Keys Fitness Stepper Machine E2-0 User manual

315-00131
09/18 Rev 9.0
Owner’s Manual
Customer Service
[phone]
Manufactured By:
Keys Fitness Products
4009 Distribution Drive
Suite 250
Garland, TX 75041
Read all precautions and instructions
in this manual before using this equip-
ment.
KF-E2.0
Model Name : KF-E2.0
Serial Number :
Serial Number can be found at
the above specified location.
CAUTION

2
www.keystness.com
Table of Contents
Table of Contents 2
Important Safety Information 3
Assembly 4
Parts Identifier 5
Assembly Steps 6
Console Information 18
Maintenance Instruction 25
Workout Information 27
Parts list 31
Exploded View 33
Warranty 35
TABLE OF CONTENTS THANK YOU for making this unit a part of your exercise program. Keys Fitness
Products Fitness assures the very best in value, appearance, durability and biome-
chanics. This manual will guide you through the assembly process. If at any time
you are having trouble with the assembly or use of this product, then please con-
tact us at our Keys Fitness Help line. We have trained service technicians on site
to take care of you, our valued customer.
REGISTRATION CARD
To avoid unnecessary delays in warranty parts and to insure that a permanent
record of your purchase is on file with our company, be sure to send in the war-
ranty registration card or register on-line at www.keysfitness.com within 10 days of
purchase.
Keys Fitness series
MODEL: KF-E2.0
QUESTIONS?
CALL
[phone]
Monday-Friday
8:30 am - 5:30 pm Central Time

3
www.keystness.com
WARNING! Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age
of 35 and/or persons with pre-existing health problems. The manufacturer or distributor assumes no responsibility for personal injury or property
damage sustained by or through the use of this product. To reduce the risk of electrical shock, burns, re, or other possible injuries to the user, it is
important to review this manual and the following precautions before operation.
SAFETY PRECAUTIONS AND TIPS
1. It is the owner’s responsibility to ensure that all users of this unit have read the Owner’s Manual and are familiar with warnings and
safety precautions.
2. This unit has a user maximum capacity of 275 pounds.
3. The unit should only be used on a level surface and is intended for indoor use only. The unit should not be placed in a garage,
patio, or near water and should never be used while you are wet. Keys Fitness recommends a mat be placed under the unit to
protect oor or carpet and for easier cleaning.
4. Follow safety information in regards to plugging in your unit. Do not run the power cord underneath your unit. Do not operate the
unit with a damaged or frayed power cord.
5. Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the unit with bare feet, sandals,
socks or stockings.
6. Always examine your unit before using to ensure all parts are in working order.
7. Allow the unit to fully stop before dismounting.
8. Pets should never be allowed near the unit.
9. Do not leave children unsupervised near or on the unit.
10. Never operate the unit where oxygen is being administered, or where aerosol products are being used.
11. Never insert any object or body parts into any opening.
12. For safety and to prevent damage to your unit, no more than one person should use the unit at a time.
13. Always unplug the unit before cleaning and/or servicing. Service to your unit should only be performed by an authorized service
representative, unless authorized and/or instructed by the manufacturer.
14. Failure to follow these instructions will void the unit warranty.
Thank you for purchasing the Keys Fitness KF-E2.0! The quality product you have chosen was designed to meet your needs for
cardiovascular exercise. Before you start, please read the Owner’s Manual and become familiar with the operation of your new unit. Remember
to take time to perform stretching exercises, provided in this manual, to help avoid injury. If you are taking medication, consult your physician to
see what effect the medication will have on your exercise heart rate. If you have heart problems, you are not active, and/or are over the age of 35
years, do not use the pre-set programs or start an exercise program without rst contacting and receiving approval from your physician. To avoid
the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. Keys Fitness recommends a sealed water bottle for
beverages consumed while using the unit.
Important Safety Information

4
www.keysfitness.com
Assembly

5
www.keystness.com
Parts Identifier
Prior to assembly, remove components from the box
and verify that all the listed parts were supplied.
Right Rotating
Handlebar
Allen Screws
M8x58
Left Rotating
Handlebars
Right Handlebar
Left Handlebar
Bottle Holder
Water Bottle
Rotating Arm - Pedal assembly (Right)
A
C
Wheel Tracks
B
Front stabilizer D
Upright post
J
Console
Upright tube cover
H
F
G1
E1
Tools
Main Frame
Allen Screws
M8x70
Allen Screws
M8x20
Allen Screws
M10x112
Screws (Black)
M5x20 Allen Screws
M6x10 Allen Screws
M8x15
Allen Screws
M8x20
Screws
M4x10 Spring Washers M8 Flat Washers
M8x16x1.2 Flat Washers
M10xø22x1.5
Spring Washers
M10
Bushings
Flat Washers
M8xø22x2.0
Flat Washers
M8xø38x2.0
Nut M8
N2
N1 N3 N4
N5 N6 N7 N8
N10 N13 N14 N15
N17
N18
N20
N21
N22
K1 K2
Rotating Handlebar
Tube - Left
Rotating Handlebar
Tube - Right
P1
P2
Pedal Arm
Cover - Left
L-L Pedal Arm
Cover - Right
L-R
6mm 5mm 13mm
14mm
E2
G2

