and the
Drinkworks™ CO2Cartridge is at room temperature,
pull the bottom of the cartridge away and up from
the appliance until the cartridge is sticking out at a
45-degree angle.
4. Hold the cartridge up at 45 degrees and unscrew until you
can remove the empty Drinkworks™ CO2Cartridge from
the drinkmaker.
NOTE: You may hear a final release of gas as you unscrew
the cartridge.
5. Dispose of the empty Drinkworks™ CO2Cartridge. See
disposal instructions on page 23.
Press &
Hold
45°
CO2Cartridge care
and replacement.
The on-board carbonation system.
Read and follow all warnings and instructions before using the Drinkworks™ Home Bar. It is
the owner’s responsibility to ensure that all users are aware of all warnings and precautions.
ONLY USE DRINKWORKS™ CO2CARTRIDGES WITH THE DRINKMAKER.
Please handle the Drinkworks™ CO2Cartridge with care.
WARNING: DRINKWORKS™ CO2CARTRIDGES contain gas under pressure; may explode if heated.
Protect from sunlight. Store in a well-ventilated place. Do not inhale. Do not drop. Do not use if
damaged. Do not tamper with or modify in any way. Empty cartridge before recycling or disposal.
Cartridges are not refillable. CARTRIDGES ARE NOT A TOY AND ARE NOT INTENDED FOR USE BY
PETS OR ANYONE UNDER THE AGE OF 18.
The carbonation system is pressurized, and cartridges can become quite cold when discharging
gas. Do not touch cartridge with bare skin during or immediately after discharging CO2. Wait for
the cartridge to get to room temperature before handling. Refer to the safety information (pg. 3),
or visit support for more information: www.drinkworks.com.
The Display on the drinkmaker will alert you when you are out of CO2and need to replace it. The
Display will also alert you when you have successfully installed the Drinkworks™ CO2Cartridge.
Drinkworks™ CO2Cartridge Removal
1. Remove CO2Side Door.
a. Place hand in the back groove of the CO2Side Door.
b. Pull away from the appliance (the door will pivot near
the front of the CO2Side Door on two tabs).
c. Slide the CO2Side Door tabs out and place the CO2
Side Door to the side.

22 23
Drinkworks™ CO2Cartridge Install
1. Insert full Drinkworks™ CO2Cartridge at a 45-degree angle
into the receiving end on the drinkmaker*. While holding
the cartridge up at a 45-dgree angle, screw in until the
cartridge is tight and not leaking. If you hear gas leaking
immediately tighten the Drinkworks™ CO2Cartridge by
screwing it in until the leaking stops. It is important to get a
tight seal and twist past the hiss.
WARNING: Drinkworks™ CO2Cartridge will get colder
over time if it is leaking CO2. Do not touch cartridge with
bare skin while it is leaking.
*NOTE: If the receiving end on the drinkmaker is in the
vertical position, pull it away from the appliance so that
it is at a 45-degree angle.
CAUTION: SHARP NEEDLE. DO NOT PUT FINGERS INTO
CHAMBER WHERE THE CARTRIDGE SCREWS IN.
2. Push down on the cartridge firmly until it locks into place.
The Drinkworks™ CO2Cartridge should be completely
straight (vertical) when in the correct position.
3. The drinkmaker will Display “CO2CARTRIDGE INSERTED
CORRECTLY” to confirm that you are ready to make
carbonated beverages.
4. Replace the CO2Side Door.
5. Ready to make carbonated drinks!
a. Slide the front tabs on CO2Side Door into their
corresponding slots.
b. Pivot the CO2Side Door towards the back of the
drinkmaker making sure that the front tabs stay
in their corresponding slots.
c. Push on the door until it clicks into place.
Tutorials & Tips
For tutorials and tips on installing the CO2Cartridge, as well as information on where and how to
purchase more Drinkworks™ CO2Cartridges, refer to the Drinkworks™ App or visit the website
www.drinkworks.com.
45°
Disposal
The Drinkworks™ CO2Cartridge is a multi-serve single use cartridge. Do not attempt to refill or
tamper with it in any way. The Drinkworks™ CO2Cartridge is recyclable when empty. As long as
the cartridge has been used in the drinkmaker it will be fully empty. Please recycle.
For more information visit the website www.drinkworks.com.

