KEYSCO TOOLS 77780 User manual

KEYSCO TOOLS
DIVISION OF S&H INDUSTRIES, INC.
5200 Richmond Road Cleveland, OH 44146
Phone [phone] Toll Free 800-253-9726 
Fax [phone]
www.shindustries.com
E-Mail: [e-mail]
MADE IN THE USA Rev. 1/19/12
FENDER STAND – 77780
The Keysco Tools Fender Stand will hold two fenders for doing all prep work, including painting,
grinding, sanding, etc. The Fender Stand is designed to fit all fenders, both foreign and domestic.
There are not tools required to hang a fender on the Keysco Tools Fender Stand – simply hang
fender on mounting pins (#11) and adjust T-bars (#8) until fender is secure.
DO NOT TIGHTEN HARDWARE UNTIL ALL PARTS ARE INSTALLED
Key # Part # Description Qty. Key # Part # Description Qty.
1 11378 Cap bracket 2 10 11373 Angle support 4
2 11370 45Upright 2 11 11380 Mounting pins 4
3 11369 Straight upright 2 12 10201 1/4 Hex nut 8
4 11375 Extension tube 4 13 10675 1/4-20 x 2” Bolt 8
5 11372 Horizontal support 2 14 11381 Protective cap 16
6 11366 Floating slide bar 4 15 11379 Knob 16
7 11371 Straight bar 2 16 10178 1/4-20 Locknut 2
8 11374 T-bar 4 17 10676 1/4-20 x 1-1/2” Bolt 6
9 11368 Cross member 2 18 11498 Bumper extender tube 2

77780 Assembly Instructions
Page 2
ASSEMBLY INSTRUCTIONS
Before assembly, make sure you have all parts. Review the parts packing list.
Do not tighten hardware until all parts are installed.
1. Leg assembly (A-frame legs): Place 1 each of #2 (45) upright) against 1 each of #3 (straight upright)
and assemble with 1 each of #1 (cap bracket) using 3 each of #17 (1/4-20 x 1-1/2” bolts) and 2 each of #12
(1/4-20 hex nut) and 1 each of #16 (1/4-20 locknut). Be sure to place #16 (1/4-20 locknut) on #17 (1/4-20 x
1-1/2” bolt) going through #2 (45upright).
Note: Tighten lock nuts so the 45upright moves freely. Assemble both A-frame legs as illustrated in
Figure #1. Figure #1
2. Extension tube assembly: Start #15 (knob) into #4 (extension tube). DO NOT TIGHTEN. Now
assemble all #15 (knobs) into #4 (extension tubes). The extension tube/knobs are now ready to use to
complete assembly.
3. Extension tubes mounted on uprights (A-frame legs): Place #4 (extension tube) with #15 (knob)
pointed out on #2 (45upright) which you have assembled. Slide to upper portion of A-frame leg. Finger-
tighten only (do both sides – extension tubes). Slide #6 (floating slide bars) onto #5 (horizontal support).
Mount #5 (horizontal support) onto #4 (extension tube) with #13 (1/4-20 x 2” bolt).
4. Angle support – Mount on A-frame legs: Start 2 each of #15 (knobs) into all #10 (angle supports. The
angle supports are now ready to use to complete assembly. Install 1 #10 (angle support) on the upright
from the bottom with horizontal tube facing in. Tighten knob to secure to the upright. Place #8 (T-bar) into
#10 (angle support), install #7 (straight bar) through #8 (t-bar) and insert #15 (knob into #8 (T-bar) and
tighten.
5. You are now ready to install all of your parts. Each side of the Fender Stand installs the same way:
Lay #9 (cross member) between A-frame legs after all other parts have been installed on both 45upright
and straight uprights. Insert #13 (1/4-20 x 2” bolt) through both uprights and finger-tighten.
6. You are now ready to begin final adjustments to the Keysco Tools Fender Stand. Tighten all bolts
and locknuts. You may now hand-tighten the #15 (knobs), being sure to never tighten them with pliers or
wrench. Finger-tightening is more than adequate to hold the fenders in place.
7. Place #14 (protective caps) on each end of #5 (horizontal supports), #7 (straight bars) and #8 (T-
bars.)