6
www.keystness.com
Assembly
1
N4
A
B
N17
N15
Use Tool
6mm
ASSEMBLY FOR FRONT STABILIZER
Secure the front stabilizer (B) to the main
frame (A) using 2 allen screws (N4), 2 spring
washers (N17) and 2 flat washers (N15).

7
www.keystness.com
C
C1
N1 N13
N14
A
Assembly
Use Tool
6mm
Note: After finishing the installation of both the
front stabilizer bar and the rear wheel tracks, in
order to add stability to the unit, you may need
to adjust the levelers that are located on the
bottom of the stabilizer bars.
ASSEMBLY FOR REAR WHEEL TRACKS
Secure the rear wheel tracks (C) to the main frame
(A) using screws (N1), springs washers (N13), and flat
washers (N14).

8
www.keystness.com
Assembly
3
D
H
D2
A2
A
N7
N13
N14
Use Tool
6mm
ASSEMBLY FOR UPRIGHT POST
Step 1:
Insert the upright post cover (H) onto the upright post (D)
from the bottom side.
Step 2:
Connect the lower sensor wire (A2) with the upper sensor
wire (D2).
Step 3:
Mount the upright post (D) to the main frame (A) and secure
using 4 allen screws (N7), 4 spring washers (N13), and 4 flat
washers (N14).
Step 4:
Slide the console tube cover down to conceal tube
connection.

9
www.keystness.com
Assembly
4
D
G2
G1
E1
N8
N13
N21
N3
N13
N14
P1
N6
G1-1
G1
D
D2-1
Use Tool
6mm
Use Tool
5mm
ASSEMBLY FOR RIGHT
HANDLEBAR
Step 1:
Connect the right rotating handlebar tube
(P1) to the upright post (D) at the arm joint
and secure using allen screw (N8), spring
washer (N13) and flat washer (N21).
Step 2:
Attach the right rotating handlebar (E1) to
the right rotating handlebar tube (P1) and
secure using 4 allen screws (N3), 4 spring
washers (N13), and 4 flat washers (N14).
ASSEMBLY FOR STATIONARY
HANDLEBARS
Step 1:
Connect the pulse wire (G1-1) from the
right handlebar (G1) to the pulse wire
(D2-1) from the upright post (D).
Step 2:
Attach the right stationary handlebar
(G1) to the right handlebar mount on the
upright post (D) and secure using 3 allen
screws (N6).
Step 3:
Repeat steps 1 and 2 for the left station-
ary handlebar (G2).

10
www.keystness.com
Assembly
5
N18
A
P1
N13
N2
N14
P1
N22
Use Tool
6mm
ASSEMBLY FOR RIGHT ROTATING
HANDLEBAR TUBE
Step 1:
Insert 2 bushings (N18) on the tapered ends into the right pedal
arm joint (A) - one for each side.
Step 2:
Attach the right pedal arm (A) to the right rotating handlebar tube
(P1) and secure using allen screw (N2), spring washer (N13), flat
washer (N14) and nut (N22).
Use Tool
13mm14mm

11
www.keystness.com
Assembly
6
D
P2
N8
N21
N13
N13 N20
N8 F
Use Tool
6mm
ASSEMBLY FOR LEFT ROTATING HANDLEBAR
Connect the left rotating arm (P2) to the upright post (D)
at the arm joint and secure using allen screw (N8), spring
washer (N13) and flat washer (N21).
ASSEMBLY FOR LEFT PEDAL
Locate the left pedal assembly (F) and attach it to the
main frame (A) at the pedal tube mount. Secure with
allen screw (N8), spring washer (N13) and flat washer
(N20).

