Keurig KOLD How to use

start here

introducing, your drinkmaker 4
display panel 5
setup 6
prime & rinse 7
make a drink 8
party mode 10
KOLD™pods 11
cleaning 12
get more from KEURIG®KOLD™13
troubleshooting 14
!
let’s get going

D
E
A
BC
F
G
I
J
H
introducing, your drinkmaker
A. Water reservoir cover
B. Water reservoir
C. Mixer drawer
D. Drip tray cover
E. Drip tray
F. Power cord
G. Display panel
H. Top cover
I. Front cover
J. Pod holder insert
K. Handle
4
For full drinkmaker safety information,
refer to Important Safeguards insert.
K

display panel
A. KOLD™ button
The ring color around the KOLD™ button indicates the state that the drinkmaker is in.
It will be blinking to indicate when you need to take action.
B. KOLD™ chiller gauge
The KOLD™ chiller gauge tells you how much cold beverage capacity is in the KOLD™ chiller.
C. Snowake
The snowake will stay lit when the drinkmaker can make a beverage and blink
when it still needs to chill.
D. Water reservoir sensor
The Water reservoir sensor will blink blue when you need to add water.
A
B
C
D
5
ready
for
priming
ready to
make a
beverage
see
troublshooting
for help
not ready,
chilling

setup
6
1. Plug in drinkmaker.
Since there’s no on-o button, keep your drinkmaker plugged in at all times
(it will use about the same amount of energy as a mini-fridge).
2. Allow 2 hours to chill.
During initial chill, the fan noise will be loud, but will minimize once complete
and during normal operation.
3. Your drinkmaker operates best in cooler air temperatures.
Keep it indoors, out of direct sunlight, away from heat sources such as a stove,
and ideally, about 2" away from the wall.
1
Is it time to prime?
2"

prime & rinse
Before you begin enjoying your beverages,
the system must be primed and rinsed after the
initial 2 hour chilling.
1. Fill Water reservoir with room temperature or cooler water.
2. Insert the Prime & care pod.
The KOLD™ button will blink purple.
3. Place glass on drip tray. Press KOLD™ button to start cycle.
In about a minute, 8 oz. of rinse water will be dispensed.
Dispose of liquid.
4. Once complete, remove Prime & care pod and save
for future cleansing.
The KOLD™ button will be lit blue when cycle completes.
Is it time to prime?
No, still
chilling.
Yes, it’s ready
to prime!
7Visit Keurig.com/KOLD for more information and instructional videos.

8
make a drink all your favorites, fresh-made at the push of a button.
Is your drinkmaker ready? 1. Select a KOLD™ pod and
remove freshness seal from
the bottom. Insert pod into
the drinkmaker.
IMPORTANT: If you do not remove the
freshness seal, beverage will not properly
dispense and pod will be wasted.
Yes, it’s
ready to go!
No, still need
to prime.
See pg. 7
No, still
chilling.
sparkling still
OR

9
2.When the KOLD™ button blinks
blue, press the KOLD™ button to
begin making your beverage.
3. Remove KOLD™ pod after
beverage is dispensed.
NOTE: Sparkling KOLD™ pods
will be warm to the touch.
ENJOY!
Visit Keurig.com/KOLD for more information and instructional videos.

party mode
After initial chilling, the drinkmaker is ready to make 6 beverages.
If you’re entertaining or notice your KOLD™ chiller gauge is low,
you can keep the good times going by using Party Mode.
Simply add ice to Water reservoir, then add water, and you’ll
be able to make even more beverages in a row.
10

Things you should know:
•Before inserting the KOLD™pod into the
drinkmaker, remove freshness seal from
bottom of the pod.
•Line up the notch in the pod with the notch
in the back of the Pod holder.
•For best results, store KOLD™pods at room
temperature (60˚F -80˚ F). Do not refrigerate.
•All pods are single use.
•DO NOT eat or handle Karbonator™ beads.
•For full Karbonator™ bead safety information,
refer to Important Safeguards insert.
KOLD™pods
11
sparkling
(with Karbonator™ beads)
OR
still
sodas
seltzers
craft sodas
tonics
mixers
cocktail mixers
iced teas
sports drinks
avored waters
Visit Keurig.com/KOLD for more information and instructional videos.

1212
cleaning clean your drinkmaker weekly to keep it running smoothly.
Top rack dishwasher safe
• Water reservoir cover
• Drip tray cover
• Drip tray
• Mixer drawer
• Front cover
Hand wash only
• Water reservoir
• Pod holder insert
Wipe with damp cloth
• Pod holder Water reservoir
Gently lift Water reservoir
to remove, and then
set back securely
after cleaning.
NOTE: Do not unplug the
drinkmaker during cleaning.

Water reservoir
Gently lift Water reservoir
to remove, and then
set back securely
after cleaning.
13
Drip tray
Drip tray can be removed
and replaced, by sliding it
out or in the drinkmaker.
Mixer drawer
Lift the drinkmaker
Handle and pull out the
Mixer drawer; replace
by pushing in.
Pod holder insert
Insert nger into Pod
holder and gently lift.
To replace, line up notches
and push down lightly.
Front cover
Remove the Drip tray, then
gently push up the tab on
the bottom of the Front cover.
Wiggle slightly to remove.
Visit Keurig.com/KOLD for more information and instructional videos.

13
get more from KEURIG®KOLD™
On-demand cold water.
Close the Handle without
inserting a KOLD™ pod.
The KOLD™ button will blink
blue. Push to dispense
ice cold water!
KOLD™ Accessories
Visit Keurig.com/KOLD
for drinkmaker accessories,
including pod storage
and glassware.
Water Filter
Ensure your beverages
taste their best.
Visit Keurig.com/KOLD
to learn more.
Cleansing Care
Visit Keurig.com/KOLD
to learn more
about cleansing.
14

I inserted a pod but the KOLD™ button
isn’t blinking blue.
Check that the handle is fully closed.
I inserted a pod and the KOLD™ button is blinking red.
Be sure the Mixer drawer is pushed in fully.
My drink doesn’t have any avor.
If you are using a still pod, please try again.
If sparkling, select a fresh pod. Remember to remove
the freshness seal from the bottom of the pod before
inserting into the drinkmaker.
There seems to be a lot of water in the Drip tray.
Ensure the Mixer drawer is pushed in fully. Conrm
the Water reservoir is properly seated. If problem
persists, please contact Customer Care.
The KOLD™ button blinked red while making a
beverage and now my drink doesn’t appear to
be carbonated or avored.
Try again with a fresh pod. If the problem persists,
please call Customer Care.
My drinkmaker is making less than six beverages in a row.
Be sure your drinkmaker is out of direct sunlight,
away from heat sources and 2 inches from the wall.
My drinkmaker is taking longer than 2 hours to chill.
Be sure your drinkmaker is out of direct sunlight, away
from heat sources and 2 inches from the wall.
The KOLD™ button is red and I cannot
make a beverage.
Please call Customer Care.
For Customer Care, contact:
1-855-KRG-KOLD | 1-855-574-5653 | www.Keurig.com/KOLD
troubleshooting
15
Visit Keurig.com/KOLD for more information and instructional videos.

Get a special oer
when you register your
drinkmaker online!
You’ll need the serial number located underneath
the top cover of the drinkmaker