24 25
Drinkmaker status. Troubleshooting.
The START Button light ring indicators:
Unlit
The drinkmaker is off or in standby mode. To wake up from
standby mode simply press the START Button or lift the Handle
on the Pod Door.
Solid Blue
The drinkmaker is working.
Flashing Blue
The drinkmaker is ready to prepare a drink.
Red
The drinkmaker needs assistance. See the Display
for information.
Flashing Red
A more serious error has occurred.
Contact Drinkworks™ support: 1-855-DRINKWORKS
(1-855-374-6596)
My drinkmaker does not recognize my authentic
Drinkworks™ Pod.
If the drinkmaker fails to recognize your authentic Drinkworks™
Pod, try opening the Pod Door and re-inserting the Pod. Make
sure that the Pod is in the correct position with the barcode at
the 12 o’clock position. After two failed attempts to determine
what type of Drinkworks™ Pod you selected, the drinkmaker
will enter an override state. Follow the instructions on the
drinkmaker’s Display and do the following:
1. Open the Pod Door on the drinkmaker by lifting on
the Handle and remove the Pod.
2. Find the Pod type written on the Drinkworks™ Pod
label. The type should be a capital letter located in a
triangle under the word “Pod Type”.
3. Scroll to the correct letter on the Display using the
the Touch Arrow Buttons.
4. Push the START Button to select approriate Pod Type.
5. Re-insert the Pod and close the lid.
6. Press the START Button to make your drink.
THIS UNIT NOT LABELED FOR
INDIVIDUAL SALE
PACKED BY DRINKWORKS
TM
WILLISTON, VT
NON-ALCOHOLIC
1.7 FL OZ MAKES 6.8 FL OZ AS SERVED BY YOUR DRINKMAKER
Bright Lemon Flavor and a Hint of
Muddled Basil
Serve over cubed ice in a highball
glass with a lemon wedge, with or
without gin of your choice.
SWEETNESS
HERBAL CITRUS
NOTES:
PART GEOMETRY CONTROLED BY CAD FILE OF SAME NUMBER. REFER TO GENERAL TOLERANCE BLOCK 1.
TO CONTROL TOLERANCES NOT SHOWN.
PART MUST MEET ALL REQUIREMENTS LISTED IN DESIGN SPECIFICATION #70002554 2.
FLAT PARTS DRAWN OUTSIDE UP. 3.
40000609
BRANDING LABEL, 50ml
M. FANTAUZZI
C
70002556
TITLE
MATERIAL
DRAWN BY
REV PART NUMBER
PANTONE
427C
PANTONE
Cool Gray 6
Black
Drinkmaker does not have power
Check to be sure that it is plugged in securely.
Make sure that the Power Button in back has been turned on.
Plug drinkmaker into an independent outlet.
Plug into a different outlet.
Reset your home’s circuit breaker, if necessary.

26 27
My drinkmaker is taking a long time to cool down. What should I do?
To avoid long cool down times always keep your drinkmaker plugged in a powered
on. This will make sure that the water in the internal reservoir stays at the perfect
temperature.
Adding ice to the Water Tank will help the internal reservoir cool down faster.
Try running an Empty Cycle to remove warm water from the internal reservoir. Then add
ice to the Water Tank to refill the internal reservoir with ice and water to cool down faster.
If you continue to have long cool down times please contact DrinkworksTM Support:
1-855-DRINKWORKS (1-855-374-6596).
My drinkmaker just Displayed “SORRY, OUT OF CO2DRAINING WATER…”
What happened?
Your drinkmaker did not have enough CO2to make a carbonated drink. Don’t worry. If the CO2
runs out while the drinkmaker is preparing to make a drink, the Pod in use will be saved for the
period needed to replace the CO2Cartridge. Keep a glass under the Tap as the drinkmaker will
empty the unused water. When this occurs, follow the prompts on the drinkmaker’s Display.
My drinkmaker just Displayed “CLEAN CYCLE INTERRUPTED.” What happened?
Something happened during your Clean Cycle and you did not finish cleaning your drinkmaker.
The drinkmaker will guide you through finishing the Clean Cycle process and remove any cleaning
solution that is inside your drinkmaker.
For more information regarding error codes, refer to the Drinkworks™ App
or visit the website www.drinkworks.com.
Drinkmaker will not make a non-carbonated drink
After placing the Drinkworks™ Pod in the Pod Basket, make sure the Pod Door is all the
way down and the blue button is flashing. If the drinkmaker does not recognize the Pod,
follow the steps outlined above under “My drinkmaker does not recognize my authentic
Drinkworks™ Pod”.
Check to see if the drinkmaker Display reads “FILL WATER TANK”. If so, add water to the
Water Tank. Fill to, and not beyond, the MAX Fill line. Make sure the Water Tank is seated
properly on its base.
If you continue to see “FILL WATER TANK” on the Display, contact Drinkworks™ support:
1-855-DRINKWORKS (1-855-374-6596).
Drinkmaker will not make a carbonated drink
Follow steps above for assistance with a non-carbonated drink.
Check to see if the drinkmaker says “CHILLING… READY IN XX MINS”. If so, the water in
the internal reservoir is too warm for carbonated drinks. Please wait the time indicated on
the Display and try again.
Check to see if the drinkmaker Display reads “FILL WATER TANK”. If so, add water to the
Water Tank. Fill to, and not beyond, the MAX Fill line. Make sure the Water Tank is seated
properly on its base.
If visible, press the Left Touch Arrow on the Display to determine if you need to replace
your CO2Cartridge. If Display shows “REPLACE CO2CARTRIDGE”, do the following:
Press (do not hold) the blue CO2Gas Release Button to see if there is any gas
remaining. If you get a soft hiss or if there is no gas, then please replace the CO2
Cartridge with a new one. If you get a loud hiss, then proceed to the next step.
Confirm that the CO2Cartridge is in the correct position. Pull the CO2Cartridge
away from the drinkmaker and push it back towards the drinkmaker until it
is straight (vertical). The Display should confirm that the “CO2CARTRIDGE
INSERTED CORRECTLY”.
If you continue to see the same error message on the Display after troubleshooting
contact Drinkworks™ support: 1-855-DRINKWORKS (1-855-374-6596).