12
www.keystness.com
Assembly
7
Use Tool
6mm
ASSEMBLY FOR LEFT ROTATING
HANDLEBAR TUBE
Step 1:
Insert 2 bushings (N18) on the tapered ends into
the left pedal arm joint (F) - one for each side.
Step 2:
Attach the left pedal arm (F) to the right rotating
handlebar tube (P2) and secure using allen screw
(N2), spring washer (N13), flat washer (N14) and
nut (N22).
N18
N18
P2
F
P2
F
N2
N13 N14
N22
Use Tool
13mm14mm

13
www.keystness.com
8
Assembly
ASSEMBLY FOR FILLING WASHER
Step 1:
If the arms appear to have too much side to side movement, check and see if there is any gap in between the handlebar tube and the upright post
arm joint by inserting one or more filling washers in the handlebar tube connection.
Step 2:
If there is a gap for the filling washer to fit, the handlebar(s) should be uninstalled to fit the filling washer in the handlebar joint. Note that the filling
washer can be inserted on the right handlebar, left handlebar or both (2 filling washers have been included).
Step 3:
Re-install the handlebar assembly to the upright post.
FILLING WASHER
FILLING WASHER
N8 N13 N21
P2
P1
N8
N13
N21
D

14
www.keystness.com
Assembly
9
J
D
E2
K1
K2 N5
P2
N3
N13
N14
L-(L)
N10
J
J1
D
ASSEMBLY FOR PEDAL JOINT COVER
Step 1:
Install left pedal joint cover (L-L) to conceal pedal arm connection and secure using
screw (N8).
Step 2:
Repeat step 1 on the right side with right pedal joint cover (L-R).
ASSEMBLY FOR CONSOLE
Step 1:
Remove the screws (J1) from the back of the console.
Step 2:
Connect the pulse wires, sensor wires and the toggle wires with the corresponding
wires on the console.
Step 4:
Gently slide the wires down the upright post and secure the console (J) to the upright
post (D) using the screws (J1).
ASSEMBLY FOR WATER BOTTLE HOLDER
Step 1:
Attach the water bottle holder (K2) and secure to the
upright post (D) using 2 screws (N5).
Step 2:
Place water bottle (K1) inside water bottle holder (K2).
Use Tool
6mm
Use Tool
13mm14mm
ASSEMBLY FOR LEFT ROTATING HANDLEBAR
Attach the left rotating handlebar (E2) to the left rotating handlebar tube (P2) and se-
cure using 4 allen screws (N3), 4 spring washers (N13) and 4 flat washers (N14).

15
www.keystness.com
Congratulations!
You have completed the assembly of
your new Keys Fitness E2.0 Elliptical!
Assembly

16
www.keystness.com
Adapter (M)
Assembly
ADAPTOR PLUG-IN LOCATION

17
www.keystness.com
MOVING YOUR UNIT
TRANSPORT WHEELS
Assembly

18
www.keysfitness.com
Console Information

19
www.keystness.com
Console Information
• Before starting any exercise
program, consult your physician.
• For your safety, please consult
owner’s manual ca refully before using.
CAUTION:
314-00185
DISPLAY:
1) Program Selection
Manual, Program (presets), and Watt
2) Segment Program Prole
Rows signify tension level, whereas
columns signify interval of time
3) Time
4) Speed
5) One touch program prole buttons
6) Start / Stop Key
7) Recovery Key
Evaluates overall tness level
8) Up (+) and Down (-) Keys
9) Reset Key
Resets function values to default
10) Mode
Conrms selection
11) Distance
12) Watt / Calories
13) User Data Display
Displays the user selected prole
1
2
34
5
678910
11
12
13

20
www.keystness.com
Console Information
CONSOLE FUNCTION PARAMETERS
TIME 0:00~99:59.
WATTS 0~999 WATTS
CALORIES 0~9999
TEMPERATURE 0~60ºC / 32~99ºF
GENDER FEMALE / MALE
AGE 10-99
HEIGHT 100-200 (CM) / 40-80 (INCH)
PULSE P~30~240
HEART SYMBOL ON / OFF blinks
PROGRAM P1~P12
WATT CONSTANT 10~350 WATTS
PERSONAL U1~U4
WEIGHT 20-150 (KG) / 40-350 (LB)
CONSOLE BUTTONS:
START/STOP:
This button is used to start or stop training
RECOVERY:
This button is used to begin the Recovery feature of the console (refer to Console Function section for more information).
UP/DOWN:
These buttons are used to change programs and settings. During your workout, these buttons are used to increase / decrease resistance.
RESET:
This button is used to return to main menu screen at any time. It is also used to reset all values to zero.
MODE:
This button is used as an enter key, and will allow user to move to the next setting that can be changed. When pressed and held for 2 seconds or
more, console will go back to the user prole selection screen.
ONE TOUCH PROGRAM PROFILE BUTTONS:
These 12 program prole one touch buttons allow quicker selection to the desired type of workout.