28 29
Helpful hints.
Plug drinkmaker directly into a
grounded outlet
If the electric circuit is overloaded with
other appliances, your drinkmaker may not
function properly. The drinkmaker should be
operated on its own circuit, separate from
other appliances.
Keep your drinkmaker turned “ON”
To make your favorite drinks anytime you
want, keep your drinkmaker plugged in and
powered on all the time. This allows you to
avoid long wait times to set up the drinkmaker
and to chill water before you can prepare
your favorite drink.
For the best tasting drinks,
Drinkworks™ recommends using
bottled or filtered water
Water quality varies from place to place.
If you notice an undesirable taste in your
drinks (such as chlorine or other mineral
tastes), we recommend you consider using
bottled water or water from a filtration
system. For best results, carefully follow
manufacturer’s instructions when using any
water filtration system.
Home Bar Warranty.
Drinkworks™ drinkmaker will be free of
defects in materials or workmanship under
normal home use for one (1) year from the
date of purchase. We recommend that you
register your drinkmaker by visiting
www.drinkworks.com/register,
downloading and syncing the Drinkworks™
App for Apple iOS, or Google Android,
or calling toll-free
1-855-DRINKWORKS (1-855 374-6596)
so that your purchase information will be
stored in our system. Drinkworks will, at
its option, repair or replace a defective
drinkmaker without charge upon its receipt
of proof of the date of purchase. If we opt
to replace your drinkmaker to service this
warranty, the replacement brewer may
be new or reconditioned. If you receive
a replacement drinkmaker, your existing
warranty end date will be applied to the
replacement. This warranty only applies to
drinkmakers operated in the United States
and Canada. This warranty gives you specific
legal rights, and you may also have other
rights that vary from state to state and, in the
case of Canada, from province to province.
Contains FCC ID: A8TBM71S2
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device may
not cause harmful interference, and (2) this
device must accept any interference
received, including interference “that may
cause undesired operation”.
We can only guarantee the proper functioning
and lifetime of your drinkmaker if you use
Drinkworks Pods and Drinkworks Accessories.
Any damage to or malfunction of your
drinkmaker resulting from the use of non-
Drinkworks Pods or Accessories may not be
covered by this warranty or may result in a
service fee if the damage or malfunction is
determined to be caused by such use. For
information on ongoing maintenance and how
to keep your drinkmaker functioning properly
please refer to your Home Bar Care Guide or
visit us at www.drinkworks.com.
Remove Drinkworks™ Pod after use
Do not leave your Pod in your drinkmaker.
Remove it after your drink has been
made. Please see page 05 for drink
making instructions.
Add ice to the Water Tank
To get your drinks to the right temperature
faster or to make a lot of cold drinks with
less waiting, start with ice cold water in the
Water Tank.
Clean the Pod Basket weekly
Remove the Pod Basket and hand wash it or
clean it in the top rack of the dishwasher.
Run a Clean Cycle once a month
Your drinkmaker’s Display will let you know
when it is time to run a cleaning cycle.
Tilt your glass when you pour a beer
To achieve the desired combination of foam
and liquid, start with a chilled glass and give it
a quick rinse. Tilt the glass under the Tap and
gradually straighten it to an upright position
when pouring a beer. This may take a little
practice to achieve the desired combination
of foam and liquid.

Please contact us. We’d like to hear from you.
Drinkworks™
1-855-DRINKWORKS (1-855-374-6596)
[e-mail]
Follow us for updates on all things Drinkworks™
Contact Us.
Questions or suggestions?
Drinkworks™ Pods, CO2Cartridges, and other available accessories are sold separately.
This drinkmaker is designed to prepare alcohol beverages and is intended for use by persons 21+ years old.
Please enjoy responsibly!
The Drinkworks™ name and logo are the property of Bedford Systems LLC. All third-party
trademarks or logos referenced in this guide are the property of their respective owners.
KEURIG®is a trademark of Keurig Green Mountain, Inc., used under license.
© 2018 Bedford Systems LLC